SYNCO | Branded Microphone Manufacturer
User Manual for SYNCO models including: Xtalk XPro Full Duplex Wireless Intercom Headset System, Xtalk XPro, Full Duplex Wireless Intercom Headset System, Duplex Wireless Intercom Headset System, Wireless Intercom Headset System, Intercom Headset System, Headset System
Oct 5, 2024 — 1)Set 2 Masters, 4 Level 1. 2)Pairing (* Please pair and restart each group before pairing the next.). 2-Person Group：. Long press the button A on a Master ...
File Info : application/pdf, 15 Pages, 5.05MB
DocumentDocumentXtalk XPro Full Duplex Wireless Intercom Headset System User Manual Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein. Contents P 01 // Product Introduction P 01 // Button Function P 02 // Operations P 02 // 1. Power On/Off P 03 // 2. Master/Level 1 Settings P 03 // 3. Pairing/Unpairing P 05 // 4. Group Management P 07 // 5. Volume Settings P 07 // 6. Noise Cancellation P 07 // 7. Mute/Unmute P 07 // 8. Dominant Mode P 08 // 9. Boost Mode P 08 // 10. Real-Time Monitoring P 08 // 11. Powering P 09 // 12. Indicator Light Status P 09 // Specifications P 10 // Packing List P 11 // Care Guide P 11 // Warranty Product Introduction 3.5mm Mic In Port Power On/Off Toggle Indicator Light Button A Volume & Headset Settings Verification button Button B Volume Type-C Port Button Function Button A Pairing/Unpairing Set as the Master/Level 1 Button B Noise Cancellation on/off Turn on the Dominant Mode(Only For Master) Volume Volume Up Indicate whether the headset is Master, Level 1 www.syncoaudio.com 1 Volume Volume Down Switch among Boost Mode 1/2/3(Only For Master) Operations 1. Power On/ Off Power On: Push the power toggle switch upwards to turn it on. Power Off: Push the power toggle switch downwards to turn it off. *Products are pre-paired from the factory (except X1) and ready to use. Power On Power Off *To ensure a successful auto-reconnect, please turn on the headsets in the sequence of Master Level 1. Turn on the Master (The red-labeled headset is set as the default Master from the factory) Turn on the Level 1 (The blue-labeled headset with LV.1 sticker is set as the default Level 1 from the factory) www.syncoaudio.com 2 2. Master/Level 1Settings All headsets can be set as: Master/Level 1 Set as Master Long press the button A, release after the 2nd "Beep" sound and hear "Master Mode". Beep, Beep Release Master Mode Set as Level 1 Long press the button A, release after the 3rd "Beep" sound and hear "Level 1 Pairing". Beep, Beep , Beep Release 3. Pairing/Unpairing 1) Set a Master and 1~4 Level 1. Level 1 Pairing Master Mode Level 1 Pairing 2) Long press the button A on all headsets in 1 min, release after the 1st "Beep" sound, and hear "Connecting and Pairing". Master Level 1 Connecting and Pairing Connecting and Pairing www.syncoaudio.com 3 Level 1 Level 1 3) Restart all headsets to use. Master Master Level 1 Level 1 Level 1 3.3 Unpairing Long press the button A, release after the 1st "Beep" sound, and hear "Unpairing". Unpairing www.syncoaudio.com 4 4. Group Management You can divide an Xtalk system into independent groups or merge multiple groups into one single group. 4.1 Divide Into Groups 1)Set the required number of Master based on the planned group count (see 2. Master Settings). 2)Set the Level 1 for each group (see 2. Level 1 Settings ). 3)Pair and restart each group one by one (see 3. Pairing/Unpairing). EG. Divide XPro5 into 2 groups: 2-Person Group & 3-Person Group 1)Set 2 Masters, 4 Level 1. 2)Pairing (* Please pair and restart each group before pairing the next.). 2-Person Group Long press the button A on a Master and a Level 1, release after the 1st "Beep" sound and hear "Connecting and Pairing", then restart the headsets. (Power On Sequence: Master Level 1) 3-Person Group Long press the button A on a Master and 2 Level 1, release after the 1st "Beep" sound and hear "Connecting and Pairing", then restart the headsets. (Power On Sequence: Master Level 1) XPro5 2-Person Group 3-Person Group Master Level 1 www.syncoaudio.com 5 4.2 Combine Into One Group 1) Only keep one Master, and set the other headsets as Level 1 if needed. (See 2. Master/ Level 1 Settings). 2)Pair all headsets and restart (see 3. Pairing/Unpairing). EG. Combine 2 groups(A 2-Person Group and A 3-Person Group) into 1 group 1)Keep 1 Master, set 4 Level 1 (See 2. Master/Level 1 Settings). 2)Pair headsets in sequence: Pair Master with Level 1 (See 3. Pairing/Unpairing). 3)Restart all headsets after successfully connecting(Power on sequence: Master Level 1). 3-Person Group 2-Person Group Master Level 1 Master 5-Person Group Level 1 www.syncoaudio.com 6 5. Volume Settings Short press the volume up/down button to increase/decrease the volume. 6. Noise Cancellation Short press the B button to turn on/off the noise cancellation feature. 7. Mute/Unmute Rotate the boom arm up/down (see the picture below) to mute/unmute. Mute Unmute Unmute 8. Dominant Mode Press and hold the button B of Master to enter the dominant mode for muting other headsets. Other headsets are still available for listening and only the Master is available for speaking. Release the button B to exit dominant mode. Press and hold Master Release Level 1 Master www.syncoaudio.com 7 Level 1 9. Boost Mode When poor signal, switch the Boost Mode to amplify the signal, improving communication clarity and stability, and reducing interruptions and disconnections. Long press the volume-, release after the 1st "Beep" sound to switch the mode and hear "Mode 1/Mode 2/Mode 3". *The operation is only available by Master. * Mode 2 by default. *After changing the Mode, if Level 1 is restarted, please pair it with the upper-level headset again to rejoin the communication group. Beep Release Boost Mode 2 Boost Mode 1 Boost Mode 2 10. Real-Time Monitoring Connect the device(Camera, Camcorder, etc.) with the Xtalk headset via 3.5mm TRS port for monitoring the audio from the device. *This port is only for monitoring and is not the outputting port. 11. Powering Via Replaceable Battery Power Push down the toggle of the battery case then pull the case door outward to place/remove the battery. www.syncoaudio.com 8 12. Indicator Light Status Green Light Steady Green Light Flashing Slow Green/Yellow Lights Alternating Red Light Flashing Slow Red Light Steady Connection Successful Not Connected Noise Cancellation Off Low Battery Charging Specifications Wireless Technology Transmission Mode Operating Range Frequency Band Latency Approximate RF Sensitivity Radio Output Frequency Power Battery Capacity Working Time Charging Time Frequency Response Signal-To-Noise Ratio Distortion Microphone Type Max Input Sound Pressure Level Output Sound Pressure Level Weight Temperature Range Digital 2.4GHz Full-Duplex 500m (LOS) 2.4GHz About 120ms <-90dBm 20dBm USB-C 5V 1050mAh Li-ion Battery 24H About 2.5H 150Hz~7KHz 65dB <1 % Condenser Microphone >115dBSPL Typical 98+3dBSPL(at 94dBSPL 1KHz) About 188gBattery Included 0~+45° C(Working Status -20~+60° C(Storage Condition) www.syncoaudio.com 9 Packing List XPro1 Headset x1 Charging Cable x1 Carrying Bagx1 Rechargeable Battery x1 One-Ear Foam Cushion x1 XPro2 Mic Windshield x1 Warranty Card x1 Headset x2 Charging Cable x1 Carrying Bag x2 Charging Station x1 One-Ear Foam Cushion x2 Mic Windshield x2 Rechargeable Battery x2 Warranty Card x1 www.syncoaudio.com 10 XPro5 Headset x5 Storage Bag x1 Charging Station x3 Charging Cable x3 Carrying Bag x5 Rechargeable Battery x5 One-Ear Foam Cushion x5 Mic Windshield x5 Warranty Card x1 Caring For Your SYNCO Product · Please keep the product in a dry, clean, dust-free environment. · Keep corrosive chemicals, liquids, and heat sources away from the product to prevent mechanical damage. · Use only a soft and dry cloth for cleaning the product. · Malfunction may be caused by dropping, the impact of external force. · Do not attempt to disassemble the product. Doing so voids the warranty. · Please have the product checked or repaired by authorized technicians if any malfunctions happen. · Failure to follow all the instructions may result in mechanical damage. · Warranty does not apply to human errors. WARRANTY Warranty Period Thank you for purchasing SYNCO products. 1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product. 2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee). www.syncoaudio.com 11 Warranty Exclusions and Limitations 1. Faults resulted from inappropriate use of a product without following its operation specification 2. Artificial damage, e.g. crash, squeeze, scratch, or soaking 3. Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration 4. The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off 5. All consumable accessory attached to a product, like cable, wind muff, battery 6. Faults as a result of force majeure, such as fire, flood, lightning, etc. Warranty Claim Procedure 1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO's customer service through email at support@syncoaudio.com. 2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. 3. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged. www.syncoaudio.com 12 Guangzhou Zhiying Technology Co., Ltd Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000 support@syncoaudio.com www.syncoaudio.com https://www.facebook.com/syncomicrophones