Digi Technical Support: Digi offers multiple support plans to help you get the most out of your product. For information on Technical Support plans and pricing, ...
PortServer TS M MEI Quick Start Guide Author: Digi International Inc. Subject: PortServer TS M MEI Quick Start Guide 90000688 Keywords: PortServer TS M MEI Quick Start Guide, Digi International, 90000688 Created Date: 11/18/2019 9:11:53 AM
Quick Start Guide PortServer® TS M MEI Welcome to your Digi product Get started: This guide helps you with initial product setup. Need more? Find additional supporting material for this product at www.digi.com/support/portservertsmmei. Or connect to the online documentation by scanning this code: 1 Verify your components Digi Technical Support: Digi offers multiple support plans to help you get the most out of your product. For information on Technical Support plans and pricing, contact us at 877.912.3444 or visit www.digi.com/support. Documentation feedback: To provide feedback on this documentation, send your comments to techcomm@digi.com. Included equipment PortServer TS M MEI RJ-11 phone cord DB-9 - RJ-45 adapter (available with some models) Required additional equipment Power supply Power supply adapters 2 Ethernet cable Note A loose label sticker that includes the unique device password is included in the box. Retain this label sticker with your hardware records. This default password will be needed if the device is factory reset and you want to access the web UI on the device. 2 Set DIP Switch For each serial port on the PortServer, set the serial DIP switch according to your serial device requirements (EIA-232/422/485). Pinout information is included in this Quick Start Guide. For initial configuration, via the serial port, use of the EIA-232 settings is recommended. Note If switch 4 is up, the termination resistor is connected. If switch 4 is down, the termination resistor is not connected. PortServer TS 1-4 port DIP Switch settings Switch settings Up/On Down/Off 3 Connect the hardware 1. Connect phone line to modem. 2. Connect serial device and a straight through CAT 5 cable. 3. Connect Ethernet cable. 4. Connect power supply. LEDs and startup status: All LEDs flash on startup. © 2019 Digi International Inc. Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the property of their respective owners. n Link LED: (green) On: Physical network detected. n Power LED: (green) Steady blinking: seeking or waiting for an IP address. n CD/ACT LED: (yellow) Modem carrier detect; modem is online. n ACT LED: (yellow): l ON: Bad Initialization l OFF: Ready l BLINKING: network activity 4 Download required software Digi provides several utilities that discover devices present on a network. You will need to download the Device Discovery Utility. 1. Navigate to: www.digi.com/support/portservertsmmei. 2. Scroll down and click Product Support. 3. Click Utilities. 4. Under Operating System Specific Utilities, select your operating system. A list of available drivers appears. 5. Download and run Device Discovery Utility. If you will use Digi's RealPort software to manage the serial ports for your products, download the RealPort software. 1. Navigate to: www.digi.com/support/portservertsmmei. 2. Scroll down and click Product Support. 3. Click Drivers. 4. Under Operating System Specific Drivers, select your operating system. A list of available downloads and release notes appears. 5. Download the RealPort driver and the release notes. Note For Windows operating systems, unzip the download package and run the executable. For Linux or Unix operating systems, follow instructions in the release notes. 5 Configure the serial ports 1. Navigate to www.digi.com/support/portservertsmmei. 2. Download and install the Digi Discovery Utility. a. Click Product Support > Utilities. b. From the Operating System Specific Utilities list box, select your operating system. c. Click Device Discovery Utility for Windows to download the utility. d. Click the downloaded utility to install it. 3. Use Digi Discovery Utility to discover devices on your network and open the web interface: a. In the list of discovered devices, select the PortServer TS M MEI device. Configure the IP address, if necessary. b. Click Open web interface. c. A login prompt for the web interface appears. Enter the default user name: root. The default password is printed on the device label. If a password is not on the device label, the default password is dbps. If neither password works, the password may have been changed. Contact your system administrator. 4. Configure serial port settings using port profiles. Port profiles are a defined set of serial port parameters for a particular use. For PortServer TS M MEI products, Digi recommends the RealPort port profile. To configure ports to use the RealPort port profile: a. In the web interface, under Configuration, click Serial Ports. b. On the Serial Port Configuration page, click the port to be configured and click Change Profile. c. In the list of profiles, select the RealPort port profile, then click Apply. d. For EIA-232 devices that will be connected using 8-wire cables, configure the Altpin setting. The default for this setting is off; it must be enabled as needed for each serial port. For each applicable serial port, click Advanced Serial Settings and select the Enable DCD on 8-pin RJ45 connectors (Altpin) setting, then click Apply. 6 Pinoutsmadbuild