ASSA ABLOY Group - global leader in access solutions | ASSA ABLOY
P65warnings.ca.gov
Instruction Manual for SARGENT models including: 988, 988CR, 988Y, 988 Surface Bolt, Surface Bolt, Bolt
Sargent ation
23 giu 2023 — INSTALLATION PROCEDURE. 1. Strike Mounting: • Determine if bolt is to be mounted at top. (1-1) or bottom (1-2) of door. • A 2 ¾ " backset is recommended.
File Info : application/pdf, 1 Pages, 101.25KB
DocumentDocumentInstallation Instructions 988 / 988CR / 988Y Surface Bolt INSTALLATION PROCEDURE 1. Strike Mounting: ¼" · Determine if bolt is to be mounted at top (1-1) or bottom (1-2) of door. · A 2 ¾" backset is recommended. 1-1. Top of Door (frame mounted strike): · Locate strike on frame as shown and mark hole locations. For Windstorm Strike, fac tory frame preparation is supplied. · Drill and tap for ¼" 20 machine screws (#8 drill and ¼" 20 tap are required). · Secure strike with three (3) ¼" 20 x ¾ " screws (supplied). 1" Grommet Nut 1-2. 7diidbd[9ddgÓddgbdjciZYhig^`Z/ · 1-1/8" dia. x 1½" deep hole required in floor to accept surface bolt. · Mark and drill two (2) 7/16" dia. x 1¼ " deep holes for strike anchors. · Securestrikewithtwo(2)anchorsand¼" 20 x ¾ " screws (supplied). Hole (prepared by door mfg.) 2. Surface Bolt Mounting: · Slide knob end retainer to stop pin. · Locate surface bolt and retainers on door as shown. Mark location of through-bolts. · Check bolt alignment in strike before drilling holes. · Drill four (4) 9/32" dia. holes through door. · Open holes for grommet nuts on opposite side of door using "V" size drill. · Secure retainers to door using grommet nuts and ¼" 20 x 2-3/4 " screws (supplied). · Check for proper operation. ¼" 1" Grommet Nut WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65warnings.ca.gov. TOP OF DOOR MOUNTING (1-1) FRAME STOP MOUNTING (PUSH SIDE) FRAME SURFACE MOUNTING (PULL SIDE) ¼" Screw (3 Req'd) Angle Strike Retainer Assembly Screw (4 Req'd) Stop Pin 1- 3/8" Surface Bolt BOTTOM OF DOOR MOUNTING (1-2) Knob Lock Hole Throw 1¼" 1- 3/8" Flat Mortise Strike 1/8" FRAME STOP MOUNTING (PUSH SIDE) WINDSTORM FRAME RABBET MOUNTING (PULL SIDE) WINDSTORM Windstorm 9 Strike ¼" Concrete Floor Screw (2 Req'd) Anchor (2 Req'd) Retainer Assembly Stop Pin Screw (4 Req'd) 1- 3/8" Surface Bolt Item Description Qty. 1 Retainer 2 2 Surface Bolt 1 3 Flat Mortise Strike 1 4 Angle Strike 1 5 Screw, ¼20 x 2-3/4" 4 6 Grommet Nut 4 7 Screw, ¼20 x ¾" 3 8 Anchor 2 9 Windstorm Strike 1 NOTE: Parts used depend on mounting application. 1-800-438-1951 · www.assaabloy.com MEMN8 3/23 Copyright © 2017, 2022, 2023, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.