FT-RSA-HA9-[FT-DC3-HC]-EN 20180914 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2014-2015 ACURA RLX PTS AT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
A
B
PAGE 2 OF 10 20180914
T001_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 1 NOT REQUIRED FOR BASIC INSTALLATION.
M4
INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL
M6
OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) PINK - 08
1: BLUE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T001_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T001_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) PINK - 08
1: BLUE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B A
PAGE 5 OF 10 20180914
T001_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T001_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) RED - 06 CANL (DATA) WHITE - 07
PTS (+) GRAY - 12 12V (+) PINK - 14 GROUND (-) BROWN - 15 S-NET (DATA) RED - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) DKBLUE - 11 START (+) BLUE -18
ACCESSORY (+) ORANGE - 24
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) PINK - 08
1: LT BROWN
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: BLUE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2014-2015 Acura RLX PTS AT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2014-2015 Acura RLX PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Acura RLX PTS AT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2013-2015 HONDA ACCORD CROSSTOUR PTS AT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
A
B
PAGE 2 OF 10 20180914
T003_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 1 NOT REQUIRED FOR BASIC INSTALLATION.
M4
INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL
M6
OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR GRAY
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T003_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T003_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
1: 28 PIN PTS CONNECTOR GRAY 1: 28 PIN PTS HARNESS
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B A
PAGE 5 OF 10 20180914
T003_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T003_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) BLUE - 12 12V (+) WHITE - 14 GROUND (-) BROWN - 15 S-NET (DATA) LTGREEN - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) WHITE - 11 START (+) LTGREEN -18
ACCESSORY (+) GRAY - 24
LIGHTS OFF (-) RED - 01 PARKING LIGHTS (-) GRAY - 08
1: GRAY
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: WHITE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2015 Honda Accord Crosstour PTS AT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2013-2017 HONDA ACCORD PTS AT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
A
B
PAGE 2 OF 10 20180914
T002_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 1 NOT REQUIRED FOR BASIC INSTALLATION.
M4
INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL
M6
OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T002_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T002_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B A
PAGE 5 OF 10 20180914
T002_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T002_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) BLUE - 12 12V (+) WHITE - 14 GROUND (-) BROWN - 15 S-NET (DATA) GRAY - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) WHITE - 11 START (+) BLUE -18
ACCESSORY (+) GRAY - 24
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
1: LT BROWN
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: WHITE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2013-2017 Honda Accord PTS AT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2013-2017 Honda Accord PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS AT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2013-2017 HONDA ACCORD PTS MT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
A
B
D
PAGE 2 OF 10 20180914
T006_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
MANDATORY STEPS FOR MANUAL TRANSMISSION: 1- DO NOT CUT THE LOOP. 2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR. 3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION.
1 NOT REQUIRED FOR BASIC INSTALLATION. INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
CLUTCH (-) BROWN - 02
HORN (-) HOOD SWITCH 2
1: YELLOW
12
HEADLAMP SWITCH (C) CLUTCH SWITCH (D)
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T006_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
MANDATORY STEPS FOR MANUAL TRANSMISSION:
M1
1- DO NOT CUT THE LOOP.
M5
2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR.
M4
3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION.
M6
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T006_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
1: 28 PIN PTS CONNECTOR LT BROWN
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
CLUTCH (-) BROWN - 02
HORN (-) HOOD SWITCH 2
1: YELLOW
12
HEADLAMP SWITCH (C) CLUTCH SWITCH (D)
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B A
C
PAGE 5 OF 10 20180914
T006_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
MANDATORY STEPS FOR MANUAL TRANSMISSION: M1 1- DO NOT CUT THE LOOP. M5 2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR. M4 3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION. M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T006_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) BLUE - 12 12V (+) WHITE - 14 GROUND (-) BROWN - 15 S-NET (DATA) GRAY - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) WHITE - 11 START (+) BLUE -18
ACCESSORY (+) GRAY - 24
LIGHTS OFF (-) PINK - 01 PARKING LIGHTS (-) GRAY - 08
CLUTCH (-) BROWN - 02
1: LT BROWN
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: WHITE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
1: YELLOW
12
CLUTCH SWITCH (C)
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2013-2017 Honda Accord PTS MT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2013-2017 Honda Accord PTS MT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2013-2017 Honda Accord PTS MT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2015-2016 HONDA CR-V PTS AT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A C
B
PAGE 2 OF 10 20180914
T005_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 1 NOT REQUIRED FOR BASIC INSTALLATION.
M4
INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL
M6
OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR GRAY
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) BLUE - 08
1: GRAY
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T005_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T005_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
1: 28 PIN PTS CONNECTOR GRAY 1: 28 PIN PTS HARNESS
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) BLUE - 08
1: GRAY
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A B
PAGE 5 OF 10 20180914
T005_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T005_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) PURPLE - 12 12V (+) RED - 14
GROUND (-) BROWN - 15 S-NET (DATA) YELLOW - 21
IGNITION 2 (+) BLUE - 28
IGNITION 1 (+) BLUE - 11 START (+) RED -18
ACCESSORY (+) TAN - 24
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) BLUE - 08
1: GRAY
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: GRAY
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2015-2016 Honda CR-V PTS AT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2015-2016 Honda CR-V PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2015-2016 Honda CR-V PTS AT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2014-2015 HONDA CIVIC PTS AT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
B
A
PAGE 2 OF 10 20180914
T004_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 1 NOT REQUIRED FOR BASIC INSTALLATION.
M4
INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL
M6
OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR GRAY
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T004_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T004_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
1: 28 PIN PTS CONNECTOR GRAY 1: 28 PIN PTS HARNESS
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
HEADLAMP SWITCH (C)
HORN (-) HOOD SWITCH 2
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B
A
PAGE 5 OF 10 20180914
T004_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
!
! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOTT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOTT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T004_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) GREEN - 12 12V (+) WHITE - 14 GROUND (-) BLACK - 15 S-NET (DATA) LTGREEN - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) WHITE - 11 START (+) ORANGE -18
ACCESSORY (+) GRAY - 24
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
1: GRAY
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: WHITE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2014-2015 Honda Civic PTS AT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2014-2015 Honda Civic PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS AT www.idatalink.com
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
INSTALL GUIDE
2014-2015 HONDA CIVIC PTS MT
DOCUMENT NUMBER
REVISION DATE 20180914
FIRMWARE FT-RSA-HA9-[FT-DC3-HC]
HARDWARE FT-DC3-HC
ACCESSORIES ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
TERMS OF USE
Automotive Data Solutions Inc. ("ADS") products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician's responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.
www.idatalink.com
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
C
B
A
D
PAGE 2 OF 10 20180914
T007_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA9)
PAGE 3 OF 10 20180914
M1
M5 M4 M6 M2 M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
MANDATORY STEPS FOR MANUAL TRANSMISSION: 1- DO NOT CUT THE LOOP. 2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR. 3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION.
1 NOT REQUIRED FOR BASIC INSTALLATION. INSERT WIRE TERMINALS IN BLACK 12 PIN CONNECTOR FOR OPTIONAL OUTPUTS. REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
M2 01 02 03 04 05 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 02 03 04 05 06 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 09 10
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
MS4
3
MS5
RELAY
DO NOT CONNECT MS4 OR MS5 IF 3 THE VEHICLE IS NOT EQUIPPED WITH A
STEERING COLUMN LOCK.
SMART PCU (A)
VS2
1
2
1: 28 PIN PTS CONNECTOR GRAY
1: 28 PIN PTS HARNESS VS1
VS4 2: 24 PIN IGNITION CONNECTOR GRAY
2: 24 PIN IGNITION HARNESS VS3
VEHICLES WITH STEERING COLUMN LOCK ONLY VS6
VS5
STEERING COLUMN LOCK, SILVER BOX (B) 1: STEERING COLUMN LOCK MODULE CONNECTOR 1: STEERING COLUMN LOCK MODULE HARNESS - GRAY
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
CLUTCH (-) ORANGE - 02
HORN (-) HOOD SWITCH 2
1: YELLOW
12
HEADLAMP SWITCH (C) CLUTCH SWITCH (D)
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
T007_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
MANDATORY STEPS FOR MANUAL TRANSMISSION:
M1
1- DO NOT CUT THE LOOP.
M5
2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR.
M4
3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION.
M6
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01
02
03
04
05
06
07
08 09
MS1
10
11
12
13
14
15
16
17
18
19
20
M5 01
02
MS2
03
04
05
06
RELAY
T007_H
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
T-HARNESS / WIRING DIAGRAM - 1 OF 1 (ADS-THR-HA6)
VS2 VS1 VS4 VS3
1: 28 PIN PTS CONNECTOR GRAY 1: 28 PIN PTS HARNESS
PAGE 4 OF 10 20180914
SMART PCU (A)
1
2
2: 24 PIN IGNITION CONNECTOR GRAY 2: 24 PIN IGNITION HARNESS
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
1: WHITE
654321 12 11 10 9 8 7
CLUTCH (-) ORANGE - 02
HORN (-) HOOD SWITCH 2
1: YELLOW
12
HEADLAMP SWITCH (C) CLUTCH SWITCH (D)
IMPORTANT: 1 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
INSTALL THE SUPPLIED HOOD SWITCH IF 2 THE VEHICLE IS NOT EQUIPPED WITH ONE.
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
B
A
C
PAGE 5 OF 10 20180914
T007_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
MANDATORY STEPS FOR MANUAL TRANSMISSION:
M1
1- DO NOT CUT THE LOOP.
M5
2- CONNECT THE MANUAL TRANSMISSION DIGITAL SENSOR.
M4
3- SEE THE PRODUCT GUIDE FOR MORE INFORMATION.
M6
M2
M3
M1 01 ORANGE 02 RED 03 PURPLE 04 PINK/WHITE 05 PINK 06 WHITE 07 RED 08 BLACK
M2 01 GREEN·BLACK DOT 02 BLUE·BLACK DOTT 03 RED/WHITE·BLACK DOT 04 GREEN/WHITE·BLACK DOT 05 GREEN/BLACK·BLACK DOTT 06 BLUE/WHITE·BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE·BLACK DOT - STARTER (-) OUTPUT 09 PURPLE/BLACK·BLACK DOT 10 WHITE/BLACK·BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK·BLACK DOT 12 WHITE·BLACK DOT - PARKING LIGHTS (-) OUTPUT
M3 01 BROWN·SILVER DOT 02 BLACK/WHITE·SILVER DOT 03 PURPLE·SILVER DOT 04 GREEN·SILVER DOT 05 PURPLE/WHITE·SILVER DOT 06 WHITE/BLUE·SILVER DOT 07 GRAY·SILVER DOT - HOOD (-) INPUT 08 BLUE·SILVER DOT 09 GRAY/BLACK·SILVER DOT 10 EMPTY
M4 01 EMPTY 02 EMPTY 03 BROWN/RED - CANH 1 04 BROWN/YELLOW - CANL 1 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN - ACCESSORY (+) IN/OUT 16 ORANGE/BLACK - S-NET (DATA) 17 PINK - IGNITION (+) IN/OUT 18 PURPLE - STARTER (+) OUTPUT 19 RED - 12V (+) INPUT 20 BLACK - GROUND (-)
M5 01 GRAY/BLACK·BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE 02 WHITE/BLACK·BLUE DOT 03 GRAY/RED·BLUE DOT - IGNITION 2 (+) VEHICLE SIDE 04 WHITE/RED·BLUE DOT 05 GRAY·BLUE DOT 06 WHITE·BLUE DOT
T007_W
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
HARDWIRE / WIRING DIAGRAM - 1 OF 1
CANH (DATA) PINK - 06 CANL (DATA) BLUE - 07
PTS (+) GREEN - 12 12V (+) WHITE - 14 GROUND (-) BLACK - 15 S-NET (DATA) LTGREEN - 21 IGNITION 2 (+) YELLOW - 28
IGNITION 1 (+) WHITE - 11 START (+) ORANGE -18
ACCESSORY (+) GRAY - 24
LIGHTS OFF (-) ORANGE - 01 PARKING LIGHTS (-) GRAY - 08
CLUTCH (-) ORANGE - 02
1: GRAY
PAGE 6 OF 10 20180914
SMART PCU (A)
1
2
14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 27 26 25 24 23 22 21 20 19 18 17 16 15
2: GRAY
12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13
1: WHITE
HEADLAMP SWITCH (B)
654321 12 11 10 9 8 7
1: YELLOW
12
CLUTCH SWITCH (C)
HORN (-) HOOD SWITCH 1
INSTALL THE SUPPLIED HOOD SWITCH IF 1 THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT: 2 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
01
Set ignition to ON position.
OFF ACC ON START
ENGINE START STOP
02
Wait, LED 1 will flash GREEN rapidly.
MODULE PROGRAMMING PROCEDURE - 1 OF 1
07
Set ignition to ON position.
12
OFF ACC ON START
ENGINE START STOP
08
Wait, LED 1 will turn solid GREEN for 2
13
seconds.
03
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
09
Set ignition to OFF position.
OFF ACC ON START
ENGINE START STOP
14
04
WARNING: Disconnect power last. Disconnect
10
Press UNLOCK on the OEM remote.
15
module from vehicle.
05
Connect module to computer and proceed
>>
If the vehicle is equipped with a power liftgate:
16
with extended programming.
Open and close the power liftgate with the
OEM keyfob.
06
Connect power first. Connect module to
11
START vehicle for 15 seconds.
vehicle.
OFF ACC ON START
ENGINE START STOP
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 7 OF 10 20180914
Press and hold the brake pedal.
Press and release the module's programming button. Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
2014-2015 Honda Civic PTS MT www.idatalink.com
T-HARNESS / TAKEOVER PROCEDURE - 1 OF 1
>>
The takeover procedure is only functional with
06
Take over procedure completed.
an ADS-THR-HA9 T-harness installation. All
vehicle doors must be closed and locked prior
to remote start sequence.
01
Time restriction. Complete steps 2 to 5 within
>>
Failure to follow procedure will result in
45 seconds.
vehicle engine shutdown.
02
Press unlock on OEM or aftermarket remote
or request switch.
03
Open driver door and enter vehicle.
04
Close driver door.
05
Press and release BRAKE pedal.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
PAGE 8 OF 10 20180914
2014-2015 Honda Civic PTS MT www.idatalink.com
INSTALLATION CHECKLIST - 1 OF 2
PAGE 9 OF 10 20180914
CHECKLIST - WITH AFTERMARKET KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock? YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock?
YES: Go to next step.
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
11 Open hood.
12
If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start?
YES: Go to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal.
Question 10: Does the vehicle shut down? YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle. 20 Installation checklist completed.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
INSTALLATION CHECKLIST - 2 OF 2
PAGE 10 OF 10 20180914
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal.
Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle. 15 Installation checklist completed.
U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2018
FT-RSA-HA9-[FT-DC3-HC]-EN
2014-2015 Honda Civic PTS MT www.idatalink.com
pdftk 2.02 - www tk.com itext-paulo-155 (itextpdf.sf.net-lowagie.com)