Owner's Manual for ATOLL ELECTRONIQUE models including: PR200, PR200 Signature Preamplifier, Signature Preamplifier, Preamplifier
Index of /wp-content/uploads/2024/06
File Info : application/pdf, 4 Pages, 648.17KB
DocumentDocumentOWNER'S MANUAL ~ PREAMP CONNECTING 11 12 13 14 Optional Digital Board 1 23456 7 8 9 10 1) Aux input (or phono/SPDIF). 2) CD input. 3) Tuner input. 4) DVD input. 5) Tape input (IN-PLAY)(2). 6) Tape output (OUT-REC)(2). 7) BY-PASS input. 8) Preamp outputs (to 1 or 2 power amplifier or to a subwoofer). 9) Trigger output(1). 10) ON / SLEEP (preheating) power switch and general plug-in (with protection fuse). (1) Trigger output: this output is used to control the switching off/on of any device equipped with a compatible Trigger Jack Ø 3,5 mm input (see instructions for use). Trigger cable must be a stereo Male to Male jack plug Ø 3,5 mm (1/8"). Optional Digital Board 11) Bluetooth® receiver. 12) Coaxial inputs 1 & 2. 13) Optical inputs 1 & 2. 14) USB-B input. DETAIL OF FUNCTIONS 17 18 19 20 21 22 23 24 25 17) AUX input or Coaxial 1 18) CD input or Coaxial 2. 19) TU input or Optical 1. 20) DVD input or Optical 2. 21) TAPE input or USB. 22) BY-PASS input or Bluetooth®. 26 27 28 23) Digital/Analog indicator(3). 24) Headphones jack. 25) Volume control. 26) IR receiver. 27) Inputs selector(3). 28) ON / SLEEP key. Page 4 ATOLL ELECTRONIQUE PR200 Sig (2) TAPE input/output - Monitoring loop: The Tape function allows the recording of music from any source. Select your source then press the Tape button for about 3 seconds. The Tape led (21) lights up and indicates that the monitoring loop is active. This function can be used to insert a filter (equalizer type). (3) Selection of D/A sources (Digital/analogue): The source selection is made with the keys (27). To switch from analog sources to digital sources (if you have this option), you must press these 2 buttons simultaneously. When digital sources are selected, the indicator (23) lights up. REMOTE CONTROL An optional remote control is available. It is equipped with 2 Lithium CR2025 batteries. This remote control is also able to drive all others ATOLL's products: CD players, Tuner, DACs. Volume + Sources selection & + (except BY-PASS) Mute(4) BY-PASS selection (hold 3 sec) Direct access to sources(5) ON / SLEEP Management of led indicators Selection of digital inputs Nonfunctional keys (4) MUTE key: to get off the Mute, press any active key of the remote control. (5) Access to inputs OPT1 OPT2 COAX1 COAX2 USB BT is only possible if your appliance is equipped with the digital board. USING OF THE BY-PASS INPUT Careful: Reduce the volume of the source connected to BY-PASS before any use of the BY-PASS Input. The BY-PASS Input offers you the capacity to pass threw your preamplifier so the signal goes directly to the power amplifier with no attenuation. Use it to plug the output of an A/V processor. To avoid any trouble you can select this mode only via the front panel of preamplifier or with the BY-PASS key of the remote control (hold 3 seconds.). Once selected, mention "BY-PASS" appears on display. Then, no other functions are. Press once more BY-PASS to get back from BY-PASS mode. Page 5 ATOLL ELECTRONIQUE OWNER'S MANUAL ~ PREAMP USB INPUT (14) Your appliance is equipped with a High-Res. asynchronous USB Input (B type). It will be possible to use it only when you'll have downloaded the appropriate driver on your computer. This driver can be freely downloaded on our website at the page: https://www.atoll-electronique.com/en/xmos-specific-driver-usb/ You will find attached an explanatory note on its installation. This driver is not useful for MAC or Linux computers. In order to avoid problems with high quality format transfers (24 bits/192 kHz), it is recommended to use a USB connection cable with ferrite. ACCEPTED FORMATS · Accepted format on optical and coaxial inputs: 16-24 bits (44,1 kHz, 48 kHz, 88,2 kHz, 96 kHz, 176,4 kHz and 192 kHz). · Accepted format on USB Input: DSD: DSD64, DSD128 and DSD256. PCM: 16-32 bits (44,1 kHz, 48 kHz, 88,2 kHz, 96 kHz, 176,4 kHz, 192 kHz, 352,8 kHz, 384 kHz). BLUETOOTH® Your appliance allows the reception of audio signals sent since any device having a Bluetooth® transmitter (Smartphone, tab, computer...). First time association: · Select Bluetooth® input on the product (leds 22 & 23 switch ON). When led (22) BT is blinking, it means that no device is associated. · On your transmitter, select your PR in the list of available Bluetooth®. · Once connected, led (22) BT stays ON. The whole audio signals of your transmitter will then be transmitted towards your IN. Your emitter device will remain associated until you unlock the IN with your Smartphone or switch off your amplifier. Association of another emitter: If needed, dissociate the previous transmitter. (Blinking of led (22) BT means that the receiver is searching for new emitter) then associate it. For a better transmission between the devices, keep the transmitter closer than 5 meters from the receiver. Page 6 ATOLL ELECTRONIQUE PR200 Sig CAUTIONS · Do not make any connections when your device is turned on. · Install your appliance in a dry, well ventilated place away from any source of heat. · Make sure you never put anything on your preamplifier. · Avoid any short circuit. · Carefully observe the left and right connection directions. ADVISES · To optimize the performance of your device, you should switch it on at least half an hour before any listening, the time for the power stage to reach its ideal working temperature. · Your device will give you optimal listening quality after this time-lapse. · Between two uses, it is, therefore, preferable to let the device in the SLEEP position so that it remains at its optimum temperature. · At night or when you leave your home, it is best to use the main switch to turn off the device. · To optimize the sound quality of your system, we recommend that you choose good-quality connection cords. Do not hesitate to ask your specialist dealer for advice. TECHNICAL DATA Supply: 340 VA Total of capacitors: 31 867 µF Inputs: 5+1 BY-PASS Switch OFF consumption: 0 W SLEEP power consumption (preheating): 6 W ON consumption: Input Impedance: 7 W 220 k Sensitivity: 500 mV Signal/Noise ratio: 100 dBA Distortion at 1 kHz: 0,005% Bandwidth: 5 Hz - 200 kHz Rising time: 1,3 µs Dimensions: 440×300×95 mm Weight: 8 Kg (technical data are subject to changes) Page 3 ATOLL ELECTRONIQUE OWNER'S MANUAL ~ PREAMP You have just bought a preamplifier with exceptional audiophile performances. We really thank you for your confidence in our products. To get the best part of your appliance, please read carefully this manual. CONCERNING THIS OWNER'S MANUAL Paragraphs with grey and blue frames concern only appliance getting the optional digital board installed. YOU WILL FIND ENCLOSED A preamplifier. A remote control. One power lead. This manual with the certificate of guarantee. Latest update: 10th June 2024, 15:00 ATOLL ELECTRONIQUE® is a French Company that designs, manufactures, and commercializes all its products. Page 2 ATOLL ELECTRONIQUE PR200 Sig E.C. MARKING E.C. marking certified the conformity with low tension directive 73/23/CEE, directive CEM 89/336/CEE and national transpositions. WARRANTY CONDITIONS The guarantee is two years period from date of purchase. We recommend you to ask your dealer to fill the guarantee and to conserve it. The guarantee is only available for appliances which have been use correctly. CLEANING Before any cleaning, switch off your device. Use a soft and dry rag to clean up the appliance. Never use acetone, white-spirit, ammoniac, or any kind of product containing abrasive agent. Never try to clean up inside the appliance. Page 7 ATOLL ELECTRONIQUE OWNER'S MANUAL ~ PREAMP WARRANTY FORM ~ PR200 Sig To present to your dealer with the invoice when returning back the appliance: ATOLL ELECTRONIQUE® Bd des Merisiers 50370 BRECEY FRANCE Date of purchase: Place of purchase: Buyer signature: Dealer Stamp Page 8 ATOLL ELECTRONIQUE OWNER'S MANUAL PR200 SIGNATURE PREAMPLIFIER www.atoll-electronique.com