Installation (Continued)

6 To link more lights

Attention: Max linkage is 10 units. Only connect to the lights of the same series. Only ONE light is allowed to receive main power input from supply circuit. Otherwise, it will cause damage or fire.

1. Turn off the power of the light and remove the front cover.

   Diagram Description: Shows the fixture with arrows indicating the removal of the front cover.

2. Remove the side cover and release the linking cord from the clamp inside the light compartment.

   Diagram Description: Shows the fixture with the side cover removed, revealing the linking cord clamped inside. Arrows indicate removal of the side cover and release of the cord.

3. Extend the cord to a desired length and insert the cord into the connector of the next light.

   Diagram Description: Shows two light fixtures linked by a cord. An arrow shows the cord extending from one fixture and being inserted into the connector of the next.

4. Place the extra cord back into the clamp and re-attach the front cover.

   Diagram Description: Shows the linking cord placed back into the clamp and the front cover being re-attached to the fixture.

Notes on Linking and Dimmers:

These fixtures are dimmable and compatible with specific dimmers sold at The Home Depot.

• Make sure the lights are in a single loop and a single pole with the dimmers.
• Ensure the total wattage of the lights does not exceed the dimmer wattage capacity. Refer to dimmer packaging for details.
• Contact customer service for further questions on lights or dimmers.

Compatible Dimmers:

• Lutron: DVCL-153PR-WH/396508; CTCL-153PDH-WH/267858; TGCL-153PH-WH/527401; P-PKG1W-WH-R/1000027680
• Leviton: R62-06674-P0W/125569; R60-IPL06-10M/976708

Product Description

Components:

• ON/OFF Switch
• CCT Change Button
• Connector
• Lumin Zone
• Knock-outs

Beam Angle: 110°

Specifications

Safety Information

Carefully read and understand this manual before installation. Failure to do so could lead to electric shock or a fatal hazard.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING: This product must be installed in accordance with applicable installation codes by a qualified person familiar with the product and its hazards.

WARNING: This equipment complies with FCC Rules Part 15 and IC Rules ICES-005. It generates and can radiate radio frequency energy. If not installed and used correctly, it may cause harmful interference. If interference occurs, try to correct it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to a different outlet and circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

CAUTION: This is a non-replaceable LED light source. Do not dismantle the fixture. No user-serviceable parts inside.

CAUTION: For indoor and dry location use only.

CAUTION: Do not touch the fixture when the light source is ON.

CAUTION: Ensure electricity is shut off before installation or work. Remove fuse or turn off circuit breaker.

CAUTION: Deviation from assembly instructions may result in fire or electric shock.

CAUTION: Do not operate with a missing or damaged cover or housing.

CAUTION: Do not mount near a heat source as it may damage the fixture.

CAUTION: Do not stare directly into the LED light.

Limited Warranty

The manufacturer warrants this product to be free from defects in materials and workmanship for five (5) years from the date of purchase. This warranty applies only to the original consumer purchaser and to products used in normal service. If the product is found to be defective, the manufacturer's sole obligation and your exclusive remedy is repair or replacement at the manufacturer's discretion, provided the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty does not apply to products improperly installed, set up, or used contrary to instructions. It also does not apply to failures resulting from accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not related to faulty material or workmanship. The manufacturer disclaims liability for any consequential or incidental loss or damage, including labor/expense costs for replacement or repair.

Contact Customer Service at 1-877-527-0313 or visit www.HomeDepot.com.

Pre-Installation

PLANNING INSTALLATION

Compare all parts with the "Hardware Included" and "Package Contents" sections. If any part is missing or damaged, do not install. Contact customer service.

Tools Required:

• Phillips screwdriver
• Straight screwdriver

Package Contents

Note: Hardware not shown to actual size.

Installation

1. Preparing the light for installation

   Remove two screws on the front of the fixture for access to the wiring compartment. IMPORTANT: Keep these screws; they are needed to install the front cover. No additional screws are provided.

   Diagram Description: Shows the fixture with arrows pointing to the two screws on the front that need to be removed.

2. Preparing the light for installation (continued)

   1. Determine the electrical feed location.
   2. Remove a knockout from either the back or side of the fixture housing. The fixture has two to four knockouts depending on its length.

   Diagram Description: Shows the fixture housing with a knockout being removed from the side.

3. Connecting the wires

   1. Connect the ground wire from the fixture to the ground wire from the supply circuit using the wire connector (B).
   2. Connect the white wire (Neutral wire) from the supply circuit to the blue input (N) of the connector (A) inside the light.
   3. Connect the black wire (Live wire) from the supply circuit to the green input (L) of the connector (A) inside the light.

   CAUTION: Ensure the white and black wires are copper, 14-20AWG. Ensure all wire threads are properly connected.

   NOTE: Before connecting wires, ensure the ON/OFF switch on the surface is OFF to prevent potential risk.

   Diagram Description: Shows wire connections: Ground wire to ground wire connector. White wire to the blue 'N' terminal inside connector A. Black wire to the green 'L' terminal inside connector A.

4. Mounting the light fixture

   Note: The fixture mounting screws are suitable for cabinet bottoms 3/8 in. or thicker. Use shorter screws for thinner cabinet bottoms.

   Attach the light to the desired surface using the fixture mounting screws (C). Tighten the screws securely.

   Diagram Description: Shows the light fixture being attached to a cabinet surface using screws (C). Arrows indicate the fixture being mounted.

5. Re-attach the front cover

   Re-attach the front cover back to the light fixture with the two previously-removed screws. Restore power to the electrical circuit at the service panel. Turn on the switch to light the fixture.

   NOTE: Ensure the wires are covered properly inside the fixture.

   Diagram Description: Shows the front cover being re-attached to the fixture with screws.

Customer Service Contact Information

Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service:

8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m. Saturday.

Phone: 1-877-527-0313

Website: HOMEDEPOT.COM

THANK YOU

We appreciate the trust and confidence you have placed in Commercial Electric. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!