Installation instructions for Carport

Important Read Before Assembly:

1. The ground for installing the carport must be flat and solid (suitable for expansion screws).
2. Always wear gloves ?, safety helmets ⛑️, and other protective gear to prevent injuries during installation.
3. The product is packaged in four separate boxes, which may arrive at different times. Please be patient and wait for all four boxes to arrive before starting the assembly.
4. Ensure you have a power drill ?, screwdriver ?, scissors ✂️, and a ladder ? ready for the installation.
5. At least two or more people are required for assembly.

CONTACT US:

If you have any questions about your purchase, please feel free to contact our after-sales email at info@garvee.com TEL:+1 (888) 857-8979

Assembly Instructions

Parts List:

• A: [Hexagonal Wrench] x4
• B: [Reinforcement Bar] x10
• C: [Top Reinforcement Bar] x5
• D: [Steel Post Connector] x5
• E: [Side Post Connector] x5
• F: [Side Post Connector] x5
• G: [Steel Post] x10
• H: [Steel Post] x10
• I: [Connecting Bar] x4
• J: [Connecting Bar] x2
• K: [Steel Post] x8
• L: [Metal Sheet Connector] x4
• M: [Fastener] x6
• N: [Longer Metal Sheet] x18
• P: [Metal Sheet] x18
• 1: [M6x60mm Screw] x20
• 2: [Washer] x20
• 3: [Expansion Screw] x12
• 4: [Self-tapping Screw] x306
• 5: [M5x25mm Screw] x12
• 6: [Gloves] x4
• 7: [Foam Tape] x1
• Sealing strip x2

Assembly Steps:

Step 1:

Use self-tapping screws (#4) to connect and secure the part (#D) to the steel post (#H).

Parts needed: D (1pc), H (2pcs), #4 (4pcs)

Diagram: Shows two steel posts (H) connected by a part (D) using screws (4).

Step 2:

Attach the top reinforcement bar (#C) to the assembled section of Step 1 using self-tapping screws (#4).

Parts needed: C (1pc), #4 (2pcs)

Diagram: Shows the top reinforcement bar (C) being attached to the structure from Step 1 using screws (4).

Step 3:

Use self-tapping screws (#4) to connect and secure the parts (#E and #F) to the steel post (#H), ensuring the side with the pre-punched holes is facing down.

Parts needed: E (1pc), F (1pc), #4 (4pcs)

Diagram: Shows parts E and F being attached to the steel posts (H) with screws (4). Close-ups indicate the side with holes should face down.

Step 4:

Connect and secure the steel post (#G) to the parts (#E and #F) using self-tapping screws (#4).

Parts needed: G (2pcs), #4 (4pcs)

Diagram: Shows steel posts (G) being attached to the structure from Step 3 using screws (4).

Step 5:

Secure the reinforcement bars (#B) between the steel posts (#G and #H) with self-tapping screws (#4).

Parts needed: B (2pcs), #4 (4pcs)

Diagram: Shows reinforcement bars (B) being attached between steel posts (G and H) using screws (4).

Repeat the above 5 steps to assemble five mainframes.

Diagram: Shows five assembled mainframes.

Step 6:

Arrange components #A, #J, #I, #I, and #A from left to right as shown, and secure them using self-tapping screws (#4).

Parts needed: A (4pcs), J (2pcs), I (4pcs), #4 (16pcs)

Diagram: Shows a row of components A, J, I, I, A being connected with screws (4).

Step 7:

Place the five mainframes above the base and secure them with self-tapping screws (#4). (At least two people should work together to complete this step.)

Parts needed: #4 (20pcs)

Diagram: Shows five mainframes being secured to a base with screws (4).

Step 8:

Attach the washer (#2) with the metal sheet (#L), then use M6 screws (#1) to connect and secure the steel post (#K) to the steel post (#G). Repeat this connection for the steel posts (#K) at all four corners. Then use M6 screws (#1) to attach the remaining steel posts (#K) to the steel posts (#G).

Parts needed: L (4pcs), #2 (20pcs), #1 (20pcs), K (8pcs)

Diagram: Shows steel posts (K) being attached to steel posts (G) using washers (2), metal sheets (L), and M6 screws (1). A close-up shows the connection detail.

Step 9:

Place the fasteners (#M) on the base (three on each side), and use a power drill to create twelve 10mm diameter holes in the ground. Then secure using expansion screws (#3).

Parts needed: M (6pcs), #3 (12pcs)

Diagram: Shows fasteners (M) being placed on the base and holes being drilled for expansion screws (3). A close-up shows the fastener and ground connection.

Step 10:

Install the longer metal sheet (#N) at both ends using pre-punched holes as reference points; ensure that the ends of the metal sheet extend 3.54 inches beyond the main frame.

Parts needed: N (1pcs), #4 (2pcs)

Diagram: Shows longer metal sheets (N) being attached to the ends of the carport frame with screws (4). Close-ups show the attachment point and the 3.54-inch extension.

Step 11:

Overlap every 2 metal sheets by about 1 inch for waterproof tape, and install the first row of metal sheets.

Parts needed: P (2pcs), N (1pcs), #4 (8pcs), #7 (1pcs)

Diagram: Shows metal sheets (N and P) being overlapped and attached with screws (4) and waterproof tape (7).

Step 12:

Pay attention to the overlapping method of different rows of metal sheets, and install the remaining metal sheets (#N and #P) in the same manner. Use self-tapping screws (#4) to fix all the metal sheets on the frames.

Parts needed: P (16pcs), N (16pcs), #4 (170pcs)

Diagram: Shows the remaining metal sheets (N and P) being installed, with close-ups illustrating the overlapping technique and screw attachment.