Assembly Instructions for Dining Furniture Set
Dining Bench
Model Number: N752P312415
Part List:
| Part | Description | Quantity |
|---|---|---|
| D | Bench top | 1 PC |
| E | Bench Legs | 4 PCS |
Hardware List:
| Item | Description | Quantity |
|---|---|---|
| 1 | BOLT (Ø1/4 x 60mm) | 8 PCS |
| 2 | Spring Washer (Ø1/4 x 13mm) | 8 PCS |
| 3 | Flat Washer (Ø1/4 x 19mm) | 8 PCS |
| 4 | Allen key (4mm) | 1 PC |
Assembly Steps:
Attach each Leg (E) to the underside of the Bench top (D).
For each leg, use two BOLT (1), two Spring Washers (2), and two Flat Washers (3).
Insert the BOLT through the Spring Washer, then the Flat Washer, and into the pre-drilled holes.
Tighten using the Allen key (4).
Note: Once all legs are attached, ensure the bench is level and tighten all hardware securely.
Dining Chair
Model Number: N752P312415
Part List (For One Chair):
| Part | Description | Quantity |
|---|---|---|
| A | Chair top | 1 PC |
| B | Chair Back | 1 PC |
| C | Front Leg | 2 PCS |
Hardware List (For One Chair):
| Item | Description | Quantity |
|---|---|---|
| 1 | BOLT (Ø1/4 x 75mm) | 4 PCS |
| 2 | Spring Washer (Ø1/4 x 13mm) | 10 PCS |
| 3 | Flat Washer (Ø1/4 x 19mm) | 10 PCS |
| 4 | Allen key (4mm) | 1 PC |
| 5 | BOLT (Ø1/4 x 40mm) | 2 PCS |
| 6 | BOLT (Ø1/4 x 60mm) | 4 PCS |
Assembly Steps:
Step 1: Attach Seat and Back to Legs
Attach two Legs (C) to the underside of the Chair top (Seat) (A) using one BOLT (5), one Spring Washer (2), and one Flat Washer (3) per leg. Tighten using the Allen key (4).
Attach the Chair Back (B) to the Chair top (Seat) (A) using four BOLT (1), six Spring Washers (2), and six Flat Washers (3). Tighten using the Allen key (4).
Step 2: Attach Remaining Legs
Attach the remaining two Legs (C) to the chair assembly using four BOLT (6), four Spring Washers (2), and four Flat Washers (3). Tighten using the Allen key (4).
Step 3: Final Tightening
Note: Ensure the chair is level and tighten all hardware securely.
Dining Table
Model Number: N752P312414
Part List:
| Part | Description | Quantity |
|---|---|---|
| A | Table top | 1 PC |
| B | Table Legs | 4 PCS |
Hardware List:
| Item | Description | Quantity |
|---|---|---|
| 1 | BOLT (Ø5/16 x 75mm) | 8 PCS |
| 2 | Spring Washer (Ø5/16 x 13mm) | 8 PCS |
| 3 | Flat Washer (Ø5/16 x 19mm) | 8 PCS |
| 4 | Allen key (4mm) | 1 PC |
Assembly Steps:
Step 1: Prepare Table Top
Place the Table top (A) upside down on a protected surface.
Remove any protective blocks from the underside.
Step 2: Attach Legs
Illustration shows the table top upside down with four legs to be attached. A close-up view details the hardware used for securing a leg.Attach each Table Leg (B) to the underside of the Table top (A).
For each leg, use two BOLT (1), two Spring Washers (2), and two Flat Washers (3).
Insert the BOLT through the Spring Washer, then the Flat Washer, and into the pre-drilled holes.
Tighten using the Allen key (4).
Note: Once all legs are attached, ensure the table is level and tighten all hardware securely.
