Netum L5 Barcode Scanner Setup Guide

Connection Mode

Working via USB cable

Get Started: Connect scanner with your device via USB cable. If you use a US keyboard, it's a plug and play model. If you use other types of keyboards, please refer to the "Keyboard Language Type" section to set the keyboard language before use.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and communications settings. To change these settings, programming is accomplished by scanning the barcodes in this guide. An asterisk (*) next to an option indicates the default setting.

Restore factory default

Scan the following barcodes one by one to restore the scanner to factory defaults. (Four steps included)

Communication Interfaces

USB HID-KBW

When you connect the engine to the Host via a USB connection, you can enable the USB HID-KBW feature by scanning the barcode below. Then, the engine's transmission will be simulated as USB keyboard input. The Host receives keystrokes on the virtual keyboard. It works on a Plug and Play basis and no driver is required.

USB COM Port Emulation

If you connect the scanner to the Host via a USB connection, the USB COM Port Emulation feature allows the host to receive data in the way a serial port does. A driver is required for this feature.

Keyboard Language

In order to let the scanner upload codes in a correct way, you have to set the keyboard language before you use it.

For example: If you use a French Keyboard, just scan the barcode of "French Keyboard". After that, the scanner will upload barcodes according to the French keyboard layout. American Keyboard is set by default; if you use a US keyboard, you can skip this part.

Scan Mode

Trigger Mode (Default)

Scanning this barcode will enable the scanner to enter manual trigger mode.

Continuous Mode

This mode enables the engine to scan/capture, decode and transmit over and over again.

Auto Sense Mode

Scanning this barcode will enable the scanner to enter auto sense mode.

Terminator

The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.

Beeper

To enable or disable beep for successful scan, please scan the appropriate barcode below.

Beep Volume

Beep volume can be adjusted by scanning below command barcodes accordingly.

Convert Case

Scan the appropriate barcode below to convert barcode data to your desired case.

Ctrl Combine-Key Set

Enable/Disable All Symbologies

If the Disable All Symbologies feature is enabled, the engine will not be able to read any non-programming barcodes except the programming barcodes.

Enable/Disable 1D Symbologies

If the Disable 1D Symbologies feature is enabled, the engine will not be able to read any 1D barcodes.

Enable/Disable 2D Symbologies

If the Disable 2D Symbologies feature is enabled, the engine will not be able to read any 2D barcodes.

Transmit Code ID Character

A code ID character identifies the code type of a scanned barcode. This can be useful when decoding more than one code type. The code ID character is inserted between the prefix character (if selected) and the decoded symbol.

AIM Code Identifiers

Each AIM Code Identifier contains the three-character string ]cm where: ] = Flag Character, c = Code Character (see Table 4-4), m = Modifier Character.

Symbol Code ID Identifiers

Table 4-4

Read 1D Normal barcode/ Reversal barcode

UPC/EAN

Enable/Disable UPC-A

To enable or disable UPC-A, scan the appropriate barcode below.

Enable/Disable UPC-E

To enable or disable UPC-E, scan the appropriate barcode below.

Enable/Disable EAN-8

To enable or disable EAN-8, scan the appropriate barcode below.

Enable/Disable EAN-13

To enable or disable EAN-13, scan the appropriate barcode below.

Enable/Disable Bookland EAN(ISBN)

To enable or disable EAN Bookland, scan the appropriate barcode below.

Decode UPC/EAN Supplementals UPC/EAN

Supplementals are barcodes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2, EAN 13+5). The following options are available:

Transmit UPC-A Check Digit

Scan the appropriate barcode below to transmit the symbol with or without the UPC-A check digit.

Transmit UPC-E Check Digit

Scan the appropriate barcode below to transmit the symbol with or without the UPC-E check digit.

Convert UPC-E to UPC-A

Enable this parameter to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, data follows UPC-A format and is affected by UPC-A programming selections.

EAN-8 Zero Extend

When enabled, this parameter adds five leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols.

Code 128

Enable/Disable Code 128

To enable or disable Code 128, scan the appropriate barcode below.

Enable/Disable GS1-128

To enable or disable GS1-128, scan the appropriate barcode below.

Enable/Disable ISBT 128

To enable or disable ISBT 128, scan the appropriate barcode below.

Code39

Enable/Disable Code 39

To enable or disable Code 39, scan the appropriate barcode below.

Code 39 Check Digit Verification

When this feature is enabled, the scan engine checks the integrity of all Code 39 symbols to verify that the data complies with specified check digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded. Only enable this feature if your Code 39 symbols contain a module 43 check digit.

Transmit Code 39 Check Digit

Transmit Code 39 Check Digit (Enable)

Scan this symbol to transmit the check digit with the data.

Scan this symbol to transmit data without the check digit.

Convert Code 39 to Code 32

Code32 Prefix

Enable this parameter will add prefix "A" to all Code 32. Before enabling this parameter, you must first convert Code 39 to Code 32 (Italian pharmaceutical code).

Enable/Disable Code 39 Full ASCII

Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set.

NOTE: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If you get an error beep when enabling Code 39 Full ASCII, disable Trioptic Code 39 and try again.

Code 93

To enable or disable Code 93, scan the appropriate barcode below.

Set Lengths for Code 93

The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range.

Any Length - Scan this option to decode Code 93 symbols containing any number of characters.

Code 11

Enable/Disable Code 11

To enable or disable Code 11, scan the appropriate barcode below.

Set Lengths for Code 11

The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specific range.

Any Length - Scan this option to decode Code 11 symbols containing any number of characters within the scan engine capability.

Code 11 Check Digit Verification

This feature allows the scan engine to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit algorithm. This selects the check digit mechanism for the decoded Code 11 bar code. The options are to check for one check digit, check for two check digits, or disable the feature.

Transmit Code 11 Check Digits

Interleaved 2 of 5/ITF

Enable/Disable Interleaved 2 of 5

To enable or disable Interleaved 2 of 5, scan the appropriate barcode below.

Set Lengths for Interleaved 2 of 5

Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.

Convert I 2 of 5 to EAN-13

This parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. To accomplish this, I 2 of 5 must be enabled, one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check digit.

Discrete 2 of 5/Industrial 2 of 5/IND25

Enable/Disable Discrete 2 of 5

To enable or disable Discrete 2 of 5, scan the appropriate barcode below.

Matrix 25

Enable/Disable Matrix 25

To enable or disable Matrix 25, scan the appropriate barcode below.

Standard 25/IATA 25

Enable/Disable Standard 25

To enable or disable Standard 25, scan the appropriate barcode below.

Standard 25 Check Digit Verification

Transmit Check Character

Codabar

Enable/Disable Codabar

To enable or disable Codabar, scan the appropriate barcode below.

MSI/MSI PLESSEY

Enable/Disable MSI

To enable or disable MSI, scan the appropriate barcode below.

GS1 DataBar/RSS

Enable/Disable GS1 DataBar-14

To enable or disable GS1 DataBar-14, scan the appropriate barcode below.

Enable/Disable GS1 DataBar Limited

To enable or disable GS1 DataBar Limited, scan the appropriate barcode below.

Enable/Disable GS1 DataBar Expanded

To enable or disable GS1 DataBar Expanded, scan the appropriate barcode below.

PDF417

Scan normal or mirror image picture.

Enable/Disable PDF417

To enable or disable PDF417, scan the appropriate barcode below.

Read Normal Phase/ Phase Reversal

QR

Read normal phase/ phase reversal/ mirror image picture.

Enable/Disable QR

To enable or disable QR, scan the appropriate barcode below.

Data Matrix(DM)

Scan normal or mirror image picture.

Enable/Disable Data Matrix(DM)

To enable or disable Data Matrix(DM), scan the appropriate barcode below.

Read Normal Phase/ Phase Reversal

Maxi Code

Enable/Disable Maxi Code

To enable or disable Maxi Code, scan the appropriate barcode below.

Aztec Code

Enable/Disable Aztec Code

To enable or disable Aztec Code, scan the appropriate barcode below.

Han Xin Code

Enable/Disable Han Xin Code

To enable or disable Han Xin Code, scan the appropriate barcode below.

Read Normal Phase/ Phase Reversal

Prefix/Suffix Values

A prefix and/or one or two suffixes can be appended to scan data for use in data editing. To set these values, scan a four-digit number (i.e., four bar codes) that corresponds to ASCII values. See the Table 4-3 and Numeric Bar Codes in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix. To set the Prefix/Suffix values via serial commands, see Setting Prefixes and Suffixes Via Serial Commands.

Scan Data Transmission Format

To change the Scan Data Transmission Format, scan one of the eight barcodes corresponding to the desired format.

Appendix 1: Numeric Bar Codes

For parameters requiring specific numeric values, scan the appropriately numbered barcode(s).

Barcode: 0

Barcode: 1

Barcode: 2

Barcode: 3

Barcode: 4

Barcode: 5

Barcode: 6

Barcode: 7

Barcode: 8

Barcode: 9

Cancel

To change the selection or cancel an incorrect entry, scan the barcode below.

Scan Value / ASCII Value Mapping

Support

For any inquiries concerning our products, please send an email to service@netum.net, and we will respond to you as soon as possible.

Contact Information

Tel.: +0086 20-3322-8813

Email: service@netum.net

Whatsapp: +86 188 2626 1132

Website: www.netum.net

Address: Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan Avenue.