Smart Tag RSH-iTag 09

Specifications

Getting Started

System Requirements and Compatibility

Requires Apple ID, iPhone and iPod touch models with iOS 14.5 or later, or iPad models with iPadOS 14.5 or later.

Pairing Mode

Pulling out the white tab from the device activates pairing mode.

Connection Methods

Quick Connection

1. Ensure Bluetooth is turned on.
2. Pull out the white tab to activate pairing mode.
3. Scan the provided QR code with your iPhone camera. Tap 'Find My' below the code to enter pairing mode. (Scan the code to watch the operation video)
4. Connect the device.
5. Name the item.
6. Choose a pattern/icon.
7. Agree to terms.
8. Finish the setup.

Manual Connection

1. Open the Apple Find My app and ensure Bluetooth is turned on.
2. Pull out the white tab to activate pairing mode.
3. Select 'Add Item' in the item list.
4. Select 'Other Supported Item'.
5. Ensure the device is powered on.
6. Search for items.
7. Connect the device.
8. Name the item.
9. Choose a pattern/icon.
10. Agree to terms.
11. Finish the setup.

Operation

Power On/Off/Reset

• Power On: Press the button once.
• Power Off: Press and hold the button for 5 seconds.
• Reset: Press the button 4 times quickly within 2 seconds, then press and hold the button for the 5th time until you hear a beep. The device is now in reset state.

Battery Replacement

To replace the battery, use the provided tool to open the device shell.

Important Information

Privacy Tip

If you wish to return the product for a refund, please ensure you remove any added items from the device before returning to avoid disclosing your personal privacy.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

CE/RoHS Notice

Products with the CE marking comply with the Radio Equipment Directive (2014/53/EU). Compliance with these directives implies conformity to the following European Standards: EN IEC 62368-1:2020+A11:2020, EN 62479:2010, EN 50663:2017, ETSI EN 301 489-1 V2.2.3(2019-11), Draft ETSI EN 301 489-17 V3.2.6(2023-06), EN 55032:2015+A1:2020+A11:2020, EN 55035:2017 +A11:2020, ETSI EN 300 328 V2.2.2 (2019-07).

Products with the RoHS marking comply with the RoHS Directive (2015/863/EU) amending Annex II to Directive (2011/65/EU).

Support

For any questions, please contact: support@himojo.net