司顺工业设计
（晟珈壹）手动热压机(二开)SJY-H12151M和SJY-H15151M拆装款(钣金)-SKU7-8,SKU46-47-说明书-20241021 1733820796523 Technical Support and E-Warranty Certificate www.vevor.com/support
HEAT PRESS MACHINE
We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you
are actually saving half in comparison with the top major brands.
HEAT PRESS MACHINE
MODEL:SJY-H12151M/SJY-H15151M/SJY-H12151P/SJY-H15151P
NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us:
Technical Support and E-Warranty Certificate www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
-1-
Symbol
Symbol Description
Warning: To reduce the risk of injury, the user must read the instructions manual carefully.
This symbol, placed before a safety comment, indicates a kind of precaution, warning, or danger. Ignoring this warning may lead to an accident. To reduce the risk of injury, fire, or electrocution, please always follow the recommendations shown below. CORRECT DISPOSAL: This product is subject to the provision of European Directive 2012/ 19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.
WARNING
1.Warnings must be followed carefully to avoid body injury, improper use may result in electric shock, fire, personal injury and other damage. 1)Keep unplug when moving the machine. 2)Keep unplug when installing accessories. 3)Place on a f at and stable platform and operate under ventilated conditions. 4)Wear special protective equipment when operating the machine. 5)Do not use this machine in a hazardous-location. 6)Do not use when the machine is not working properly. 7)Do not disassemble and repair this machine. 8)Do not use an unsuitable AC Outlet. 9)Do not touch the heating plate when the machine is heating 10)Do not use in humid environment or contact with water Do not infiltrate liquid in the machine to prevent fire or electric shock caused by short circuit. 11)Do not use the power supply that does not meet the rated voltage. The power
-2-
supply that does not meet the specified voltage may cause fire or electric shock. 12)Ensure that the machine is grounded so as not to cause harm to body. 13)Do not touch the rotating rod or bearing part with y ur fingers during use in case of injuries. 14)If the machine is not in use for a long time, please unplug the power cord from the socket. 15) Do not use the machine during thunderstorms or lighting to avoid damage to the machine. 16)Place the machine smoothly on the flame-retardant table and keep away from flammable and explosive items. 17)Please stop using it if the machine smokes, emits a peculiar smell , or becomes noisy and in other abnormal conditions. 18)This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision 19)Type X attachment: If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. 20)In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
Please turn off the power when plug or unplug the connector
-3-
FCC INFORMATION
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This product may cause harmful interference. 2)This product must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the product. Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception,which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures. · Reorient or relocate the receiving antenna. · Increase the distance between the product and receiver. · Connect the product to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for assistance.
-4-
Contents 1. SPECIFICATION.................................................................. 6 2. PRODUCT DIAGRAM............................................................7 3. CONTROL PANEL................................................................8 4. PARTS LIST........................................................................9 5. ASSEMBLY METHOD...........................................................10 6. OPERATION........................................................................13 7. TEMPERATURE CONTROLLER OPERATION METHOD..............14 8. PRINTING METHODS............................................................17 9. REPLACE BAKING CAP MAT..................................................19 10. RECOMMENDED PARAMETER..............................................21 11. TROUBLE SHOOTING FOR TRANSFER QUALITY.....................22
-5-
1. SPECIFICATION
Model Heat Size
SJY-H12151M
12x15inch (30×38cm)
SJY-H12151P
12x15inch (30×38cm)
Product
Temperat ure
Range
Time Range
32-480°F(0-250) 0-999 Seconds
32-480°F(0-250) 0-999 Seconds
Voltage
120V~ 60Hz
220-240V~ 50Hz
120V~ 60Hz
220-240V~ 50Hz
Power
1150W
1050W
950W
900W
-6-
2. SPECIFICATION
Model Heat Size
SJY-H15151M
15x15inch (38×38cm)
SJY-H15151P
15x15inch (38×38cm)
Product
Temperat ure
Range
Time Range
32-480°F(0-250) 0-999 Seconds
32-480°F(0-250) 0-999 Seconds
Voltage
120V~ 60Hz
220-240V~ 50Hz
120V~ 60Hz
220-240V~ 50Hz
Power
1400W
1350W
1400W
1350W
-7-
3. PRODUCT DIAGRAM -8-
4. CONTROL PANEL
Display Areas
Indicator Lights
Function Buttons
Upper
Lower OUT WORK °F °C SET
Displays temperature values or parameter names. Displays timer values or parameter settings. Indicates heating is operating. Indicates countdown is operating. Indicates temperature values in Fahrenheit. Indicates temperature values in Celsius. Enters/Exits primary parameter menus or confirms settings when pressed. Enters/Exits secondary parameter menus or confirms settings when held. Increases values or converts settings in parameter menus. Starts/Stops/Resets countdown Decreases values or converts settings in parameter menus
-9-
5. PARTS LIST
Heating Plate
Heat Press Machine Frame
Lift Handle with Pressure Plate
Flat Base
Silicone Mat
Foam Mat
Curved Base
- 10 -
Cap Press Plate
A
Crossed Screw M5*20 x 2 C
M5*10 x 4 E
Washer x 4
B Nut x 2
D M8*16 x 4
Lower Slide x 2
Slider Handle
- 11 -
6. ASSEMBLY METHOD - 12 -
- 13 -
7. OPERATION - 14 -
8. TEMPERATURE CONTROLLER OPERATION METHOD 1.Turn on the power switch, it shows present temperature, and are increasing. 2.Parameter setting guide: Temperature setting: Press "SET"one time, the digital display on the upper screen will show "SP", the bottom screen will show your last set temperature value, press""to increase the temperature value, press""to decrease the temperature value. For example, you can set the temperature value into 300 Fahrenheit, that value is to check whether your control box is in good condition. Kindly note: Long press"" and " ", the temperature value will change fast.
Working Time setting: Press "SET" once again, the digital display on the upper screen will show "ST", the bottom screen will show your last press time value, press ""to increase the press time value, press ""to decrease the press time value.
Degrees Celsius and Fahrenheit transfer Press the "SET"button for 3th time, the digital display on the upper screen will
- 15 -
show "C-F", Situation1:If the bottom screen shows "C", the current temperature unit is Celsius, please press""or "" to transfer the unit into "F"(F is Fahrenheit).Press "SET" one more time to save your setting. Situation 2:If the bottom screen shows "F", press "SET" to save your setting. Countdown time setting 1.When pressing the heating plate down, begin printing, then press"" the set working time will automatically countdown. 2.When the timing is over, the buzzer will beep. Lift up the handle and then retrieve the object and finish DIY gift printing.(lf the handle is difficult to lift up, you can anticlockwise the pressure regulator to decrease the pressure.) 3.Once the heat press finished one printing countdown, the counter will count one time. It is normal for the silicone pad to generate a small amount of smoke when the product is used, and it will disappear on its own after being heated for a few times.
Suggestion Before Use The Pressure Adjustment Knob controls the amount of force that will be used to push the transferred image into the fibers of the garment. Clockwise increases pressure. Counterclockwise decreases it. · The Control Panel on the right upper face of the casing is where you will set heat and times requirements of your project. These will vary depending on the vinyl or transfer paper used. · The handle opens & closes the top & bottom Heated Platens of the revolve press. ·
How to calibrate your heat press machine 1. Turn the pressure knob counterclockwise a few times to lower the pressure on the platens. 2.Place a piece of paper onto the bottom of the platen. 3.Close the revolve press using the handle. 4.Pull on the paper.
- 16 -
5.If the paper moves at all, turn the knob clockwise and try again. 6.Try again and repeat until the paper doesn't move at all. This is your "Medium" pressure. From the "Medium" setting, high pressure will be clockwise one to two turns. Low pressure will be counterclockwise one to two turns. (The number of turns will depend on the thickness of the garment.
9. PRINTING METHODS 1.Adjust pressure to your requirement(Please refer to "how to calibrate your heat press machine" suggestion). Plug in the power cord and turn the power switch ON. 2.The temperature will auto starts to rise. In this time you can set the transfer temperature and press time. 3.Once the temperature rises to the set temperature, the buzzer will Send out the "BEEF" sound. 4. Place the object (i.e.T-shirt) on the press bed. Pull down the handle to press the object. Then press the "" button to start countdown time. 5.Wait for the time to end up with a long buzzer sound.(Note:There will be about 5s time for the long buzzer to notify you it has finished; after that, 5s for the short buzzer will appear to notify you whether you still go on to the next work.) 6.Work finish and take out the object. 7.Turn off the power switch.
- 17 -
Turn off the power and pull out the mat. It is recommended to wear heat-resistant gloves when removing clothes or remove them after 2-3 minutes. Be careful of hot heat. Precautions: The area 5cm from the edge of the heating plate is anon-hot stamping area. If use heating transfer paper, bast cover a protective cover sheet on top to avoid pattern residue. Tips: .1. If it's for a T-shirt, please flat it by preheating it for 3-5 seconds to remove wrinkles and moisture, ironing clothes likewise. 2. It's better if you put a white cloth on the transfer paper to avoid unnecessary marks when setting the temperature too high.
- 18 -
10. REPLACE BAKING CAP MAT - 19 -
- 20 -
11. RECOMMENDED PARAMETER - 21 -
12. TROUBLE SHOOTING FOR TRANSFER QUALITY Pale color: The temperature is too low/the pressure is not correct/or not pressed long enough. Blurring Patter: Too much transfer time causes proliferation. Part Blurring of Pattern: Heat was incorrectly distributed through the heat plate. Allow more time between press operations. Pressure distribution can also be the cause, which can be set on the four plate surface adjusters. Please note that it has been factory set, and there should be no need to adjust them. Dull Surface of Pattern: The pressure is too large, or the temperature is too high. Scarred Pattern transfer time is too long. Different Pattern Color: The pressure is incorrect, or the transfer paper is poor quality. Adhesive Paper: the temperature is too high or poor printing ink. Ps. Partten material always uses heat transfer paper and DTF film Please check the DTF film suggested removing time to avoid that the remove time is incorrect cause failure.
- 22 -
Tutorial Video
Temperature controller operation method Temperature sensor replace tutorial
- 23 -
Manufacturer:Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
EC
REP E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.
UK
REP
YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
- 24 -
Technical Support and E-Warranty Certificate www.vevor.com/support
WPS 文字