PureGear - Audio Gear, Charges, Cases, Phone Accessories & More
User Manual for pure gear models including: YJW-11139PG, YJW11139PG, 11139pg, Magnetic Selfie Stick Tripod Stand, Magnetic Selfie Stick, Selfie Stick, Magnetic Tripod Stand, Tripod Stand
Superior communications . 11139PG Bluetooth Magic Selfie stick YJW-11139PG YJW11139PG 11139pg
File Info : application/pdf, 1 Pages, 2.10MB
DocumentDocumentMagnetic Selfie Stick Tripod Stand Magnetic Selfie Stick Tripod Stand User Manual Manual del usuario ENGLISH Connecting / Bluetooth Pairing 1. Make sure the PureGear Magnetic Selfie Stick Tripod Stand remote is within 2-3 ft (0.6-0.9m) of the device you will be connecting to. 2. Turn on your device's Bluetooth. Most devices will automatically detect your PureGear Magnetic Selfie Stick Tripod Stand remote. Locate and select "PG Selfie Stick". If your device does not automatically detect your remote, make sure Bluetooth is turned on, do a SEARCH for "PG Selfie Stick" and then click CONNECT. Operating the PureGear Magnetic Selfie Stick Tripod Stand 1. Lift up the bracket. 2. For non-MagSafe phones, insert mobile phone into silicone holder. 3. For MagSafe phones, remove the silicone phone holder and attach directly to the magnetic ring. ESPAÑOL Connecting / Bluetooth Pairing 1. Make sure the PureGear Magnetic Selfie Stick Tripod Stand remote is within 2-3 ft (0.6-0.9m) of the device you will be connecting to. 2. Turn on your device's Bluetooth. Most devices will automatically detect your PureGear Magnetic Selfie Stick Tripod Stand remote. Locate and select "PureGear Selfie Stick". If your device does not automatically detect your remote, make sure Bluetooth is turned on, do a SEARCH for "PureGear Selfie Stick" and then click CONNECT. Operating the PureGear Magnetic Selfie Stick Tripod Stand 1. Lift up the bracket. 2. For non-MagSafe phones, insert mobile phone into silicone holder. 3. For MagSafe phones, remove the silicone phone holder and attach directly to the magnetic ring. 4. To use tripod, open the base and extend the telescoping neck to the desired position. Note: If the support does not close completely, please press the upper area with your fingers to close. 4. To use tripod, open the base and extend the telescoping neck to the desired position. Note: If the support does not close completely, please press the upper area with your fingers to close. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: YJW-11139PG Cumplimiento con la FCC Este dispositivo cumple con la Parte 15 de las reglas de la FCC. La operación está sujeta a las siguientes dos condiciones: (1) este dispositivo no puede causar interferencia dañina, y (2) este dispositivo deberá aceptar cualquier interferencia recibida, incluyendo interferencia que pudiera causar una operación indeseable. Advertencia: Los cambios o modificaciones a esta unidad que no estén expresamente aprobados por la parte responsable del cumplimiento podrían anular la autoridad del usuario para operar el equipo. NOTA: Este equipo ha sido probado y se encontró que cumple con los l ímites establecidos para un dispositivo digital Clase B, de conformidad con la sección 15 de las reglas de la FCC. Estos límites están diseñados para ofrecer protección razonable contra interferencias perjudiciales cuando el equipo se opere en una instalación residencial. Este equipo genera, usa y puede emitir energía de radio frecuencia, y si no se instala y usa de conformidad con las instrucciones podría provocar interferencia perjudicial en las comunicaciones de radio. Sin embargo, no se garantiza que dicha interferencia no ocurrirá en una instalación específica. Si este equipo genera interferencia perjudicial en la recepción de radio o televisión, lo cual se puede determinar apagando y encendiendo el equipo, se sugiere que el usuario intente corregir la interferencia mediante una o más de las siguientes medidas: · Mover o reorientar la antena receptora. · Aumentar la separación entre el equipo y el receptor. · Conectar el equipo a una salida o circuito distinto al que está conectado el receptor. · Consultar al proveedor o a un técnico de radio o televisión con experiencia para que le ayuden. El dispositivo ha sido evaluado para que cumpla con los requisitos generales de exposición a RF. El dispositivo se puede usar en condiciones de exposición portátil sin restricciones. FCC ID: YJW-11139PG pure-gear.com © 2024 | F00230PG | 65028PG | 65029PG