Tribesigns Assembly Instructions

Important Information

⚠️ When using the electric screwdriver, reduce the power and torque to avoid damaging the furniture.

Read each step carefully before starting. It is very important that each step of instruction is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.

❗ Caution: Make sure all parts are included. Most board parts are labeled or stamped on the raw edge. Contact Tribesigns for a free replacement if you encounter any damaged or missing parts.

Parts List

The following is a list of parts included in the package:

• Part 1: 1 pc
• Part 2: 1 pc
• Part 3: 1 pc
• Part 4: 1 pc
• Part 5: 1 pc
• Part 6: 2 pcs
• Part 7: 1 pc
• Part 8: 1 pc
• Part 9: 1 pc
• Part 10: 1 pc
• Part 11: 1 pc
• Part 12: 1 pc
• Part 13: 1 pc
• Part 14: 1 pc
• Part 15: 1 pc
• Part 16: 1 pc
• Part 17: 1 pc
• Part 18: 1 pc
• Part 19: 1 pc
• Part 20: 1 pc
• Part 21: 2 pcs
• Part 22: 1 pc
• Part 23: 2 pcs
• Part 24: 2 pcs
• Part 25: 2 pcs

Hardware List

The following is a list of hardware included in the package:

Assembly Steps

Step 1

Attach part O (M6XØ23mm) to part 24 (x2).

Step 2

Attach parts L (M6X60mm) and F (M4X64mm) to parts 24 (x2) and 25 (x2).

Step 3

Attach part D (Ø8X30mm) to parts 12, 15, and 13.

Step 4

Attach parts D (Ø8X30mm) and E (Ø7X47mm) to parts 12, 13, 14, and 17.

Step 5

Attach part D (Ø8X30mm) to parts 10, 8, and 9.

Step 6

Attach part A (Ø6X40mm) to part 11. Then, attach parts B (Ø15X12mm) and D (Ø8X30mm) to parts 10, 9, and 11.

Step 7

Attach parts D (Ø8X30mm) and E (Ø7X47mm) to parts 9, 10, and 17.

Step 8

Attach parts K (M6X50mm) to the structure.

Step 9

Attach parts 5, 6, and 6 to the main structure.

Step 10

Attach parts J (M6X40mm) to parts 20, 21, 22, and 19.

Step 11

Attach part O (M6XØ23mm) to part 18.

Step 12

Attach parts L (M6X60mm) to part 18 and 19.

Step 13

Attach parts J (M6X40mm) to the structure.

Step 14

Attach parts I (M6X30mm) to the structure.

Step 15

Attach parts A (Ø6X40mm) to part 7.

Step 16

Attach parts B (Ø15X12mm) and D (Ø8X30mm) to part 7.

Step 17

Attach parts G (3.5X14mm), M (106X16X8mm), N (M4X18mm), and P (M6X25mm) to part 16.

Step 18

Attach parts G (3.5X14mm) to part 16.

Step 19

Attach part 23 to part 3 using part I (M6X30mm).

Step 20

Assemble the main desk structure using parts 1, 2, and 3 with hardware.

Step 21

Attach parts K (M6X50mm) to the structure.

Step 22

Attach part H (M6X25mm) to part 4.

Step 23

Attach parts C (3X18mm) and Q (17x16x10.5) to the structure.

Step 24

The desk is now fully assembled.