Spectrum Brands, Inc. 450241CBR Z-Wave Plus Module NUL450241CBR NUL450241CBR 450241cbr
66071-001 Rev 01 Z-Wave® Plus ENGLISH Installation and User Guide Required tools 4 AA Batteries Ruler Phillips head screwdriver Additional Tools (depending on application) Hammer Wood block Kwikset Technical Support 1-866-863-6584 www.kwikset.com Parts in the box Latch Exterior Assembly A F W B "B" is not included. If needed, please contact Kwikset to order a drive-in latch for your lock. Mounting Plate Strike C Keys Adapter ring D E SmartKey Tool Interior Assembly K Fasteners 03809 G N P 48654 T H L M 46780 Q S 27526 U 64109 V 1 Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep. A Measure to confirm that the hole in the door is either 2-1/8" (54 mm) or 1-1/2" (38 mm). B Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70 mm). C Measure to confirm that the hole in the door edge is 1" (25 mm). 2-1/8" 54 mm or 1-1/2" 38 mm 2-3/8" or 2-3/4" 60 or 70 mm backset 1" 25 mm Note: Additional door preparation may be required for doors with 1-1/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep. D Measure to confirm that the door is between 1-3/8" and 1-3/4"* (35 mm and 44 mm*) thick. 1-3/8" 1-3/4"* 35 44 mm* *Service kits for 2-1/4" (57 mm) thick doors are available through Kwikset. 2 Install the latch and strike actual size N P Q A Is the door edge chiseled? YES NO or chiseled not chiseled Use latch "A". If the latch bolt is not already extended, extend the latch bolt as shown. Use latch "B" (not included). If the latch bolt is not already extended, extend the latch bolt as shown. A B B Hold the latch in front of the door hole, with the latch face flush against the door edge. A B C Is the D-shaped hole centered in the door hole? YES NO or S D Which latch are you installing? Latch "A" or Latch "B" B A N or P (2x) wood block D-shaped hole No adjustment is required. Proceed to next step. D-shaped hole Rotate latch face as shown to extend latch. A B E Install strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep. Longer screws install closest to the door jamb. S (2x) Q (2x) C door frame 1 / 4 3 Install the exterior keypad A Insert cylinder into keypad. F W B What is the diameter of the hole in the door? Diameter is 2-1/8" (54 mm) Diameter is 1-1/2" (38 mm) or 2-1/8" 54 mm 1-1/2" 38 mm "D" is required for installation. Install "D" on "F". F D "D" is not needed for installation. Discard "D". D actual size T C Install exterior keypad and mounting plate. a b Locate screws and keep them within reach. c Support exterior assembly during mounting plate installation. G F T Cable goes underneath latch. d e Keep parallel to edge of door. T T (2x) Tighten screws evenly. Route cable through center hole, then push cable into side hole. E Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (T). Remove key when finished and make sure the latch bolt is fully extended. 4 Install the interior assembly A Remove battery cover. M L B Remove battery pack. K Do not install batteries until step 5. actual size U C Make sure the turnpiece is in the vertical position. L vertical D Connect cable. Ensure tight cable connection. E Lay cable flat against the interior housing. F Push turnpiece shaft onto torque blade. G Secure interior assembly with supplied screws. L torque blade turnpiece shaft U (2x) Note: Turnpiece may not rotate smoothly until after step 5. 5 Install the batteries and perform the door handing process This step will teach your lock the orientation of your door and is crucial to lock operation. A Install 4 AA batteries in battery pack. B Press and HOLD the Lock button while installing battery pack. Hold button until the latch bolt starts moving on its own. K Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only. 2 / 4 C Did the latch bolt retract and extend on its own when the battery pack was installed? YES or Door handing process was successful! Proceed to next step after latch bolt stops moving. NO Remove battery pack, wait 15 seconds, then attempt the process again. 6 Pair the lock with your smart home system If your controller is S2-compatible, please refer to the S2 Pairing Guide on the SmartCode 910 page at www.kwikset.com. A Initiate the pairing process at your smart home controller. Refer to your smart home system instructions for more information. B When prompted by your smart home system to initiate pairing at the lock, press button "A" on the lock interior one time. The red LED will illuminate when pairing mode has been entered. button "A" Please allow time for the controller to pair with the lock. C If the pairing process is successful, re-name the lock in your system (if applicable). D If pairing is unsuccessful, follow your system's instructions to remove the lock from the controller and any other network, then press button "A" on the lock one time. Perform steps 6A-6C again. If pairing is still unsuccessful, consult the Programming and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com. 7 Add user codes (30 max) It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here. A Make sure the door is open. Press the Program button the number of times that corresponds to the user code position being programmed. Programming Timeout If no button is pressed for five seconds, the system will time out and you will need to restart the procedure. Example: If programming the third code, press the button three times. B Enter user code. A total of 30 user codes may be programmed. C Press Lock button once. Each user code must be a unique code between 4 and 8 digits, depending on your smart home system. D What lights and sounds does the lock produce? One green flash with one beep* Three red flashes with three beeps* or or green 1x red 3x Two beeps* 2x Programming was successful. Programming was unsuccessful. Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Programming time out. Make sure not to pause for more than 5 seconds during programming. *Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See "Switches and Status LED Colors" on page 4. Mastercode For enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com. 8 Test the lock (review normal operation) Confirm that the code(s) added in previous step can unlock the door. Locking the Door Press Lock button once. Unlocking the Door Enter user code. Tip: You can press the Lock button before entering your user code to light up the keypad at night. 9 Re-key the lock (if needed) and install the battery cover A Re-key the lock (if needed). B Install the battery cover. a K b c K a IMPORTANT: Remove battery pack before re-keying. Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information. Reinstall battery pack. H b M 3 / 4 actual size V V (3x) Reference Guide SmartCode at a Glance Keypad SmartKey tool hole Exterior Interior (cover removed) Back panel Button "A" Button "B" Lock button Keyway Program button Status LED Switches Turnpiece System Alerts Alert Keypad flashes red 1 time with 1 beep* Reason Door jammed while attempting to lock. Keypad flashes red 3 times with 3 beeps* Keypad flashes red 10 times with 10 beeps* Lock beeps 2 times. Unsuccessful programming. One incorrect code entered. No user code programmed. Low battery. Keypad flashes red 3 times. Keypad flashes red 6 times with 6 beeps*. Programming timeout. Solution Manually re-lock door. If needed, reposition strike. Attempt programming procedure again. Re-enter code. Program at least one user code. Replace batteries. Attempt programming procedure again, making sure not to pause for more than 5 seconds. Keypad flashes red 15 times Three incorrect codes entered Re-enter code after 60 second keypad with 15 beeps* within one minute. lockout. *Beeping sound will only be heard if switch #3 is on. Switches and Status LED colors Switches On Off 1 2 3 4 Switch Function 1 Door lock status LED blinks every 6 seconds Lock automatically re-locks door 30 2 seconds after unlocking. Disabled if no codes are programmed. 3 Audio 4 Not used. Status LED Color Lock Status Blinking green Unlocked Blinking amber Locked Blinking red Low battery Solid red Door handing process did not work properly. See the online Programing and Troubleshooting Guide. Troubleshooting A complete Programming and Troubleshooting Guide is available on the SmartCode 910 page at www.kwikset.com. Deleting a user code In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three. Test the old user code to make sure it can no longer unlock the door. If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock. Factory Reset A factory reset will delete all codes associated with the lock, and it will remove it from your smart home system. 1 Remove battery pack. 2 Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Status LED 3 Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset. 4 Perform the door handing process again to teach the lock the orientation of the door, pair the lock with your smart home system, and add user codes to your lock. Network Information Removing the lock from the network Follow your smart home system's instructions to remove the lock from the network. When prompted by the system, press button A" on the lock interior once. Z-Wave System Notes This product is a security enabled Z-wave Plus product and must be used with a Security Enabled Z-Wave controller to be fully utilized. Z-Wave is a "Wireless mesh network," and results may vary based on building construction and communication path, with 35 feet+ being typical installed distance from smart home controller. It may be necessary to install additional Z-Wave beaming capable devices that can serve as repeaters to enhance the communication path between the lock and controller for a more robust Z-Wave network. To assure interoperability, each Z-Wave product must pass a stringent conformance test to assure that it meets the Z-Wave standard for complete compliance with all other devices and controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers that their products will reliably perform with any other Z-Wave device. And, regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products. Z-Wave Configuration and Association Parameters are available on the SmartCode 910 page at www.kwikset.com. Important Safeguards 1. Read all instructions in their entirety. 2. Familiarize yourself with all warning and caution statements. 3. Remind all family members of safety precautions. 4. Protect your user codes and mastercode. 5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system's settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder's hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional. 4 / 4 © 2016 Spectrum Brands, Inc.Acrobat Distiller 15.0 (Windows)