ELECTRONICS Click here for: Radar Installation Guides 2011-2014 Chrysler 200 INSTALL GUIDE RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE!
Idatalink Maestro Rr Kenwood Error › Url: http://images.idatalink.com/corporate/Content/Manuals/RR-CHR/ADS-RR(SR)-CHR01-DS-IG-EN 20191015
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or "quick printing" this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE 2011-2014 Chrysler 200 RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler 200 2011-2014 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler 200 2011-2014 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Chrysler 200 2011-2014 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler 200 2011-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler 200 2011-2014 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2010 Chrysler 300 RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler 300 2008-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler 300 2008-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Chrysler 300 2008-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler 300 2008-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler 300 2008-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2009 Chrysler Aspen RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler Aspen 2008-2009 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler Aspen 2008-2009 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Chrysler Aspen 2008-2009 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler Aspen 2008-2009 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler Aspen 2008-2009 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2007-2010 Chrysler Sebring RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler Sebring 2007-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler Sebring 2007-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Chrysler Sebring 2007-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler Sebring 2007-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler Sebring 2007-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2011 Chrysler Town And Country RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler Town And Country 2008-2011 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler Town And Country 2008-2011 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Chrysler Town And Country 2008-2011 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler Town And Country 2008-2011 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler Town And Country 2008-2011 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2012-2016 Chrysler Town And Country RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Chrysler Town And Country 2012-2016 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Chrysler Town And Country 2012-2016 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Chrysler Town And Country 2012-2016 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Chrysler Town And Country 2012-2016 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Chrysler Town And Country 2012-2016 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2014 Dodge Avenger RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Avenger 2008-2014 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Avenger 2008-2014 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Avenger 2008-2014 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Avenger 2008-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Avenger 2008-2014 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2009-2012 Dodge Caliber RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Caliber 2009-2012 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Caliber 2009-2012 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Caliber 2009-2012 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Caliber 2009-2012 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Caliber 2009-2012 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2014 Dodge Challenger RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Challenger 2008-2014 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Challenger 2008-2014 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Challenger 2008-2014 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Challenger 2008-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Challenger 2008-2014 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2010 Dodge Charger RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Charger 2008-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Charger 2008-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Charger 2008-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Charger 2008-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Charger 2008-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2010 Dodge Dakota RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Dakota 2008-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Dakota 2008-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Dakota 2008-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Dakota 2008-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Dakota 2008-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2011 Dodge Dakota RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Dakota 2011 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Dakota 2011 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) STEP 6 MAIN HARNESS SEE RADIO WIRE REFERENCE CHART STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE Dodge Dakota 2011 CONNECT TO AFTERMARKET RADIO DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Dakota 2011 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Dakota 2011 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2009 Dodge Durango RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Durango 2008-2009 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Durango 2008-2009 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Dodge Durango 2008-2009 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Durango 2008-2009 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Durango 2008-2009 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2011-2013 Dodge Durango RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Durango 2011-2013 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Durango 2011-2013 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Durango 2011-2013 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Durango 2011-2013 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Durango 2011-2013 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2011 Dodge Grand Caravan RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Grand Caravan 2008-2011 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Grand Caravan 2008-2011 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Grand Caravan 2008-2011 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Grand Caravan 2008-2011 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Grand Caravan 2008-2011 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2012-2019 Dodge Grand Caravan RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Grand Caravan 2012-2019 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Grand Caravan 2012-2019 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Grand Caravan 2012-2019 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Grand Caravan 2012-2019 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Grand Caravan 2012-2019 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2009-2010 Dodge Journey RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Journey 2009-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Journey 2009-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Journey 2009-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Journey 2009-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Journey 2009-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2007-2011 Dodge Nitro RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Nitro 2007-2011 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Nitro 2007-2011 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Nitro 2007-2011 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Nitro 2007-2011 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Nitro 2007-2011 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2010-2015 Dodge Ram CV RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Dodge Ram CV 2010-2015 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Dodge Ram CV 2010-2015 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Dodge Ram CV 2010-2015 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Dodge Ram CV 2010-2015 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Dodge Ram CV 2010-2015 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2010 Jeep Commander RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Commander 2008-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Commander 2008-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Jeep Commander 2008-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Commander 2008-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Commander 2008-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2009-2016 Jeep Compass RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Compass 2009-2016 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Compass 2009-2016 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Jeep Compass 2009-2016 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Compass 2009-2016 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Compass 2009-2016 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2010 Jeep Grand Cherokee RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Grand Cherokee 2008-2010 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Grand Cherokee 2008-2010 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Jeep Grand Cherokee 2008-2010 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Grand Cherokee 2008-2010 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Grand Cherokee 2008-2010 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2011-2013 Jeep Grand Cherokee RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Grand Cherokee 2011-2013 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Grand Cherokee 2011-2013 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Jeep Grand Cherokee 2011-2013 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Grand Cherokee 2011-2013 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Grand Cherokee 2011-2013 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2012 Jeep Liberty RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Liberty 2008-2012 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Liberty 2008-2012 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Jeep Liberty 2008-2012 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Liberty 2008-2012 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Liberty 2008-2012 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2009-2016 Jeep Patriot RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Patriot 2009-2016 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Patriot 2009-2016 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Jeep Patriot 2009-2016 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Patriot 2009-2016 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Patriot 2009-2016 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2007-2018 Jeep Wrangler JK AT RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Wrangler JK AT 2007-2018 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Wrangler JK AT 2007-2018 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Jeep Wrangler JK AT 2007-2018 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Wrangler JK AT 2007-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Wrangler JK AT 2007-2018 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2007-2018 Jeep Wrangler JK MT RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Jeep Wrangler JK MT 2007-2018 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Jeep Wrangler JK MT 2007-2018 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · To connect reverse camera, connect PURPLE/WHITE Reverse Light (+) wire from aftermarket radio to White/ Gray wire in harness in passenger kick panel. STEP 8 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 3 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE (NC) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Jeep Wrangler JK MT 2007-2018 STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO SEE RADIO WIRE REFERENCE CHART STEP 4 FACTORY RADIO HARNESS STEP 7 PURPLE/WHITE REVERSE LIGHT (+) DATA CABLE AUDIO CABLE PASSENGER KICK PANEL WHITE/GRAY OBDII CONNECTOR WIRES FROM VEHICLE STEP 8 MAESTRO RR MODULE Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Jeep Wrangler JK MT 2007-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Jeep Wrangler JK MT 2007-2018 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2009 Mitsubishi Raider RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Mitsubishi Raider 2008-2009 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Mitsubishi Raider 2008-2009 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female RED connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 2 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE RED BLACK STEP 3 BLACK (NC) Mitsubishi Raider 2008-2009 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Mitsubishi Raider 2008-2009 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Mitsubishi Raider 2008-2009 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2009-2012 Ram Pickup RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Ram Pickup 2009-2012 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Ram Pickup 2009-2012 INSTALLATION INSTRUCTIONS Note: VES cannot be retained in this vehicle. STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. Automotive Data Solutions Inc. © 2019 4 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Ram Pickup 2009-2012 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Ram Pickup 2009-2012 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Ram Pickup 2009-2012 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2008-2011 Volkswagen Routan RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Volkswagen Routan 2008-2011 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Volkswagen Routan 2008-2011 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Volkswagen Routan 2008-2011 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Volkswagen Routan 2008-2011 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Volkswagen Routan 2008-2011 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.com INSTALL GUIDE 2012-2014 Volkswagen Routan RETAINS STEERING WHEEL CONTROLS, UCONNECT, UCONNECT BLUETOOTH, AND MORE! OR PRODUCTS REQUIRED iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro CH1 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-CHR01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Troubleshooting Table Volkswagen Routan 2012-2014 3 4 5 6 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 2 maestro.idatalink.com Volkswagen Routan 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the CH1 T-harness and match the wire functions. STEP 2 · Remove the factory radio. · Access the main 22 pin factory radio connector (2.1) and determine if you have a factory amplifier. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Fig. 2.1 If you don't have wires in PIN 19, 20, 21 and 22, you have a factory amplifier: · Plug the female GREEN connector to the male GREEN connector of your CH1 T-harness. · Plug the female WHITE connector to the male WHITE connector of your CH1 T-harness. If you have wires in PIN 19, 20, 21 and 22, you don't have a factory amplifier: · Plug the female GREEN connector to the male WHITE connector of your CH1 T-harness. · Plug the female WHITE connector to the male GREEN connector of your CH1 T-harness. STEP 3 · Plug the female BLACK connector to the male BLACK connector. STEP 4 · Connect the factory harness to the CH1 T-harness. STEP 5 · Access the OBDII connector located under the driver side dashboard. · Connect the RED/BROWN wire of the CH1 T-harness to the wire located at pin 6 of the OBDII connector. (See the vehicle wire chart reference for wire colors) · Connect the YELLOW/BROWN wire of the CH1 T-harness to the wire located at pin 14 of the OBDII connector. (See the vehicle wire chart reference for wire colors) STEP 6 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. · Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 7 · Connect all the harnesses to the Maestro RR module then test your installation. Automotive Data Solutions Inc. © 2019 1 ADS-RR(SR)-CHR01-DS-IG-EN 3 maestro.idatalink.com WIRING DIAGRAM STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BROWN (NOT CONNECTED) YELLOW/BLACK - FOOT BRAKE STEP 2 CONNECTIONS WITHOUT AMP GREEN WHITE WHITE GREEN CONNECTIONS WITH AMP GREEN GREEN WHITE WHITE BLACK BLACK STEP 3 RED (NC) Volkswagen Routan 2012-2014 SEE RADIO WIRE REFERENCE CHART STEP 6 MAIN HARNESS CONNECT TO AFTERMARKET RADIO STEP 4 FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE AUDIO CABLE STEP 5 CH1 T-HARNESS NOT REQUIRED STEERING WHEEL CONTROL CABLE Automotive Data Solutions Inc. © 2019 OBDII CONNECTOR STEP 7 MAESTRO RR MODULE ADS-RR(SR)-CHR01-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Volkswagen Routan 2012-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood Wire Color on Pioneer cable cable Wire Color on Sony cable Illumination (+) Reverse Light (+) E-Brake (-) Foot Brake (+) VSS (vehicle speed sensor) (DATA) Orange Purple/White Lt Green Yellow/Black Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A Pink Orange/White Purple/White Lt Green N/A Pink Orange Purple/White Lt Green N/A N/A Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 5 maestro.idatalink.com TROUBLESHOOTING TABLE Volkswagen Routan 2012-2014 PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the BROWN/RED wire is on PIN 6 and the BROWN/ YELLOW wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. Switch the 4-pin green and white connectors in the t-harness. The radio stays ON or the radio doesn't come ON at all. Make sure the 2-pin black and red connectors in the harness are connected correctly as stated in step 2. There isn't a connector in the dash for the 10 pin gray plug of the t-harness. That is fine. Not every vehicle will have it, and it's not essential for proper radio operation. The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module. The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-CHR01-DS-IG-EN 6 maestro.idatalink.comAdobe InDesign CC 2015 (Macintosh) Adobe PDF Library 15.0