iScooter EB1 Electric Bike User Manual

Product Overview

The e-bike features the following components:

Handlebar Area:

• ? Brake Lever (x2)
• ?️ Display
• ? Front Reflector
• ? Bell

Frame and Components:

• ⚙️ Handlebar Height Adjustment Clamp
• ? Folding Mechanism
• ? Headlight
• ?️ Front Fender
• ? Front Disc Brake
• ? Saddle
• ? Rear Reflector
• ? Seatpost Clamp
• ? Charging Port
• ? Taillight & Brake Light
• 〰️ Rear Shock
• ?️ Rear Fender
• ? Rear Disc Brake
• ? Kickstand
• ? Pedal (x2)

Package Contents

Please check if all parts are present. If any parts are missing or damaged, please contact customer support.

• E-bike Frame x1
• Front Wheel x1
• Seat x1
• Front Fender x1
• Front Wheel Axle x1
• Left Pedal x1
• Right Pedal x1
• Charger x1
• User Manual x1
• Safety Instructions x1

Toolkit Contents:

• Double Open-Ended Wrench x4 (Sizes: 16 & 13, 16 & 13, 15 & 13, 10 & 8)
• Hex Wrench x5
• 2-in-1 Screwdriver x1 (Cross & Flat Heads)

Assembly

STEP 1: Install the Handlebar

1. Unfold the handlepost until you hear a click from the folding mechanism.
2. Open the lever of the handlebar height adjustment clamp, then insert the T handlebar into the handlepost.
3. Adjust the handlebar to your desired height, then fully close the lever of the handlebar clamp.
4. Adjust the handlebar and front fork so that they are both perpendicular (90°) to the bike frame.
5. Slide open the lever of the folding mechanism, fold down the handlepost, and tighten the retaining bolt.
6. Unfold the handlepost until you hear a click from the folding mechanism, then fully close the folding lever. Keep the handlepost and front fork still during the entire process.

WARNING: The handlebar clamp, handlepost folding lever, and handlepost retaining bolt must be secured tightly for your safety.

STEP 2: Install the Headlight & Front Fender

1. Remove the pre-installed bolt from the mounting hole of the headlight and front fender.
2. Pass the bolt through the holes of the headlight bracket, front fender bracket, and front fork in sequence.
3. Retighten the bolt or nut. Adjust the headlight and front fender to your desired angles before fully tightening the bolt or nut.
4. Remove the pre-installed fender stay bolts.
5. Attach the fender stay on the fork blades, then retighten the bolts.

STEP 3: Install the Front Wheel

1. Remove the front fork dropout protector after loosening its nuts. The dropout protector protects the fork from damage during transit, so keep it for future use.
2. Remove the nuts, washers, and bushings from the wheel axle, then pass the axle through the wheel hub. The narrow bushing should be located on the disc brake rotor side.
3. Sit the front fork dropouts onto the wheel axle, then reattach the washers as shown. Ensure the axle is seated properly in the dropouts and the safety washers catch the holes above the fork dropouts.
4. Re-tighten the acorn nuts securely. Ensure the brake rotor is centered between the brake pads.

STEP 4: Install the Seat

1. Open the lever of the quick-release seatpost clamp.
2. Insert the seatpost into the seat tube, adjust the seat to your desired angle and height, then close the lever.
3. Adjust the seat to your desired height and angle, then close the lever of the seatpost clamp.

WARNING:

• The part below the minimum insertion mark (including the mark) must be fully inserted into the seat tube.
• The seatpost must be tightened firmly by the clamp for your riding safety.

STEP 5: Install the Pedals

1. Rotate the axle of the left pedal counterclockwise onto the left crank arm, then tighten it.
2. Rotate the axle of the right pedal clockwise onto the right crank arm, then tighten it.

Display & Buttons

Display

The display shows various information:

• ? Signal Strength
• ? Headlight Status
• ? Battery Level
• ⚙️ Cruise Control Status
• ? Walk Assist Mode Status
• Current Speed (CUR)
• Maximum Speed (MAX)
• Average Speed (AVG)
• Odometer (ODO)
• Trip Distance (TRIP)
• Battery Voltage (VOL)
• Battery Current (CUR)
• Riding Mode (RM)
• Trip 1 (T1)
• Trip 2 (T2)

Buttons

• ➕ "+" Button:
  • Press to switch the speed level (lower to higher top speed).
  • Long press to turn on/off the headlight and taillight.
• Ⓜ️ Power Button:
  • Press to switch between ODO, TRIP, VOL, CUR and T1.
  • Long press for 2 seconds to turn on/off the e-bike.
• ➖ "-" Button:
  • Press to switch the speed level (higher to lower top speed).
  • Long press to activate walk assist mode (release to exit).

Speed Levels:

Settings

There are four setting items in the settings:

• P01: System of units (00000 means metric and 00001 means imperial)
• P02: Cruise control (00000 means off and 00001 means on)
• P03: Screen brightness (00001 means the darkest, 00002 means standard brightness, and 00003 means the brightest)
• P04: Odometer resetting (long press ➕ to reset the odometer when selecting P04)

1. Long press ➕ and ➖ simultaneously to enter the settings.
2. Press the M button to cycle through P01, P02, P03, and P04.
3. Press ➕ or ➖ to change its setting when selecting P01, P02, or P03.
4. Press the M button to switch to the next setting item (the parameter of the current setting item will be saved).
5. Long press ➕ and ➖ simultaneously to save all the changed parameters and return to the home screen.

When there is no operation for 8 seconds in the settings, the display will automatically return to the home screen and all the parameters (if changed) will be saved.

Specifications & Error Codes

Error Codes:

If you see any error code listed below on the screen, contact iScooter support.