EVERCROSS EK6 User Manual

PRODUCT OVERVIEW

The EVERCROSS EK6 electric bike features the following components:

• 1 LCD Display
• 2 Handlebar grip
• 3 Brake Lever
• 4 Headlight
• 5 Tire
• 6 Disc brake pad
• 7 Front Fork
• 8 Disc Brake
• 9 Folder
• 10 Pedal
• 11 Chainring
• 12 Battery
• 13 Chain
• 14 Transmission
• 15 Motor
• 16 Rear Rack
• 17 Tail Light
• 18 Seat Tube Clip
• 19 Seat Tube
• 20 Saddle

A visual representation of the bike with numbered components is provided.

ASSEMBLY

Before beginning assembly, inspect the packaging for all necessary components and accessories. Contact EVERCROSS customer service if any items are missing or damaged.

PARTS DESCRIPTION

The following parts are included for assembly:

• 1. Seat & post
• 2. Pedal
• 3. Wrench 15 mm
• 4. 16-in-1 Tool
• 5. Wheel Reflectors
• 6. Front wheel quick release
• 7. Front Mudguard
• 8. Front Wheel Assembly

A visual guide showing these parts is available.

ASSEMBLY - VEHICLE UNFOLD

1. Open the telescopic adjustment buckle of the foldable standpipe and insert the telescopic standpipe in the direction indicated by the arrow.
2. Insert the telescopic standpipe, adjust to the desired height, and press the adjustment buckle as shown. Note: Adjust the screw at '1' if the buckle is too tight or loose.
3. Stand up the foldable standpipe and close it.
4. Confirm the quick release plug is inserted, then lift the pull rod and wrench as shown.
5. Press down the folding wrench to lock the foldable standpipe. Note: Adjust the screw at '1' if the folding wrench is too tight or loose.

ASSEMBLY - FRONT FENDER

1. Pre-install the headlight and fender on the front fork using the headlight fixing screw.
2. Attach the nut.
3. Tighten the screws using the 16-in-1 Tool (allen wrench and socket).
4. Remove the pre-installed fender stick fixing screws from the front fork using the 16-in-1 Tool (Allen wrench).
5. Fix the front mudguard sticks into the corresponding screw holes on the front forks and tighten the screws with the 16-in-1 Tool (Allen wrench).

ASSEMBLY - FRONT WHEEL

1. Loosen the nut using the 16-in-1 Tool (open-end wrench) and remove the fork leg protection shaft.
2. Unscrew the nut of the quick release lever, and remove the gasket, sleeve, and nut from one side.
3. Insert the quick release lever.
4. Insert the sleeve.
5. Note: Ensure the disc brake pads are correctly placed within the disc brake.
6. Insert the front wheel into the front fork dropout and lock the screws. Ensure the front wheel is centered in the front fork tube; adjust if necessary.
7. Insert two gaskets and nuts in sequence.
8. Use the No. 15 wrench to tighten the nuts on both sides simultaneously. Note: Adjust the gasket position until it snaps into the groove as shown in the figure.

ASSEMBLY - SEAT

1. Pull the quick release lever of the seat post clamp as shown.
2. Insert the seat post and adjust it to the desired height. Ensure the insertion depth exceeds the safety mark.
3. Press the quick release lever as shown. Note: Adjust the screw at '1' if the folding quick release lever is too tight or too loose.

ASSEMBLY - WHEEL REFLECTORS

Place the wheel reflector on the designated fixed position of the wheel hub. Secure it by tightening screws '1' and '2' with a Phillips screwdriver. This process is the same for both front and rear wheel reflectors.

ASSEMBLY - REAR FENDER STICK

1. Using the No. 4 Allen wrench from the 16-in-1 tool, remove the fixing screws and washers for the fender sticks pre-installed on the left and right sides of the frame.
2. Insert the stick, then tighten the fixing screws and washers on both sides.

ASSEMBLY - PEDAL

• Left pedal installation: The pedal axis is marked with 'L'. Screw the pedal axis counterclockwise into the crank arm on the left side by hand, then tighten it counterclockwise with the 16-in-1 Tool (open-end wrench).
• Right pedal installation: The pedal axis is marked with 'R'. Screw the pedal axis clockwise into the crank arm on the right side by hand, then tighten it clockwise with the 16-in-1 Tool (open-end wrench).

REMOVE & INSTALL THE BATTERY

ASSEMBLY - BATTERY REMOVAL & INSTALLATION

Battery Removal:

1. Locate and pull up the seat handle.
2. Flip the seat upwards.
3. Turn the key to the "PUSH" position to release the battery.
4. Lift the battery handle to remove the battery.

Battery Installation:

1. Locate and pull up the seat handle, then flip the seat upwards.
2. Align the notch at the bottom of the battery with the slide mechanism.
3. Insert the battery downwards.
4. Press down to secure the seat in its original position.

CONTENU DU COLIS (Package Contents)

Carefully check the contents of the package. If any items are missing or damaged, please contact EVERCROSS customer service for assistance.

Note: Retain the original packaging in case the bicycle needs to be returned in the future.

The package includes:

• 1 x Electric Bicycle
• 1 x Bicycle Lock
• 1 x Pump
• 1 x Charger
• 1 x 16-in-1 Tool
• 1 x 15 mm Wrench
• 1 x User Manual