eMeetLink Guide

1. Enable or release the screen

Preview the video when adjusting the settings.

[Image: Screenshot of eMeetLink software showing screen preview with options to enable/release screen, adjust zoom, and anti-flicker settings.]

2. Firmware update

In the upper right corner, you can see your device's firmware version. Also, you can click the “Upgrade” button to get the latest version.

Firmware update
Version:V5.0.5/0.3.7

3. Video Mode

1) Easy Switch between 5 modes

There are five conference modes for your choices: Collaboration Mode, Speech Mode, Classic Mode, Spotlight Mode, or InPrivate mode. You can select according to your needs.

• Collaboration Mode: Active speakers (up to 3) can be detected by their voices and appear on the screen at the same time. Their faces will be automatically centered. The lower part of the screen displays a panoramic view of the conference room.
• Speech mode: Only one active speaker will be focused and appear on the screen. The lower part displays a panoramic of the conference room.
• Classic mode: In this mode, the camera records a 180-degree wide-angle video.
• Spotlight mode: Adopting a 65° field of view, this is a mode designed for one-person use.
• InPrivate mode: This mode turns off both the microphones and the camera for privacy protection.

[Image: Screenshot of eMeetLink software showing the Video Mode selection with options for Collaboration Mode, Speech Mode, Classic Mode, Spotlight Mode, and InPrivate Mode.]

2) Mute microphone or camera

In these 4 modes: Collaboration Mode, Speech Mode, Classic Mode, Spotlight Mode), you can select to mute the microphone or camera.

[Image: Screenshot of eMeetLink software showing the mute function for microphone and camera within the selected video modes.]

4. Anti-flicker

Most countries use 50HZ as the power grid operating frequency, and some countries such as the United States use 60HZ. Choose a suitable power frequency to avoid the screen flashing.

Anti-flicker

5. Zoom

In the classic mode, the camera can zoom in or out via eMeetLink. Then you can tune the view up, down, left, and right to adjust what is being framed.

[Image: Screenshot of eMeetLink software showing zoom controls with directional buttons and a slider for adjusting the zoom level, along with a reset button.]

[Image: Diagram illustrating the effect of zoom and pan controls on the camera's field of view.]

6. Panoramic frame

Each time you turn on the capsule, a panoramic view of the room will be captured by the camera and appear on the screen. You can check or uncheck this button to turn it on or off.

Panoramic frame

7. Sensitivity modulation

This button can adjust the capture speed of the device, which can be divided into three sensitivities: low, medium, and high. If you choose high, the device will capture the voice and video of the presenter more quickly.

Sensitivity modulation

8. Auto white balance

In the customize mode, you can click the “Auto” button to open or close the white balance auto adjustment function. When the auto button shows blue, the white balance of the image will be adjusted automatically. When the auto button shows grey, you can adjust the white balance according to your needs.

Auto White balance 50%

9. Image

You can drag the slider to adjust the image parameters like brightness, contrast, sharpness, and saturation according to your needs.

10. Image flip

The image of this device supports flip horizontal or vertical. Check the “Flip Horizontal” button to validate the horizontal flip of the image. Check the “Flip Vertical” button to validate the vertical flip of the image.

Image flip

Flip Horizontal

Flip Vertical

11. Angle initial position

This function allows you to adjust the panorama frame at the bottom of the screen. You can control the display center of the panorama frame through eMeetlink. Click Reset to return to the initial location of the G1 panorama.

Angle initial position

[Image: Diagram showing a circular control with degree markings for adjusting the initial camera angle.]

12. Restore default settings

After restoring default settings, all operating settings will be restored to the factory mode.

[Image: Screenshot of eMeetLink software showing a confirmation dialog box asking "Are you sure to restore the default Settings?" with options to Cancel and Confirm.]

1. Feedback

Write your feedback here to get EMEET customer service support.

2. FAQs

There are some common questions for your reference.

1. The device is plugged into the USB port of the computer, but the device is not detected. Please unplug the device USB and re-plug the computer USB port.
2. Computer (PC) software cannot be updated. Please check if the software has already been the latest version. You can also uninstall the software and download the latest eMeetLink software on the official EMEET website.
3. After renaming the device, the updated device name is not displayed. Click [Save] and [Confirm] the device name.
4. eMeetLink is unavailable. Please check if your device is connected to the computer via USB.

Still have questions?

3. User manual

Click the device to enter EMEET's official website and get the user manual.

[Image: Icons representing Microphone, Camera, Headphone, and Accessory.]

4. Compatible device

[Image: Grid displaying various EMEET camera, microphone, headphone, and accessory models including C950, C955, C960, C965, C970, C970L, C980 Pro, C990, Jupiter, Nova, M2, M220, M2 Max, Luna, Luna Lite, HS100, eMute, A300, A200.]

5. Contact info

Telephone

• +1 888 959 5320 Mon-Fri 9:00am - 5:00pm (EST)
• +81 8008051955月-金 10:00am - 6:00pm (JST)
• 400 8338 051 周一-周五9:00am - 5:00pm (BJT)

Official website

https://www.emeet.com

E-mail

• Support: support@emeet.com
• Marketing: marketing@emeet.com
• Sales: sales@emeet.com