Kingston Bathroom Accessory Installation Guides
Comprehensive instructions for installing various Kingston bathroom fixtures.
Towel Bar Installation Instructions
Product: Towel Bar
Tools Required
- Phillips Screwdriver
- Flathead Screwdriver
- Pencil
- Hammer
- Power Drill
Parts Included
- Mounting Plate (2 Pcs)
- Mounting Screw & Anchor (4 Pcs)
- Slotted Set Screw (2 Pcs)
Company Information:
Website: www.kingstonbrass.com
Customer Service: TOLL-FREE 1-877-2-KBRASS
Technical Support: service@kingstonbrass.com
Address: 12775 Reservoir Street, Chino, CA 91710
⚠️ CAUTION: Failure to follow all installation directions may cause product to detach from the wall and cause serious injury.
Installation Steps
- Step 1: Locate desired installation position. Place the accessory's base onto the wall and trace its outline with a pencil. (Visual: Tracing the base on the wall.)
- Step 2: Position the mounting plate within the traced outline. Mark the locations for the mounting screws. (Visual: Marking screw holes on the mounting plate.)
- Step 3: Drill holes at the marked locations. (Visual: Drilling holes into the wall.)
- Step 4: Insert wall anchors into the drilled holes until they are flush with the wall. (Visual: Inserting anchors into the wall.)
- Step 5: Secure the mounting plate to the wall using the provided mounting screws. Ensure the plate's lips face outwards. (Visual: Attaching the mounting plate to the wall.)
- Step 6: Align the accessory's base over the mounting plate, ensuring the small hole in the base is underneath. Tighten the slotted set screw with a flathead screwdriver to secure the base firmly to the wall. (Visual: Securing the accessory to the mounting plate with the set screw.)
Cleaning Instructions
Clean with a damp cloth only. Avoid using metal or abrasive polishes.
©2025 LVC Kingston LLC. All Rights Reserved. Document Version: 2025-05-D
Robe Hook Installation Instructions
Product: Robe Hook
Tools Required
- Phillips Screwdriver
- Flathead Screwdriver
- Pencil
- Hammer
- Power Drill
Parts Included
- Mounting Plate (1 Pc)
- Mounting Screw & Anchor (2 Pcs)
- Slotted Set Screw (1 Pc)
Company Information:
Website: www.kingstonbrass.com
Customer Service: TOLL-FREE 1-877-2-KBRASS
Technical Support: service@kingstonbrass.com
Address: 12775 Reservoir Street, Chino, CA 91710
⚠️ CAUTION: Failure to follow all installation directions may cause product to detach from the wall and cause serious injury.
Installation Steps
- Step 1: Locate desired installation position. Place the accessory's base onto the wall and trace its outline with a pencil. (Visual: Tracing the base on the wall.)
- Step 2: Position the mounting plate within the traced outline. Mark the locations for the mounting screws. (Visual: Marking screw holes on the mounting plate.)
- Step 3: Drill holes at the marked locations. (Visual: Drilling holes into the wall.)
- Step 4: Insert wall anchors into the drilled holes until they are flush with the wall. (Visual: Inserting anchors into the wall.)
- Step 5: Secure the mounting plate to the wall using the provided mounting screws. Ensure the plate's lips face outwards. (Visual: Attaching the mounting plate to the wall.)
- Step 6: Align the accessory's base over the mounting plate, ensuring the small hole in the base is underneath. Tighten the slotted set screw with a flathead screwdriver to secure the base firmly to the wall. (Visual: Securing the accessory to the mounting plate with the set screw.)
Cleaning Instructions
Clean with a damp cloth only. Avoid using metal or abrasive polishes.
©2025 LVC Kingston LLC. All Rights Reserved. Document Version: 2025-05-D
Towel Ring Installation Instructions
Product: Towel Ring
Tools Required
- Phillips Screwdriver
- Flathead Screwdriver
- Pencil
- Hammer
- Power Drill
Parts Included
- Mounting Plate (1 Pc)
- Mounting Screw & Anchor (2 Pcs)
- Slotted Set Screw (1 Pc)
Company Information:
Website: www.kingstonbrass.com
Customer Service: TOLL-FREE 1-877-2-KBRASS
Technical Support: service@kingstonbrass.com
Address: 12775 Reservoir Street, Chino, CA 91710
⚠️ CAUTION: Failure to follow all installation directions may cause product to detach from the wall and cause serious injury.
Installation Steps
- Step 1: Locate desired installation position. Place the accessory's base onto the wall and trace its outline with a pencil. (Visual: Tracing the base on the wall.)
- Step 2: Position the mounting plate within the traced outline. Mark the locations for the mounting screws. (Visual: Marking screw holes on the mounting plate.)
- Step 3: Drill holes at the marked locations. (Visual: Drilling holes into the wall.)
- Step 4: Insert wall anchors into the drilled holes until they are flush with the wall. (Visual: Inserting anchors into the wall.)
- Step 5: Secure the mounting plate to the wall using the provided mounting screws. Ensure the plate's lips face outwards. (Visual: Attaching the mounting plate to the wall.)
- Step 6: Align the accessory's base over the mounting plate, ensuring the small hole in the base is underneath. Tighten the slotted set screw with a flathead screwdriver to secure the base firmly to the wall. (Visual: Securing the accessory to the mounting plate with the set screw.)
Cleaning Instructions
Clean with a damp cloth only. Avoid using metal or abrasive polishes.
©2025 LVC Kingston LLC. All Rights Reserved. Document Version: 2025-05-D
Toilet Paper Holder Installation Instructions
Product: Toilet Paper Holder
Tools Required
- Phillips Screwdriver
- Flathead Screwdriver
- Pencil
- Hammer
- Power Drill
Parts Included
- Mounting Plate (2 Pcs)
- Mounting Screw & Anchor (4 Pcs)
- Slotted Set Screw (2 Pcs)
Company Information:
Website: www.kingstonbrass.com
Customer Service: TOLL-FREE 1-877-2-KBRASS
Technical Support: service@kingstonbrass.com
Address: 12775 Reservoir Street, Chino, CA 91710
⚠️ CAUTION: Failure to follow all installation directions may cause product to detach from the wall and cause serious injury.
Installation Steps
- Step 1: Locate desired installation position. Place the accessory's base onto the wall and trace its outline with a pencil. (Visual: Tracing the base on the wall.)
- Step 2: Position the mounting plate within the traced outline. Mark the locations for the mounting screws. (Visual: Marking screw holes on the mounting plate.)
- Step 3: Drill holes at the marked locations. (Visual: Drilling holes into the wall.)
- Step 4: Insert wall anchors into the drilled holes until they are flush with the wall. (Visual: Inserting anchors into the wall.)
- Step 5: Secure the mounting plate to the wall using the provided mounting screws. Ensure the plate's lips face outwards. (Visual: Attaching the mounting plate to the wall.)
- Step 6: Align the accessory's base over the mounting plate, ensuring the small hole in the base is underneath. Tighten the slotted set screw with a flathead screwdriver to secure the base firmly to the wall. (Visual: Securing the accessory to the mounting plate with the set screw.)
Cleaning Instructions
Clean with a damp cloth only. Avoid using metal or abrasive polishes.
©2025 LVC Kingston LLC. All Rights Reserved. Document Version: 2025-05-D
