STANLEY TLM99 / TLM99s / TLM99si Laser Distance Measurer

User Safety

WARNING: Carefully read the Safety Instructions and Product Manual before using this product. The person responsible for the instrument must ensure that all users understand and adhere to these instructions.

WARNING: The following label information is placed on your laser tool to inform you of the laser class for your convenience and safety.

The TLM99 Products emit a visible laser beam as shown in Figure A. The laser beam emitted is Laser Class 2 per IEC 60825-1 and complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

Laser Safety Label Description: LASER 2, < 1mW @ 620-690 nm, IEC 60825-1:2014.

WARNING: While the laser tool is in operation, be careful not to expose your eyes to the emitting laser beam (red light source). Exposure to a laser beam for an extended time may be hazardous to your eyes. Do not look into the beam with optical aids.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada, Industry Canada (IC) Notices

Class B digital circuitry of this device complies with Canadian ICES-003. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, the radio transmitter(s) in this device may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

CAUTION

CAUTION: Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.

Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.

Battery Safety

WARNING: Batteries can explode or leak and can cause injury or fire. To reduce this risk:

• ALWAYS follow all instructions and warnings on the battery label and package.
• DO NOT short any battery terminals.
• DO NOT charge alkaline batteries.
• DO NOT mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.
• DO NOT mix battery chemistries.
• DO NOT dispose of batteries in fire.
• ALWAYS keep batteries out of reach of children.
• ALWAYS remove batteries if the device will not be used for several months.

NOTE: Ensure that the correct batteries as recommended are used.

NOTE: Ensure the batteries are inserted in the correct manner, with the correct polarity.

Recycling

DO NOT dispose of this product with household waste.

ALWAYS dispose of batteries per local code.

PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical and electronic waste under the WEEE Directive.

Declaration of Conformity

Stanley Tools declares that the CE Mark has been applied to this product in accordance with the CE Marking Directive 93/68/EEC.

This product conforms to IEC 60825-1:2014.

For further details please refer to:

• www.stanleytools.eu
• www.stanleytools.com

Product Overview

The STANLEY TLM99 series laser distance measurers are designed for accurate and efficient distance measurement. Key components and features are detailed below:

• Figure A - Laser Measurer Tool: Shows the main unit.
• Figure B - Battery Installation: Illustrates how to install batteries.
• Figure C - TLM99 keypad: Details the buttons for the TLM99 model.
• Figure D - TLM99 LCD Display: Shows the display for the TLM99 model.
• Figure E - TLM99s/TLM99si keypad: Details the buttons for the TLM99s and TLM99si models.
• Figure F - TLM99s/TLM99si LCD Display: Shows the display for the TLM99s and TLM99si models.

Laser Measuring Tool Description

The laser measuring tool consists of the following parts:

1. Laser Beam Window: Emits the laser beam.
2. LCD display: Shows measurement results and settings.
3. Keypad: For operating the device.
4. Warning & Safety Label: Contains important safety information and laser classification.
5. Battery Compartment: Houses the batteries.

Description of Figure A: The image shows the laser measuring tool with numbered callouts pointing to the Laser Beam Window (1), LCD display (2), Keypad (3), Warning & Safety Label (4), and Battery Compartment (5).

Battery Installation / Removal

Use Alkaline AA (LR6) Batteries.

Description of Figure B: The diagram shows the battery compartment and how to insert two AA batteries, noting the correct polarity (+ and -).

Product Overview TLM99

TLM99 Keypad (Figure C)

• UNITS: Press to change units (ft./in/m).
• CLEAR: Press to clear the last measurement or setting.
• +/-: Press x1 for ADD function; Press x2 for SUBTRACT function.
• ON: Press x1 to activate the laser; Press x1 to measure; 2 sec. press to change measurement reference from front to back of device.
• OFF: 2 sec. press for OFF.

TLM99 LCD Display (Figure D)

The LCD display shows measurement values, units (e.g., ft, m, in), battery status, and other relevant information.

Product Overview TLM99s & TLM99si

TLM99s & TLM99si Keypad (Figure E)

• UNITS: Press to change units (m/in/ft.).
• CLEAR: Press to clear the last measurement or setting.
• +/-: Press x1 for ADD function; Press x2 for SUBTRACT function.
• ON: Press x1 to activate the laser; Press x1 to measure; 2 sec. press for Continuous Measurement.
• OFF: 2 sec. press for OFF.
• Bluetooth: Press to activate/deactivate Bluetooth.

TLM99s / TLM99si LCD Display (Figure F)

The LCD display shows measurement values, units (e.g., ft, m, in), battery status, and other relevant information, similar to the TLM99.

Product Operation

Change Measurement Reference Point

By default, measurements are taken from the rear of the device. To change the reference point to the front of the device, press and hold the ON button for 2 seconds.

• Default measurement: from the rear of the device.
• To change reference: 2 sec. press to change measurement reference from back to front of device.
• Measurement from front: Measurement is from the front of the device.

Single Measurement

1. Press [ON button] to turn the device on.
2. Press [Laser button] to activate the laser.
3. Aim the laser at the target.
4. Press [Measure button] to take the measurement. The result is displayed.

Continuous Measurement

1. Press and hold the [ON button] for 2 seconds to start continuous measurement.
2. Aim the laser at the target.
3. The device continuously measures and updates the distance.
4. Press the [ON button] again to stop continuous measurement and capture the last value.

Functions

Addition (TLM99)

1. Press the '+' button once to activate the Add function.
2. Take the first measurement.
3. Take the second measurement to add to the first. The sum is displayed.

Addition (TLM99s/TLM99si)

1. Press the '+' button once to activate the Add function.
2. Take the first measurement.
3. Take the second measurement to add to the first. The sum is displayed.

Subtraction (TLM99)

1. Press the '-' button twice to activate the Subtract function.
2. Take the first measurement (this is the value from which the next measurement will be subtracted).
3. Take the second measurement to subtract from the first. The difference is displayed.

Subtraction (TLM99s/TLM99si)

1. Press the '-' button twice to activate the Subtract function.
2. Take the first measurement (this is the value from which the next measurement will be subtracted).
3. Take the second measurement to subtract from the first. The difference is displayed.

Area Measurement

Measure length and width to find AREA (Length x Width).

1. Press the UNITS button until 'Area' is selected.
2. Press the [Measure button] to measure the first distance (length).
3. Press the [Measure button] again to measure the second distance (width). The calculated area is displayed.

Volume Measurement

Measure length, width, and height to find VOLUME (Length x Width x Height).

1. Press the UNITS button until 'Volume' is selected.
2. Press the [Measure button] to measure the first distance (length).
3. Press the [Measure button] again to measure the second distance (width).
4. Press the [Measure button] a third time to measure the third distance (height). The calculated volume is displayed.

Units Conversion

Press the UNITS button to cycle through available measurement units (e.g., meters, feet, inches).

• TLM99: Press to change units (m/in/ft.).
• TLM99s/TLM99si: 2 sec. press to change units (m/in/ft.).

Bluetooth Operation: TLM99s and TLM99si

These models support Bluetooth connectivity for use with the STANLEY FloorPlan app.

1. Download App: Download the STANLEY® FloorPlan app to your smartphone or tablet from Google Play or the App Store.
2. Capture Room: Use the app to capture your room or space layout.
3. Pair Device: Pair your TLM99s/TLM99si device with the STANLEY® FloorPlan app via Bluetooth.
4. Verify Measurements: Verify the room/space measurements within the app.
5. Save/Share Floorplans: Save and share your floorplans in various formats (e.g., PDF, DXF, JPG).

Bluetooth Trademark Note: The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by STANLEY TOOLS is under license. Other trademarks and trade names are those of their respective owners.

Specifications

*Under favorable conditions (good target surface, room temperature) up to 10 m (33 ft.). Under unfavorable conditions such as bright sunlight, a very weakly reflecting target surface or large temperature fluctuations, the error can increase by ± 0.25 mm/m (± 0.003 in/ft.) for distances over 10 m (33 ft.).

Warranty

STANLEY warrants this product for a period of (2) years against deficiencies in material and workmanship. This LIMITED WARRANTY does not cover products that are improperly used, abused, altered or repaired. Please call 866-786-5924 for more information or return instructions. Unless otherwise noted, STANLEY will repair without cost, any STANLEY product found to be defective, including parts and labor charges, or at STANLEY's option, will replace such tools or refund the purchase price, less the amount for depreciation, in exchange for the defective tool.

THIS LIMITED WARRANTY EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply to you. This LIMITED LIFETIME WARRANTY gives you specific legal rights that may vary from state to state.

In addition to the warranty, STANLEY Lasers are covered by: 30-Day Money Back Guarantee. If you are not completely satisfied with the performance of your STANLEY Laser for any reason, you can return it within 30 days from the date of purchase with a receipt for a full refund.

IMPORTANT NOTE: The customer is responsible for the correct use and care of the instrument. Moreover, the customer is completely responsible for periodically checking the accuracy of the laser unit, and therefore for the calibration of the instrument. Calibration and care are not covered by warranty.

Description of '2YR LIMITED WARRANTY' badge: A badge indicating a 2-year limited warranty period.

Error Codes

Company Information

© 2014 Stanley Black and Decker, Inc, Egide Walschaertsstraat 14-16, 2800 Mechelen, Belgium. Visit: www.STANLEYTOOLS.eu

© 2014 Stanley Tools, 701 East Joppa Road, Baltimore, Maryland 21286. Visit: www.STANLEYLASERS.com