details.In
Clooud | Rovereto | Omedra
User Manual for RCA models including: Window Wall Type Room Air Conditioner, Multi-Step Speed Electronic Control
this manual carefully and keep it for future reference. WINDOW/WALL TYPE ... as it may c ause fi re an d el ectric sh ock, it may cause an injury.
File Info : application/pdf, 15 Pages, 2.29MB
DocumentDocumentWINDOW/WALL - TYPE ROOM AIR CONDITIONER MULTI-STEP SPEED ELECTRONIC CONTROL TABLE OF CONTENTS Important Safety Instructions ..........................1-3 Installation Instructions ....................................4-8 Normal Sounds .................................................9 Air Conditioner Features.............................. 9-11 Care and Cleaning ......................................11-12 Troubleshooting Tip .....................................12-13 Before using your air conditioner, please read this manual carefully and keep it for future reference. IMPORTANT SAFETY INSTRUCTIONS READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury. CAUTION This symbol indicates the possibility of injury or damage to property. Never do this. Always do this. WARNING ! Plug in power plug properly. Otherwise, it may cause electric shock or fire due to excess heat generation. ! Always install circuit breaker and a dedicated power circuit. Incorrect installation may cause fire and electric shock. ! Always ensure effective grounding. Do not operate or stop the unit by inserting or pulling out the power plug. It may cause electric shock or fire due to heat generation. Do not operate with wet hands or in damp environment. It may cause electric shock. Do not damage or use an unspecified power cord. It may cause electric shock or fire. If the power cord is damaged, it must be replaced by the manufacturer or an authorised service centre or a similarly qualified per son in order to avoid a hazard. Do not direct airflow at room occupants only. This could damage your health. Do not allow water to run into electric parts. ! Do not modify power cord length or share the outlet with other appliances. Incorrect grounding may cause electric shock. It may cause failure of machine or electric shock. It may cause electric shock or fire due to heat generation. ! Unplug the unit if strange sounds, smell, or smoke comes from it. It may cause fire and electric shock. ! Keep firearms away. Do not use the socket if it is loose or damaged. It may cause fire and electric shock. Do not use the power cord close to heating appliances. It may cause fire. It may cause fire and electric shock. ! Ventilate room before operating air conditioner if there is a gas leakage from another appliance. Do not open the unit during operation. It may cause electric shock. Do not use the power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc. It may cause an explosion or fire. Do not disassemble or modify unit. It may cause explosion, fire and, burns. It may cause failure and electric shock. 1 IMPORTANT SAFETY INSTRUCTIONS ! ! CAUTION When the air filter is to be removed, do not touch the metal parts of the unit. It may cause an injury. Do not put a pet or house plant where it will be exposed to direct air flow. This could injure the pet or plant. ! Ventilate the room well when used together with a stove, etc. An oxygen shortage may occur. Do not use strong detergent such as wax or thinner but use a soft cloth. Appearance may be deteriorated due to change of product color or scratching of its surface. Do not clean the air conditioner with water. Water may enter the unit and degrade the insulation. It may cause an electric shock. Do not use for special purposes. Do not use this air conditioner to preserve precision devices, food, pets, plants, and art objects.It may cause deterioration of quality, etc. Stop operation and close the window in storm or hurricane. Operation with windows opened may cause wetting of indoor and soaking of household furniture. ! When the unit is to be cleaned, switch off, and turn off the circuit breaker. Do not clean unit when power is on asit may cause fire and electric shock, it may cause an injury. !! Ensure that the installation bracket of the outdoor appliance is not damaged due to prolonged exposure. If bracket is damaged, there is concern of damage due to falling of unit. Always insert the filters securely. Clean filter once every two weeks. Operation without filters maycause failure. ! Hold the plug by the head of the power plug when taking it out. It may cause electric shock and damage. ! Turn off the main power switch when not using the unit for a long time. It may cause failure of product or fire. Do not place obstacles around air-inlets or inside of air-outlet. Do not place heavy object on the power cord and ensure that the cord is not compressed. Do not drink water drained from air conditioner. It may cause failure of appliance or accident. There is danger of fire or electric shock. It contains contaminants and could make you sick. Use caution when unpacking and installing. Sharp edges could cause injury. ! If water enters the unit, turn the unit off at the power outlet and switch off the circuit breaker. Isolate supply by taking the power-plug out and contact a qualified service technician. CAUTION This appliance is not intended for use by persons (including children) with reduced physical ,sensory or mental capabilities or lack of experience and knowledge,unless they haveb eengivensu pervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air conditioner in a wet room such as a bathroom or laundry room. The appliance with electric heater shall have at least 1 meter space to the combustible materials. Contact the authorised service technician for repair or maintenance of this unit. Contact the authorised installer for installation of this unit. ! 2 IMPORTANT SAFETY INSTRUCTIONS NOTE: WARNING The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire. Please refer to the section Operation of Current Device for details.In the event that the power supply cord is damaged, it cannot be repaired-it must be replaced with ac ordf romt heP roductM anufacturer. WARNING Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord. Grounding type wall receptacle For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WARNING Prevent Accidents To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following: Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the the cabinet and behind the grille. If the air conditioneri s to be installed in a window, you will probably want to clean both sides of the glass first.I f the windowis a triple-track type with a screen panel included, remove the screen completely before installation. Be sure the air conditionerhas been securely and correctly installed according to the installation instructions in this manual. Save this manual for possible future use in removing or installing this unit. When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power supply cord with 3-prong grounding plug and current detection device WARNING Electrical Information The complete electical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements. Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Ensure the receptacle is accessible after the unit installation. Do not run air conditioner without side protective cover in place.This could result in mechanical damage within the air conditioner. Do not use an extension cord or an adapter plug. Operation of Current Device (Applicable to the unit adopts current detection device only ) The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner. 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button, you will notice a click as the RESET button pops out. 3. Press the RESET button, again you will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this it also indicated by a light on the plug head.) NOTE: Do not use this device to turn the unit on or off. Always make sure the RESET button is pushed in for correct operation. The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from the product manufacturer. NOTE:This air conditioner is designed to be operated under condition as follows: Cooling Outdoor temp: operation Indoor temp: 64-109OF/18-43OC (64-125OF/18-52OC for special tropical models) 62-90OF/17-32OC Heating Outdoor temp: operation Indoor temp: 23-76OF/-5-24OC 32-80OF/0-27OC Note: Performance may be reduced outside of these operating temperatures. 3 INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector s use. IMPORTANT- Observe all governing codes and ordianaces. Note to Installer- Be sure to leave these instructions with the Consumer. Note to Consumer- Keep these instructions for futrue reference. Skill level- Installatio of this appliance requires basic mechanical skills. Completion time- Approximately 1 hour. We recommend that two people install this product. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Warranty. You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner. WINDOW REQUIREMENTS Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches(584mm to 914mm) . CAUTION Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Do not change the plug on the power cord of the air conditioner. Aluminum house wiring may present special problems- consult a qualified electircian. When handling unit, be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils. TOOLS YOU WILL NEED Screwdriver Level TOOLS YOU MAY USE Screwdriver Pencil Ruler or tape measure H Scissors or knife Model 5000~8000Btu/h H 14 (356mm) Table 1 10000~12000Btu/h 15-1/2 (394mm) NOTE: Save Carton and these Installation Instructions for future reference. The carton is the best way to store unit during winter, or when not in use. 4 INSTALLATION INSTRUCTIONS 1 PREPARE THE WINDOW Lower sash must open sufficiently to allow a clear vertical opening (H) of following size (see Table 1). Side louvers and the rear of the AC must have clear air space to allow enough airflow through the condenser,for heat removal. The rear of the unit must be outdoors, not inside a building or garage. Mounting Hardware C: Align the hole in the top rail with those in the top of the unit as shown in Fig.B Fig.B 3/4 (or 1/2 ) Screws (7) Lock Frame Sash Lock Window sash Weather (2) (1) seal foam stripping (1) (10 *3/4 *1/12 ) (5) NOET: Weather stripping is only for Energy star models. D: Secure the top rail to the unit with the 3/8 Screws as shown in Fig.C. Fig.C 2 PREPARE AIR CONDITIONER A: Remove the air conditioner from the carton and place on a flat surface. B: Remove top rail and R1 hardware (R1 hardware only for Energy star models) from the packaging material as shown in Fig. A. Top Rail Hardware 3/8 Screws (4) Top Rail (1) R1 hardware (2) Fig.A Packaging R1 hardware (for <10000 Btu/h models only ) Top Rail R1 hardware(for >10000Btu/h models only ) NOTE: For safety reasons, all four(4) screws MUST be securely fastened. NOTE: The top rail hardware and the Fig.A, Fig.B and Fig.C are not applicable to the units more than 10000Btu/h.Before installing unit, the top rail must be assembled on the unit (For <10000Btu/h models only). 3 INSTALL THE ACCORDION PANELS NOTE: Top rail and Sliding Panels at each side are offset to provide the proper pitch to the rear of (5/16 ). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained. A.Place unit on floor, a bench or a table. Hold the Accordion Panel in one hand and gently pull back the center to free the open end. See Fig.1 Fig.1 5 INSTALLATION INSTRUCTIONS B. Slide the free end " " section of the panel directly into the cabinet as shown in Fig. 2. Slide the panel down. Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet. " "section Fig.2 C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. Fig.3. Top Rail 4 SECURE THE ACCORDION PANELS A.Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (Fig.5). Carefully close the window behind the top rail of the unit. Measure from the cabinet edge H H:About 3/4 to 1 for 5 to 8K); H:About 1 to 13/8 for 10 to12K); INSIDE OUTSIDE Wooden Windows Fig.5 NOTE: Check that air conditioner is tilted back about H (Fig.5)(tilted about 3Oto 4Odownward to the outside). After proper installation, condensate should not drain from theoverflow drain hole duringnormalu se,correct the slope otherwise. B.Extend the side panels out against the window frame (Fig.6). Bottom Rail Fig.3 D. Slide the panel all the way in and repeat on the other side. Fig.4 Top left Top Rail Top right window frame Fig.6 5 INSTALL SUPPORT BRACKET A.Place the frame lock between the frame extensions and the window sill as shown(Fig.7). Drive 3 / 4" (19mm)or 1 / 2 "(12.7mm) locking screws through the frame lock and into the sill . NOTE: To prevent window sill from splitting,drill 1 / 8" (3mm) pilot holes before driving screws. Bottom Rail NOTE: If storm window blocks AC, see Fig. 11. 6 Fig.7 INSTALLATION INSTRUCTIONS B.Drive 3/4" (19mm) or 1/2" (12.7mm) locking screws through frame holes into window sash (Fig.8). Fig.8 C.To secure lower sash in place, attach right angle sash lock with 3/4" (19mm) or 1/2" (12.7mm) screw as shown(Fig.9). 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Measure the inner width of the side curtain Fig.11 Fig.9 D.Cut Window sash seal foam and insert it in the space between the upper and lower sashes (Fig.10). FOAM SEAL Fig.10 6 INSTALL R1 HARDWARE (only be applicable to Energy star models ) In order to minimize air leaks and ensure optimal insulation, it is necessary to install the included R1 hardware to the side curtain. Follow the instructions below. Step 1. After the unit is installed to the window, measure the inner width of the side curtain as shown (Fig.11). Step 2. Remark a line on the provide R1 insulation panel according to a length 1/8 (3mm) less than the measured width in step 1, then cut the R1 insulation panel along the line (Fig.12). or Fig.12 Step 3. Slide the R1 insulation panel into the side curtain, the side with pattern should facing the indoor side.(Fig.13). Fig.13 Step 4. Repeat on the other side. 7 INSTALLATION INSTRUCTIONS 7 INSTALL WEATHER STRIPPING (only be applicable to Energy star models ) In order to minimize air leaks between the room air conditoner and the window opening, trim the weather sttipping with a proper length, peel off the protective backing and plug any gaps if needed (Fig.14). If AC is Blocked by Storm Window Add wood as shown in Fig.15, or remove storm window before air conditioner is installed. If Storm Window Frame must remain, be sure the drain holes or slots are not caulked or painted shut. Accumulated Rain Water or Condensation must be allowed to drain out. Removing AC From Window Turn AC off, and disconnect power cord. Remove sash seal from between windows, and unscrew safety sash lock. Remove screws installed through frame and framelock. Remove the R1 Panel and close (slide) side panels into frame. Keeping a firm grip on air conditioner, raise sash and carefully remove. Be carefully not to spill any remaining water while lifting unit from window. Store parts WITH air conditioner. Fig.14 SASH Storm window frame or other obstruction. 1-1/2"min (38 mm) Board thickness as required, for proper pitch to rear, along entire sill. Fasten with nails or screws. Fig.15 8 NORMAL SOUNDS Sound of Rushing Air At the front of the unit, you may hear the sound of rushing air being moved by the fan Gurgle/Hiss Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation. High Pitched Chatter High efficiency compressors may have a high pitched chatter during the cooling cycle. Vibration Unit may vibrate and make noise because of poor wall or window construction or incorrect installation. Pinging or Switching Droplets of water hitting condenser during normal operation may cause pinging or switching sounds. NOTE: All the illustrations in this manual are for explanation purpose only. Your air conditioner may be slightly different. The actual shape shall prevail. AIR CONDITIONER FEATURES ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote. ADJUSTS TEMPERATURE OR TIME ACTIVATES TIMER CHECK FILTER RESET BUTTON SETS MODE REMOTE SIGNAL RECEPTOR ENERGY SAVER MODE Temp Temp Timer Timer On Off Check Filter Timer Sleep Auto Cool Dry Fan Clean Air Auto Low Med High Mode Fan Energy Saver Follow Me On/Off UNIT CONTROL ADJUSTS TEMPERATURE OR TIME DISPLAYS TEMPERATURE OR TIME OR ERRORCODES SLEEP MODE CLEAN AIR MODE (on some models) SET FAN SPEED FOLLOW ME INDICATOR (on some models) TURNS UNIT ON OR OFF TO TURN UNIT ON OR OFF: Press ON/OFF button toturn unito n or off. NOTE:The uni t wi ll ini tia te automatically the Energy Saver function under Cool, Dry,Auto(only Auto-Cooling and Auto-Fan) modes. TO CHANGE TEMPERATURE SETTING: Press / UP/DOWN button to change temperature setting. NOTE:Press or hold either UP( ) or DOWN ( ) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 62OF(17OC) and 86OF(30OC). If you want the display to read the actual room temperature, see To Operate on Fan Only section. CLEAN AIR FEATURE: (on some models) Press Clean Air button,the ion generator is energized and will help to removepollen andimpurities from the air, and trap them in the filter. 9 AIR CONDITIONER FEATURES TO ADJUST FAN SPEEDS: Press to select the Fan Speed in four steps-Auto, Low, Med or High. Each time the button is pressed, the fan speed mode is shifted. On Dry mode,the fan speed is controlled at Low automatically. SLEEP FEATURE: Press Sleep button to initiate the sleep mode. In this mode the selected temperature will increase by 2OF/1(or 2)OC 30 minutes after the mode is selected. The temperature will then increase by another 2OF/ 1(or 2)OC after an additional 30minutes. This new temperature will be maintained for 6 hours before it returns to the originally selected temperature. This ends the Sleep mode and the unit will continue to operate as originally programmed. The Sleep mode program can be cancelled at any time during operation by pressing the Sleep button again. CHECK FILTER FEATURE: Press Check filter button to initiate theis feature. This feature is a reminder to clean the Air Filter for more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the Check Filter button and the light will go off. ENERGY SAVER FEATURE: Press Energy saver button to initiate this function. This function is available on COOL, DRY, AUTO (only AUTO-COOLING and AUTO-FAN) modes.The fan will continue to run for 3 minutes after the compressor shuts off.The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on and Cooling Starts. FOLLOW ME FEATURE:(on some models) Light flashing Follow Me Energy Saver On/Off This feature can be activated from the remote control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature control at its location. To activate the Follow Me feature, point the remote control towards the unit and press the Follow Me button. The remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again.If the unit does not receive the Follow Me signal during any 7 minutes interval, the unit will beep to indicate the Follow Me mode has ended. TO SELECT THE OPERATING MODE: To choose operating mode, press Mode button.Each time you press the button, a mode is selected in a sequence that goes from Auto, Cool, Dry and Fan. The indicator light beside will be illuminated and remained on once the mode is selected. The unit will initiate automatically the Energy Saver function under Cool, Dry, Auto(only Auto-Cooling and Auto-Fan) modes. To operate on Auto feature: When you set the air conditioner in AUTO mode, it will automatically select cooling, heating(cooling only models without), or fan only operation depending on what temperature you have selected and the room temperature. The air conditioner will control room temperature automatically round the temperature point set by you. In this mode, the fan speed cannot be adjusted, it starts automatically at a speed according to the room temperature. To operate on Fan Only: Use this function only when cooling is not desired,such as for room air circulation or to exhaust stale air(on some models). (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. In Fan only mode ,the temperature is not adjusted. To operate on Dry mode: In this mode, the air conditioner will generally operate in the form of a dehumidifier. Since the conditioned space is a closed or sealed area, some degree of cooling will continue. TIMER: AUTO START/STOP FEATURE: When the unit is on or off, first press Timer button, the TIMER ON indicator light illuminates. It indicates the Auto Start program is initiated. When the time of TIMER ON is displayed ,press the Timer button again, the TIMER OFF indicator light illuminates. It indicates the Auto Stop program is initiated. Press or hold the UP or DOWN button to change the Auto time by 0.5 hour increments, up to 10 hours,then at 1 hour increments up to 24 hours.The control will count down the time remaining until start. The selected time will register in 5 seconds, and the system will automatically revert back to display the previous temperature setting or room temperature when the unit is on.(when the unit is off,there is no display.) Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop timed program. 10 AIR CONDITIONER FEATURES DISPLAYS: Temp Temp Displays Timer Timer DISPLAYS: Shows the set temperature in OC or OF and the Auto-timer settings.While on Fan only mode,it shows the room temperature. Error codes: AS-Room temperature sensor error-Unplug the unit and plug it back in.If error repeats, call for service. NOTE:In Fan only mode,it will display LO or HI . -Evaporator temperature sensor error-Unplug the unit and plug it back in.If error repeats, call for service. NOTE: is displayed as shown in the left picture. HS -Electric heating sensor error-Unplug the unit and plug it back in.If error repeats, call for service. NOTE: If the unit breaks off unexpectedly due to the power cut, it will restart with the previous function setting automatically when the power resumes. Air Directional Louvers Levers Fresh Air Vent Control (on 10000~12000Btu/h models): Fig. A (VENT CLOSED) Fig. B (VENT OPEN) The Fresh Air Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (See Fig.A) 2. Draw fresh air into the room- Vent Open (see Fig.B) 3. Exchange air from the room and draws fresh air into the room - Vent Fig. C (VENT & EXHAUST and Exhaust Open (see Fig.C) OPEN) CARE AND CLEANING Air Direction The louvers will allow you to direct the air flow Up or Down(on some models) and Left or Right throughout the room as needed. Pivot horizontal louvers until the desired Up/Down direction is obtained. CAUTION Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards. Move the Levers from side to side until the desired Left/Right direction is obtained. Air Filter Cleaning ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with. The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping.The fan will continue to run during this time. The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the other, press and hold the Left and Right Temp/Timer buttons at the same time, for 3 seconds. The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils. 11 CARE AND CLEANING Air Filter Cleaning Push the vent handle to the Vent Closed position (where applicable). Open the front panel. Take the filter by the center and pull up and out. Wash the filterusing liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure the filter is thoroughly dry before replacing. Or, instead of washing you may vacuum the filter clean. Note: Never use hot water over 40 C(104 F) to clean the air filter. Never attempt to operate the unit without the air filter. Cabinet Cleaning Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry. Never use harsh cleaners, wax or polish on the cabinet front. Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner. Plug in air conditioner. Winter Storage If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton. TROUBLESHOOTING TIPS Before calling for service, review this list. It may save your time and expense. This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance. Problem Air conditioner does not start Air from unit does not feel cold enough Air conditioner cooling, but room is too warm- ice forming on cooling coil behind decorative front. Solution Wall plug disconnected. Push plug firmly into wall outlet. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Plug Current Device Tripped. Press the RESET button. Power is OFF. Turn power ON. Room temperature below 62OF(17OC ). Cooling may not occur until room temperature rises above 62OF(17OC). Temperature sensing behind air filter element touching cold coil. Keep it from the cold coil. Set to a Lower temperature. Compressor stopped when changing modes. Wait for 3 minutes after set to the COOL mode. Outdoor temperature below 64OF(18OC). To defrost the coil, set FAN ONLY mode. Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY mode. Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a Higher setting. 12 TROUBLESHOOTING TIPS Problem Air conditioner cooling, but room is too warm- NO ice forming on cooling coil behind decorative front. Air conditioner turns on and off rapidly Noise when unit is cooling Solution Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section. Temperature is set too High, set temperature to a Lower setting. Air directional louvers positioned improperly. Position louvers for better air distribution. Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit. Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers. Unit recently turned on in hot room. Allow additional time to remove Stored heat from walls, ceiling, floor and furniture. Dirty air filter- air restricted. Clean air filter. Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past cooling coils more frequently. Air movement sound. This is normal . If too loud, set to a slower FAN setting. Window vibration - poor installation. Refer to installation instructions or check with installer. Water dripping INSIDE when unit is cooling. Water dripping OUTSIDE when unit is cooling. Remote Sensing Deactivating Prematurely (some models) Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to installation instructions - check with installer. Unit removing large quantity of moisture from humid room. This is normal during excessively humid days. Remote control not located within range. Place remote control within 20 feet & 180 , radius of the front of the unit. Remote control signal obstructed. Remove obstruction. Room too cold Set temperature too low. Increase set temperature. 13 The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details. CS356-UA(XD)NY XXXXXXXXX