Feath-R-Lite Stand Up Paddle Board
SUP Paddle
Your 3-Piece paddle easily connects together and is fully height adjustable. The ergonomic grip should be handled as illustrated (Figure 1).
If the connection at the lock of the propeller rod is loose, please rotate the lock several times and tighten it (Figure 2).
Figure 1: Illustration showing how to hold the ergonomic grip.
Figure 2: Illustration showing how to tighten the lock mechanism for the propeller rod.
Kayak Paddle
If your package came with a Kayak Conversion Kit (only available on select models), then the 3-Piece paddle easily converts into a kayak paddle using the extra blade. Simply swap the adjustable T-bar for the extra blade, pop into place and fasten the clasp.
Fin Type
There are three ways to install fins, which can be chosen according to the actual situation. Your SUP either has a Bravo Fin or Smart Lock Fin System. Please check your fin type and follow the necessary instructions.
TIP: Before you begin please ensure the fin box slot is clean and free of sand and grit.
Screw Fin
Figure 1: Illustration showing sliding the fin into the fin box, ensuring alignment of the fin and card slot.
Figure 2: Illustration showing placing the bolt in the chute and rotating tightly to secure the fin.
Slide Fin
Figure 1: Illustration showing sliding the fin into the fin box, ensuring alignment of the fin and card slot.
Figure 2: Illustration showing inserting the gasket into the slot to ensure it catches the fin.
US Fin
Figure 1: Illustration showing unscrewing the plate from the screw.
Figure 2: Illustration showing placing the plate into the fin slot via the gap.
Figure 3: Illustration showing inserting the fin into the fin box slot via the central gap, sliding it to the back, and pushing down the other end.
Figure 4: Illustration showing aligning the screw with the screw plate and tightening until secure.
TIP: Use the screw to slide the plate into place along the slot. Insert the fin into the fin box slot via the central gap, slide the fin to the back and firmly push down the other end (Figure 3). Line up the screw with the screw plate and tighten until fully secure (Figure 4).
Operation of Valves
In order to inflate easily, remove the valve cover (b) by turning it clockwise. Put it (a) in the "Output" position. After inflating, screw in the valve cover (b) by turning it anticlockwise.
Diagram showing valve components 'a' and 'b' and their positions.
WARNING: Please only use the pump provided or other recommended pumps. DO NOT use an air compressor as you will risk over-inflating the board and severely damaging your SUP beyond repair. Your warranty will be void in the event of damage via over-inflation.
Unpack and unroll your SUP on a smooth, clean, flat surface.
Connect the air tap on your pump to the inflation valve on your SUP. Firmly push the air tap inwards and twist clockwise to secure the connection.
Before you begin to pump, please consult the recommended PSI on the valve(s) of your SUP and inflate to the appropriate value. DO NOT over-inflate your SUP.
The PSI may not register on your pump until you reach at least 7 PSI - keep pumping!
Once the desired air pressure has been reached, please safely disconnect the air tap of your pump and secure the valve on your SUP.
Illustration showing connecting the pump to the SUP valve.
Illustration showing the pump securely connected to the valve.
Illustration showing pushing down on the valve to ensure proper seating.
Illustration of a pressure gauge showing PSI readings.
Safety & Care
For your own safety, please attach the coiled leash provided to your calf or ankle at all times. Secure one end to the D-ring at the rear of the board and securely attach the velcro strap to your calf or ankle.
Whilst paddling, please consider appropriate clothing for the weather or climate. It is highly recommended to wear a buoyancy aid vest or other personal flotation device, and a wetsuit in cooler conditions.
Stay hydrated by packing a water bottle in your cargo area. You can secure a bag or cooler under the cargo bungees with ease.
Store your mobile phone in the waterproof case provided. Also, consider packing a whistle or flashlight in case of an emergency.
Your board can expand and over-inflate in very hot temperatures. Please check the air pressure and deflate your board as necessary.
Please pack and store the SUP in the backpack provided, in a cool dry place and away from direct sunlight.
You should clean and maintain your board after each use. Hose down if necessary to prevent mildew build-up in storage. Do not use harsh chemicals for cleaning. Most dirt can be removed with mild soap and water.
A repair kit is provided, with extra patches and a valve tightening tool. From time-to-time your valve may need tightening to prevent any air leaks. To tighten the valve, first ensure that the board is fully deflated. Insert the tool into the valve and push upwards from the underside of the board to ensure that the valve is making firm contact with the thread. Next, turn the tool clockwise until the valve is fully tightened and secure.
Please ensure that no water gets inside of your SUP as this can severely damage the board. Drain any water and dry thoroughly before re-attaching the valve and inflating.