Super Bright LEDs DS-SC Addressable RGB LED Controller and Remote User Manual

Important: Read all instructions prior to installation.

Safety and Notes

Product should be installed and serviced in accordance with applicable national, state, and local building and electrical codes.
To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.

Example Wiring Diagram

A diagram shows the DS-SC controller connected to a power supply and an addressable RGB strip. The controller has inputs for power and data/clock, and outputs for data/clock. The power supply connects to the controller's power input. The addressable RGB strip connects to the controller's data and clock outputs.

Pairing Remote(s)

REMOTE(S) MUST BE PAIRED AS PART OF THE INSTALLATION PROCESS AND DO NOT COME PRE-PAIRED. EACH CONTROLLER CAN BE PAIRED TO UP TO TEN (10) REMOTES.

To pair a remote, press the match button on the controller, then immediately press the on/off button on the remote. The indicator light on the controller will flash slowly while attempting to pair, then flash five times rapidly to indicate successful pairing.

To unpair a remote, hold the match button for five seconds. The indicator light on the controller will flash five times rapidly to indicate successful unpairing.

Remote Layout and Functions

The remote control has buttons for:

RGB channel adjustment
Speed: Adjusts the speed of the selected preprogrammed mode. Hold the upper speed button for two seconds for the fastest speed. Hold the lower speed button for two seconds for the slowest speed.
Mode: Cycles through preprogrammed modes. Hold the upper mode button for two seconds to run the mode cycle demo. Hold the lower mode button for two seconds to return to and run mode 1.
Brightness: Adjusts brightness in ten percent increments. Hold for continuous 256 level adjustment.
RGB: Adjusts color in ten percent increments. Hold for continuous 256 level adjustment.
White: Turns white (RGB mix) on/off. Hold for continuous 256 level adjustment.
Scene: Saves current settings by holding the scene button for two seconds. Recalls saved settings by pressing the scene button.
Numbered buttons (1-10) for specific colors and white.

Color key for numbered buttons: 1: red, 2: green, 3: blue, 4: yellow, 5: magenta, 6: cyan, 7: orange, 8: purple, 9: light green, 10: natural white

Setting Adjustment

Strip Length (Pixel Number) Setting

Strip length, or pixel number, can be set up to 1,024 pixels. Begin by pressing the function button (*), then entering the number of pixels with the number buttons, then pressing the function (*) button again. Note: Numbers lower than 100 will need a zero (0) entered in before the number.

RGB Order

RGB order can be set by pressing the function button (*), then entering the one-digit code corresponding with the correct RGB order using the number pad, then pressing the function (*) button again.

Code	RGB Order
1	RGB
2	RBG
3	GRB
4	GBR
5	BRG
6	BGR

IC Type Setting

IC type can be set by pressing the function button (*), then entering the two-digit code corresponding with the correct IC type using the number pad, then pressing the function (*) button again. Consult the list below for the code for each IC type.

Code	IC Type
11	TM1803
12	TM1809, TM1804, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812
13	TM1829
14	TLS3001, TLS3002
15	GW6205
16	MBI6120
17	TM1814B(RGBW)
18	SK6812(RGBW)
19	UCS8904B(RGBW)
21	LPD6803, LPD1101, D705, UCS6909, UCS6912
22	LPD8803, LPD8806
23	WS2801, WS2803
24	P9813
25	SK9822
31	TM1914A

Preprogrammed Modes

Once remote is paired, hold the upper mode (mode plus) button for 2 seconds to unlock preprogrammed modes which can then be cycled through using the mode buttons on the remote.

No.	Name	No.	Name	No.	Name
1	Red Race White Ground	12	Blue White Chase	23	Purple Float
2	Green Race White Ground	13	Green Cyan Chase	24	RGBW Float
3	Blue Race White Ground	14	RGB Chase	25	Red Yellow Float
4	Yellow Race Blue Ground	15	7-color Chase	26	Green Cyan Float
5	Cyan Race Blue Ground	16	Blue Meteor	27	Blue Purple Float
6	Purple Race Blue Ground	17	Purple Meteor	28	Blue White Float
7	7 Color Multi Race	18	White Meteor	29	6 Color Float
8	7 Color Race Close + Open	19	7 Color Meteor	30	6 Color Smooth Sectionally
9	7 Color Multi Race Close + Open	20	Red Float	31	7 Color Jump Sectionally
10	7 Color Scan Close + Open	21	Green Float	32	7 Color Strobe Sectionally
11	7 Color Multi Scan Close + Open	22	Blue Float

Rev Date: V2 12/07/2020
4400 Earth City Expy, St. Louis, MO 63045 • 866-590-3533 • superbrightleds.com

	MiBoxer 2.4 GHz Wi-Fi Multi Zone RGBW Controller and Remote User Manual Comprehensive user manual for the MiBoxer LDRF-RGB-MZ 2.4 GHz Wi-Fi Multi Zone RGBW LED Controller and MZ-RGB-REMOTE touch color remote. Includes installation, operation, pairing, specifications, and safety guidelines from Super Bright LEDs.
	Super Bright LEDs MCBRF-RGBW RGBW LED Controller User Manual User manual for the Super Bright LEDs MCBRF-RGBW RGBW LED Controller with Wireless RF Remote, detailing installation, functions, operation, safety precautions, and technical specifications.
	Superbrightleds GL-C-001W RGB/CCT/RGBW/RGBCCT LED Controller User Manual Detailed user manual for the Superbrightleds GL-C-001W LED controller, covering installation, wiring, Wi-Fi pairing, remote control, and preprogrammed modes for RGB, CCT, RGBW, and RGBCCT LED strips.
	Super Bright LEDs RGB+CCT Controller Module User Manual User manual for the Super Bright LEDs RGBCCT6-MZ RGB+CCT Controller Module, including specifications, control features, and instructions for Wi-Fi and wireless remote control.
	Super Bright LEDs DMX-24CH-LV DMX Decoder User Manual User manual for the Super Bright LEDs DMX-24CH-LV DMX Decoder, detailing setup, specifications, product dimensions, and warranty information for controlling LED lights with DMX512 signals.
	Super Bright LEDs EZD-RGBW3-WM Wireless RGBW 3-Zone Wall Switch User Manual User manual for the Super Bright LEDs EZD-RGBW3-WM Wireless RGBW 3-Zone Wall Switch, detailing installation, pairing, controller setup, and remote functions for EZ Dimmer Series Controllers.
	SuperbrightLEDs MCB-RGB-DC99 Color Chasing RGB LED Controller User Manual Comprehensive user manual for the SuperbrightLEDs MCB-RGB-DC99 Color Chasing RGB LED Controller. Includes setup, remote functions, connection methods, program lists, specifications, and safety information.
	Super Bright LEDs Wireless LED Dimmer Push Button Switch (EZD-1C-PB) Installation Guide Learn how to install and operate the Super Bright LEDs EZD-1C-PB Wireless LED Dimmer Push Button Switch with EZ Dimmer Series Controllers (EZD-4C8A, EZD-1C8A). This guide covers pairing, setup, safety, and wiring diagrams for efficient LED lighting control.