for ROBe models including: Robin Parfect 150 FWQ, Robin, Parfect 150 FWQ, 150 FWQ
26 mag 2022 — FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY. BEFORE POWERING OR INSTALLING YOUR ROBIN ParFect 150 ! Save it for future reference. This device ...
QR code for user manual
Version 2.1 1
ROBIN ParFect 150 ROBIN ParFect 150 FW
ROBIN ParFect 150Q ROBIN ParFect 150 FWQ
Table of contents
1. Safety instructions.......................................................................................................... 3 2. Fixture exterior view ...................................................................................................... 5 3. Installation....................................................................................................................... 6
3.1 Connection to the mains............................................................................................. 6 3.2 Installing barndoors and the gel frame........................................................................ 7 3.3 Installing the eggcrate................................................................................................. 8 3.4 Installing the diffuser 2°............................................................................................... 9 3.5 Rigging the fixture..................................................................................................... 10 3.6 DMX-512 connection................................................................................................. 12 3.7 Wireless DMX operation........................................................................................... 13 4. Control menu map......................................................................................................... 14 5. Control menu (Standard and Easy control mode)...................................................... 16 5.1 Addressing (DMXA)................................................................................................... 16 5.2 Fixture information (Info)........................................................................................... 17 5.3 Personality (Pers)...................................................................................................... 17 5.4 Manual Control (Manual)........................................................................................... 18 5.5 Test program (Test Prg)............................................................................................. 18 5.6 Stand-alone (St Alone).............................................................................................. 18 5.7 Special functions (Special)........................................................................................ 19 6. RDM................................................................................................................................ 21 7. Error and information messages................................................................................. 22 8. Technical Specifications............................................................................................... 22 9. Maintenance and cleaning............................................................................................ 24 9.1 Replacing the fuse.................................................................................................... 24 9.2 Disposing of the product........................................................................................... 25 10. Photometric diagrams................................................................................................ 26 10.1 ROBIN Parfect 150................................................................................................. 26 10.2 ROBIN Parfect 150 FW........................................................................................... 30 11. ChangeLog .................................................................................................................. 32
2
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR ROBIN ParFect 150 !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
The ParFect 150 was designed for indoor use and it is intended for professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the fixture. This fixture should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before cleaning, removing or installing any part of the fixture.
The power plug has to be accessible after installing the fixture. Do not overload wall outlets and extension cords as this canresult in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this fixture where the cord may be damaged by persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power cord from time to time.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to a mains socket outlet with a protective earthing connection.
Do not connect this fixture to a dimmer pack.
Warning! Risk group 2, RG-2: CAUTION. Do not stare at exposed lamp in operation. May be harmful to the eyes. Avoid looking directly into the light source LED light emission. Do not view the light output with optical instruments or any device that may conncentrate the beam. The light source contains blue LEDs.
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
3
Avoid brute force when installing or operating the fixture. This fixture was designed for indoor use only, do not expose this unit to rain or use near water. When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat, moisture or dust.
Do not block the lens array with any object when the fixture is under operation.
Openings in housing of the fixture should never be covered with cloth or other materials, and never must be blocked. This fixture should not be placed in a built-in installation unless proper ventilation is provided. Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened. Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
To avoid damage of an internal optical system of the fixture, never let the sunlight (or other light source) lights directly to the lens array, even when the fixture is not working
The fixture becomes hot during operation. Allow the fixture to cool approximately 15 minutes prior to manipulate with it. Operate the fixture only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the fixture. Most damages are the result of unprofessional operation! Please use the original packaging if the fixture is to be transported. Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons! If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc. Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use. Part 2: Immunity. The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given by this standard (e.g. transmitters in surrounding area) before installing the equipment. Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia equipment Emission Requirements according to class B.
Potential foggy front lens array does not influence function of the fixture and does not subject to complaint.
4
2. Fixture exterior view
1 - Mounting yoke 2 - Tilt locks 3 - Lenses array
4 - Safety wire securing accessory frame adaptor to the housing
5 - DMX OUT 6 - DMX IN 7 - Fuse holder 8 - Mains IN 9 - Mains OUT 10 - Display and control buttons 11 - Safety wire attachment point
5
3. Installation
Fixtures must be installed by a Qualified electrician in accordance with all national and local electrical and construction codes and regulation.
3.1 Connection to the mains
For protection from electric shock, the fixture must be earthed!
The ParFect 150 is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC power source from 100-240 Volts.
If you need to install a cord cap on the power cable to allow connection to power outlet, install a grounding-type (earthed) plug, following the plug manufacturer's instructions. If you have any doubts about proper installation, consult a qualified electrician.
Core (EU) Brown Light blue Yellow/Green
Core (US) Black White Green
Connection Plug Terminal Marking
Live
L
Neutral
N
Earth
This device falls under class one and must be earthed (grounded)!
The max. number of connected fixtures depends on AC mains power voltage:
CE:
ETL:
15 fixtures at power supply= 230V
9 fixtures at power supply= 230V
13 fixtures at power supply= 208V
8 fixtures at power supply= 208V
7 fixtures at power supply= 120V
4 fixtures at power supply= 120V
Actual number of fixtures may differ from values stated above as you have to take into account the length of
supply cables, circuit breaker etc. at projecting of the fixtures installation Do not overload the supply line and
connecting leads.
Wiring and connection work must be carried out by qualified staff!
.
6
3.2 Installing barndoors and the gel frame
Disconnect the fixture from mains before barndoors and the gel frame installation! DO NOT install the gel frame if the eggcrate has been installed on the fixture!
1. Unlock the spring lock (1) of the accessory frame adaptor (2) via pushing this spring lock as show red arrows on the picture. 2. Insert the gel frame (3) into the bottom slots of the accessory frame adaptor (2). 3. Insert the barndoors (4) into the top slots of the (2).
4. Secure both accessories by moving the spring lock (1) to locked position as shows the red arrow on the picture.
7
Note: the barndoors can be rotated to desired position and secured in this position via the securing screw (5).
3.3 Installing the eggcrate
Disconnect the fixture from mains before eggcrate installation! DO NOT insert the gel frame after installing the eggcrate on the fixture!
Screw the eggcrate (1) on the lens array module via the three screws (2).
8
3.4 Installing the diffuser 2° (Robin Parfect 150/150Q only)
Disconnect the fixture from mains before installing the diffuser.
1. Unscrew three screws (1) from fixture head and remove the plastic lens (2). 2. Place the diffuser 2° (3) to the fixture head, glossy side towards LEDs (correctly aim apertures (4) for screws). 3. Screw the diffuser 2° (3) back to the head by means of the three screws (1)
Warning Installation of the Diffuser 2° is one-time matter as the screws (1) are screwed into
the plastic. You cannot install and uninstall the Diffuser 2° several times.
9
3.5 Rigging the fixture
A structure intended for installation of the fixture (s) must safely hold weight of the fixture(s) placed on it. The structure has to be certificated to the purpose.
The fixture (fixtures) must be installed in accordance with national and local electrical and construction codes and regulation.
For overhead installation, the fixture must be always secured with a safety wire.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
Allow the fixture to cool for ten minutes before handling.
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but use a help of professional companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do not install the fixture!
The fixture has to be installed out of the reach of public.
The fixture must never be fixed swinging freely in the room.
When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) in a distance of min. 0.4 m.
.
CAUTION!
Use an appropriate clamp to rig the fixture on the truss.
Make sure that the device is fixed properly! Ensure that the
structure (truss) to which you are attaching the fixtures is secure.
The fixture can be placed by means of the unfolded mounting yoke on the stage floor or rigged on a truss (with folded mounting yoke) without altering its operation characteristics.
10
For securing the fixture to the truss, install a safety wire which can hold at least 10 times the weight of the fixture. Use only the safety wire with a snap hook with screw lock gate. Fasten the safety cable in the attachment point and around the truss as shown on the picture below.
1-Clamp 2-Truss 3-Safety wire 4-Attachment point 5-Folded mounting yoke
When installing fixtures side-by-side, avoid illuminating one fixture with another!
11
3.6 DMX-512 connection
The fixture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair cable designed for RS-485 and 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
DMX output XLR socket:
DMX input XLRplug:
1 - Shield 2 - Signal (-) 3 - Signal (+) 4 - Used for wireless DMX 5 - Used for wireless DMX
1 - Shield 2 - Signal (-) 3 - Signal (+) 4 - Used for wireless DMX 5 - Used for wireless DMX
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain: Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected. Up to 32 fixtures can be interconnected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal () and Signal (+) into a 5-pin XLR-plug and plug it in the DMX-output of the last fixture.
12
3.7 Wireless DMX operation
The external ROBE Wireless CRMX Dongle allows receiving wireless DMX. This device is equipped with the Lumen Radio CRMX module and antenna for receiving DMX signal. CRMX module operates on the 2.4 GHz band.
ROBE Wireless CRMX Dongle
1 - 5-pin XLR (female) 2 - Locating pin 3 - Lock
Push the 5-pin XLR plug (1) into 5-pin XLR sockit (4) and at the same time locating pin (2) into the opening (5) in the fixture. In this way the wireless DMX module is connected with the fixture. NOTE: when you disconnecting the DMX wireless module from the fixture, press and hold lock (5) during taking the wireless module out. To link the fixture with DMX transmitter. The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter . After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item "Stat" (Special -->Vireless -->Stat). To unlink the fixture from DMX transmitter. The fixture can be unlinked from receiver via the menu item " Unlink" (Special-->Vireless -->Unlink.).
13
4. Control menu map
Default settings=Bold print
Level 1
Level 2
Level 3
DMXA
Set DMXA DMX Pres
001-512 Mode 1 Mode 2
Level 4
Info
POn Time
Total
Reset
DMX In
Powr
0-255
:
Dim F
0-255
Hea Temp
Current
Highest
High Res
Sw Ver
IC-1
IC-2
Pers
DMX Pres Display
Mic Sens Fans Col Mix White P Dimmer C LED Freq LED Fadj Temp Uni I Ef Pos
Defaults
Mode 1 Mode 2 Turn On/Off T Contrast Backlight 0...10...19 Auto, High,Quiet RGBW, CMY On, Off Square, Linear Stand High -06,-05..00..05, 06 °C, °F Powr : Dimm F Store
On, Off 0-100% 0-100%
Manual
Manual C
Powr : Dim F
0-255 0-255
Test Prg
Sta Alone
Music T Auto Run
Pr Play
On, Off Off Test Prog 1 : Prog 3 Test Prg Prog 1 :
Level 5
14
Level 6
Level 7
Level 1
Level 2 Pr Edit
Level 3 Prog 3 Prog 1 Prog 2 Prog 3
Special
RDM Low RDM Hight Wireless
Adjust
Stat Unlink DMX Val
Clalib
Sw Upd
On, Off
Level 4
Step 1 : Step 40
Level 5
Powr : F.Tim S.Tim COPY Prg En
Powr : Dim F Cal Mech Cal Col
Cla Load
0-255
0-255 Zoom C Store Red C Gre C Blu C Whi C Store
Level 6
Level 7
0-25.5 0-25.5
1-40
0-255
0-255 0-255 0-255 0-255
15
5. Control menu (Standard and Easy control mode)
The ParFect 150 is equipped with 2-row LCD display which allows to set the fixture´s behaviour according to your needs, obtain information on its operation, test its various parts and lastly program it, if it has to be used in a stand-alone mode. Control panel
The four control buttons have the following functions: Standard control mode (default setting) [ESCAPE] button used to leave the menu without saving changes. [NEXT] , [PREV] buttons for moving between menu items and for value adjusting. [ENTER] button used to enter the selected menu (menu item) and to confirm adjusted value. After switching the fixture on, the display shows current DMX address.
Easy control mode [INTENSITY] buttons used to set light intensity (dimmer). [COLOR] buttons used to set colour After switching the fixture on, the display shows adjusted dimmer intensity and colour before switching the Parfect 150 off.
When the fixture is switched off, both adjusted color and light intensity are saved into memory to use them after switching the fixture on. Note: DMX control in this mode is disabled. Switching the fixture to Easy control mode When the current DMX address is displayed:
press the [NEXT] and [PREV] buttons at the same time until the screen for the Easy control mode appears.
For switching to the Standard control mode, press the [NEXT] and [PREV] buttons at the same time until the screen for the Standard control mode appears.
The following menu items are accessible in the Standard control mode only.
5.1 Addressing (DMXA)
Set DMXA- Use this menu item to set the DMX start address of the fixture, which is defined as the first channel from which the ParFect 150 will respond to the controller. If you set, for example, the address 31, the ParFect 150 will use channels 31 - 48 for control (if Mode 1 is selected).
16
Please, be sure that you do not have any overlapping channels in order to control each ParFect 150 correctly and independently from any other fixture on the DMX data link. If there is no data received at the DMX input, the display will start to flash "0001" with actually stored DMX address.
DMX Pres - DMX preset. Use the menu to select desired channel mode. Mode 1 - 17 control channels (default) Mode 2 - 11 control channels
5.2 Fixture information (Info)
POn Time - Power on time. Select this menu to read the number of fixture operation hours. Total - The item shows the total number of the operation hours since the ParFect 150 has been fabricated. Reset - The item shows the number of the operation hours that the ParFect 150 has been powered on since the counter was last reset. In order to reset this counter to 0, press and hold both [NEXT] and [PREV] buttons and the [Enter] button at the same time.
DMX In - DMX readout. The menu is used to read DMX values of each channel received by the fixture.
Hea. Temp - Temperature. The menu shows temperature of the LED module. Current - A current temperature of the LED module. Highest - A maximum temperature of the the LED module since the fixture has been fabricated. High Res - A maximum temperature of the the LED module since the counter was last reset. In order to reset this counter, press and hold both [NEXT] and [PREV] buttons and the [Enter] button at the same time.
Sw Ver - Software versions. Select this item to read the software version of the fixture modules. IC-1 - A display processor. IC-2 - A LED control processor.
5.3 Personality (Pers)
DMX Pres - DMX preset. Use the menu to select desired channel mode. Mode 1 - 17 control channels (default) Mode 2 - 11 control channels
Display - Display adjusting. This menu allows you to adjust the display behaviour. Turn - This function rotates menu 180 degrees from current orientation. Note: Pressing and holding the Escape button also rotates menu. On/Off T - This function allows you to keep the display permanent on or turn it off two minutes after last pressing any button on the control panel. Contrast- Use this function to adjust contrast of the display (0-100%). Backlight- Use this function to adjust backlight of the display (0-100%).
Col. Mix. - Colour mixing mode. This item allows switching into RGBW or CMY mode. In the CMY mode, the white(8bit) and white (16) bit channels are not active.
White P - White Point 8000K. If the function is on, the CTC channel allows to set desired white in range of 8000K-2700K (0 DMX=8000K,64 DMX=5600K, 128 DMX=4200K, 192 DMX=3200K, 255 DMX=2700K). Necessary condition is , that RGBW channels have to be full or set at the same DMX values, e.g. 255. If this function is off, the range of whites is not uniform and may be different for each fixture.
Mic Sens - Microfon sensitivity. Enter the menu if you want to adjust the microphone sensitivity (0-min., 19max.).
Fan - Fan mode. Use the menu to set the fixture fan to the max. power ("High") ,auto-control mode ("Auto") and quiet mode ("Quiet"). In the quiet mode is a speed of zoom reduced.
17
LED Freq - LEDs frequency setup. The function allows you to set the PWM (Pulse Width Modulation) output frequency of LEDs to Standard or High.
Stand - a standard frequency (300Hz), default setting. High - a high frequency (600Hz)
LED Fadj - LEDs frequency fine adjustment. The function allows you to change the selected PWM output frequency of LEDs in 6 levels up and down around the selected frequency in the menu "LED Freq".
-06...-01 - Frequence levels 1-6 under selected frequency. 00 - Selected frequency (Standard or High) 01...06 - Frequence levels 1-6 above selected frequency.
Temp Uni - Temperature unit. Use the menu item to change temperature unit from °C to °F.
I Ef Pos - Init effect positions. Use the menu to set all effects to the desired positions at which they will stay after switching the fixture on without DMX signal connected.
Defaults - The menu item allows to set all fixture parameters to the default (factory) values.
5.4 Manual Control (Manual)
Use the menu to control all fixture channels by means of the control panel.
5.5 Test program (Test Prg)
Use this menu to to run a special demo-test sequences without an external controller, which will show you some possibilities of using the ParFect 150.
5.6 Stand-alone (St Alone)
The ParFect 150 offers three user-editable programs (Prog 1-Prog 3), each up to 40 steps. T
Music T - Music trigger. Select this function to enable the sound control of the running program via the built-in microphone.
Auto Run - Presetting playback. This function allows you to select the program which will be played in the stand-alone mode after switching the fixture on. Selected program will be played continuously in a loop.
Off - The option disables ,,Auto Run" function. Test, Prog 1, Prog 2, Prog 3 - Selected program will start running after switching the fixture on.
Pr Play - Playing program. Select this menu to run a desired program in a loop (Test Prg, Prog 1-Prog 3). Select the program you wish to run and press the [ENTER]. The selected program will start running. By Pressing the [ENTER] again, the program pauses running.
Pr Edit - Editing program. Select this menu to edit or create three editable programs (Prog 1-Prog 3). Each
program step has a step time - during which effects last in the current step and a fade time- during which effects
move to new positions.
To edit program.
1. Press [NEXT] or [PREV] to select the menu "Pr Edit" and press [ENTER].
2. Press [NEXT] or [PREV] to select the desired program and press [ENTER] button.
3. Press [NEXT] or [PREV] to select the desired program step and press [ENTER] button.
4. Press [NEXT] or [PREV] to select the desired item and press [ENTER] button. Now you can edit by [NEXT]
or [PREV] buttons the DMX value (0-255) for selected item:
Prg En.
a total number of the program steps (value 1-40). This value you should be set before
starting of programming (e.g. if you want to create program with the 10 steps,
set Prg En=10).
Powr
power/special functions
Virt C
a virtual colour wheel
Red
a red colour coarse
Red F
a red colour fine
18
Green
a green colour coarse
Green F
a green colour fine
Blue
a blue colour coarse
Blue F
a blue colour fine
White
a white colour
White F
a white colour fine
CTC
a colour temperature correction
C Mix C
a colour mix control
Zoom
a zoom function
Zoom F
a zoom function fine
Stro
a strobe/shutter function
Dimm
a dimmer function coarse
Dim F
a dimmer function fine
F.Tim a fade time (0-25.5 sec)
S.TiM a step time (0-25.5 sec)
COPY copying the current prog. step to
the next prog. step
5. Press [ENTER] button to confirm adjusted value .
6. Press [ESCAPE] button, select next prog. step, press [ENTER] button and repeat steps 4 - 5).
5.7 Special functions (Special)
RDM Low - This menu item shows the first part of the RDM identification code.
RDM High - This menu item shows the second part of the RDM identification code.
Wireless - Wireless DMX information. The menu allows to read some information about Wireless DMX operation
Stat - Wireless status. Use the menu to read wireless DMX status. Unlink - use this item to unlink fixture from wireless DMX.
Adjust - Adjustment. The menu allows the fine adjustment of effects. DMX Val- DMX values. Use the menu to set DMX values of fixture´s channels. Calib - calibration of white colour. Cal Mech - Use this menu to calibrate a zoom position. Cal Col - Use this menu to set white colour 5600K.
Calibration of the zoom position via the control board 1. Disconnect DMX controller from the fixture and enter the "Cal Mech" menu. 2. Use the [PREV] and [NEXT] to find "Zoom C" and press [ENTER]. 3. Set desired value and confirm it by pressing [ENTER]. 4. After calibration, find item "Store" and press [ENTER]. to save all adjusted values and reset the fixture.
Calibration of the white 5600K via the control board 1. Disconnect DMX controller from the fixture , set the shutter, dimmer and RGBW channels at 255 DMX, zoom at 128 DMX and the CTC channel at DMX=64 (white 5600K). Aim the light beam on the lux meter (e.g. Minolta CL-500 A Chroma meter) which is placed cca 5m from the fixture. 2. Set the menu items colour mixing mode "Colour Mix" to RGBW and white point 8000K "White P" to On (Pers-> Col Mix -> RGBW, Pers-> White P -> On). 3. Enter the menu "Cal Col". 4. By means of the items "Red C, Gre C, Blu C and Whi C" adjust the 5600K colour temperature
as exactly as possible (u´v´= 0). 5. After adjusting 5600K colour temperature, select item Store and press the [ENTER] button to save all
adjusted values . Note: you can also use a DMX controler for both calibrations stated above, calibration protocol is the following:
Effect Fine adjustment of zoom position Fine adjustment of red LEDs saturation Fine adjustment of green LEDs saturation Fine adjustment of blue LEDs saturation Fine adjustment of white LEDs saturation
Mode 1 channel 18 channel 19 channel 20 channel 21 channel 22
19
Mode 2 channel 12 channel 13 channel 14 channel 15 channel 16
Cal Load - Loads default (factory) calibration.
Sw Upd - Software update. The menu item allows you to update software in the fixture. The following items are required in order to update software: - PC running Windows or Linux or macOS - DSU file - Robe Universal Interface or Robe Universal interface WTX or Flash cable RS232/DMX P/N13050624)
After the software updating the fixture will be set to default (factory) values.
To update software in the fixture: 1. DSU file is available from Robe web site at WWW.robe.cz.
File with extension zip is intended for Windows (used and tested from XP to W10 on 32/64bit systems). File with extension tbz is intended for Linux (used and tested on Debian and Ubuntu 32/64bit). File with extension dmg is intended for macOS (used and tested on OSX up to Sierra) XQuartz required, install it from https://www.xquartz.org/ Save the download file to a folder on your computer. In case that you use windows, extract files in the zip file (e.g. DSU_Parfect150_18050253.zip) 2. Disconnect the fixture from DMX controller. 3. If you use the flash cable RS232/DMX, connect a serial port of your computer with DMX input of the fixture by means of the cable. If you use the Robe Universal Interface, connect a USB port of your computer with the Robe Universal Interface by means of the USB cable and DMX input of the fixture with the DMX output of the Robe Universal Interface via a DMX cable. 4. Switch the fixture to the update mode (Special --> SW Upd). Note: If you do not want to continue in the software update, you have to switch off and on the fixture to escape from the updating mode. We recommend to cancel all running programs on your computer before starting the software update. 5. Double-click the software uploader file (e.g. DSU_Parfect150_18050253.exe) in the extracted files. The Software Uploader program will start running.
6. Select correct "COM " number if you use a Flash cable RS232/DMX or select "Robe Universal Interface 1 " if you use the Robe Universal Interface/Robe Universal Interface WTX and then click on the "Connect" button.
7. If the connection is OK, click the "Start Uploading" button to start software uploading. It will take several minutes to perform software update. If the option "Incremental Update" is not checked, all processors will be updated (including processors with the same software version). If you wish to update only processors with new version of software, check the "Incremental Update box". Avoid interrupting the process. Update status is being displayed in the "Info Box" window. When the update is finished, the line with the text "Fixture is successfully updated" will appear in this window.
20
In case upload process is interrupted (e.g. power loss), the fixture stays in "Updating mode" and you will have to repeat the software update again.
Another way, how to update software in the fixtures (especially large installation of fixtures) is to use the ROBE Uploader. It is a software for automatized software update of Robe fixtures. It takes advantage of RDM support in the unit. For more information please see https://www.robe.cz/robe-uploader/.
6. RDM
This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non-RDM equipment. By using a special ,,Start Code," and by complying with the timing specifications for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific moving lights. RDM allows explicit commands to be sent to a device and responses to be received from it. The list of commands for the ParFect 150 is the following.
Parameter ID
Discovery command SET command
GET command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
DEVICE_LABEL
*
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_INVERT
*
*
DISPLAY_LEVEL
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
PARAMETER_DESCRIPTION
*
ROBE_DMX_INPUT
*
*
ROBE_WIRELESS_UNLINK
*
RDM model ID for the ROBIN Parfect 150 is 0x00f5.
21
7. Error and information messages
Short Err The message informs you that short circuit has occured on the LED PCB.
8. Technical Specifications
Electrical
Power supply:.........................electronic auto-ranging Input voltage range:............... 100-240V, 50-60Hz Fuse:.......................................T 3.15A
Max. power consumption .....220W (I=1A, power factor=0.96 at 230V) Mains input: CE - max. 16A
ETL - max. 10A Mains output: CE - max. 15A
ETL - max. 9A
Optic
Light source: 7 x 30W RGBW multichip LEDs Min LED life expectancy: 20.000 hours RGBW/CMY colour mixing Variable CTO 2700-8000K CRI: 75 (white 8000K), 70 (white 5600K), 64 (white 4200K), 43 (white 3200K), 33 (white 2700K) Halogen lamp effect at whites 2700K and 3200K
Virtual colour wheel 66 preset colours Rainbow effect with variable speed
Zoom range Parfect 150: 3.8°-60° Parfect 150FW: 3.8°-60°
Strobe Dimmer
Strobe effect with variable speed (0.3 - 20Hz) Random strobe pulse-effect with variable speed Opening/closing pulse effect with variable speed
Smooth dimmer from 0 - 100 %
Control
2-row LCD display & 4 buttons Readout fixture usage, receiving DMX values, temperatures, etc Built-in analyzer for easy fault finding, error messages Built-in demo sequences Quiet fan cooling Stand-alone operation 3 user editable programs, each up to 40 steps Supported protocols: USITT DMX 512, RDM, Support of RDM (Remote Device Management) 2 DMX modes (17, 11 control channels) 2 control modes (Standard and Easy)
External Wireless DMX/RDM module (option) Compliance with USITT DMX-512 (1986 & 1990) and 512-A Full DMX fidelity and frame integrity Auto sensing of DMX frame rate and frame size 22
<5ms DMX latency Operational frequency range of 2402-2480 MHz Producer: LumenRadio
Connection
DMX data in/out: Locking 5-pin XLR AC power input: Chassis connector Neutrik PowerCon, A-type, NAC3MPA AC power output: Chassis connector Neutrik PowerCon, B-type, NAC3MPB Note: mains cable is optional accessories
Rigging
Mounting horizontally or vertically via mounting yoke (305° tilt range)
Temperatures Maximum ambient temperature : 40° C Maximum surface temperature : 80° C (at LEDs heat sink)
Distances
Min. distance from flammable surfaces: 0.4 m Min. distance of illuminated objects: 0.8 m
Total heat dissipation 562 BTU/h (calculated)
Weight 5 kg
Dimensions (mm)
ROBE Wireless CRMX Dongle for compact ROBIN fixtures 23
Included items ROBIN Parfect 150:
1 x ROBIN Parfect 150 1 x Accessory frame adaptor for Parfect 150 (P/N 99015324)
(installed on the fixture) 1 x User manual
ROBIN Parfect 150 FW: 1 x ROBIN Parfect 150 FW 1 x Accessory frame adaptor for Parfect 150 (P/N 99015324) (installed on the fixture) 1 x User manual
Optional accessories (P/N 10980127) ROBE Wireless CRMX Dongle for compact ROBIN fixtures (P/N 10980346) EggCrate for Robin LEDBeam 150/Parfect 150 (P/N 10980445) EggCrate for Robin LEDBeam 150, ParFect 150 white (P/N 10980348) HALO Frame adaptor for Robin ParFect 150 (P/N 10980349) Barndoor for Robin ParFect 150 black (P/N 10980415) Barndoor for Robin ParFect 150 white (P/N 10980372) Gel Frame for Parfect 150 (P/N 10980373) Diffusion filter 2° for Parfect 150 (for installation to gel frame) (P/N 10980423) Diffusion filter 2° for Parfect 150 (for one-time installation under lenses) (P/N1305 1731) Mains Cable PowerCon In/open ended, 2m (P/N 1305 1724) Mains Cable PowerCon In/Schuko, 2m (P/N 1305 1725) Mains Cable PowerCon In/CEE 16A, 2m (P/N 1305 1726) Mains Cable PowerCon In/US, 2m (P/N 1305 1727) Daisy Chain PowerCon In/Out, EU, 2m (P/N 1305 1728 ) Daisy Chain PowerCon In/Out, US, 2m (P/N 17030386) Doughty Trigger Clamp (P/N 99011963) Safety wire 35 kg
9. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture`s light output will be significantly reduced. Regular cleaning will not only ensure the maximum light output, but will also allow the fixture to function reliably throughout its life. A soft lint-free cloth moistened with any weak detergent solution is recommended for cleaning fixture´s covers, under no circumstances should alcohol or solvents be used!
DANGER ! Disconnect from the mains before starting any
maintenance and cleaning work
The interior of the fixture should be cleaned at least annually using a vacuum cleaner or compressed air. The cooling fan should be cleaned at least once a year.
Important! Never use alcohols (ethanol, methanol, isopropyl alcohol), acetone and another aggressive solvents for cleaning the LED lens array.
Recommended steps for cleaning the LED lens array: 1. Use low-pressure compressed air to remove coarse dust from lenses. 2. Use distilled water with weak detergent solution and lint-free small cloth for further cleaning of lenses. 3. Use an antistatic, alcohol-free screen cleaner (we recommend the Lyreco Screen Cleaner) and polish lenses
until they are dry. 4. Check the lenses are dry before reapplying power.
Note: potential foggy front lens array does not influence function of the fixture and does not subject to complaint
Checking plastic parts of the fixture. The plastic parts of the fixture should be checked for damages and beginning cracks at least every two months. If hint of a crack is found on some plastic part, do not use the fixture until the damaged part will be replaced.
24
Cracks or another damages of the plastic parts can be caused by the fixture transportation or manipulation and also ageing process may influence plastic materials. This checking is necessary for both fixed installations and preparing fixtures for renting. Any free moving parts inside of the fixture, cracked plastic or any plastic part not sitting properly in place need to be immediately replaced. More complicated maintenance and service operations are only to be carried out by authorized distributors.
9.1 Replacing the fuse
Replace the fuse by a fuse of the same type and rating only.
Before replacing the fuse, unplug mains lead!
1) Remove the fuse holder on the rear panel of the base with a fitting screwdriver from the housing (anti-clockwise). 2) Remove the old fuse from the fuse holder. 3) Install the new fuse in the fuse holder (only the same type and rating). 4) Replace the fuseholder in the housing and fix it.
9.2 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local regulations and codes.
25
10. Photometric diagrams 10.1 ROBIN Parfect 150/Parfect 150Q
26
27
28
29
10.2 ROBIN Parfect 150 FW/Parfect 150 FWQ
30
Copyright © 2017-2022 Robe Lighting - All rights reserved Specifications are subject to change without notice. May 26, 2022 Made in ROBE Lighting s.r.o., Palackého 416, 757 01 Valasské Meziící, Czech Republic
31
11. ChangeLog
This section summarizes all types of changes in the user manual.
Version of the Date of issue manual
Description of changes
1.1
14/05/2017
EggCrate installation added, DMX protocol ver.1.1
1.2
07/06/2017
Quiet mode for fan in menu Personality, DMX protocol ver. 1.2
1.3
30/10/2017
Accessory frame safety wire added
1.4
16/01/2018
Optional accessories changed
1.5
27/03/2018
Added installation of 2° Diffuser
1.6
29/07/2019
Checking of plastic parts added to chapter Maintenance.
1.7
12/11/2019
Description of lenses cleaning added
1.8
16/10/2020
Added information about foggy lens array
1.9
31/03/2021
DMX protocol ver. 1.3
2.0
12/11/2021
FWQ version added
2.1
21/02/2022
DMX protocol ver. 1.4 (Q-version added)
32
DMX protocol
Robin Parfect 150/Parfect 150 FW/Parfect 150Q/Parfect 150 FWQ - DMX protocol
Version: 1.4 Mode 1-Standard 16-bit, Mode 2 -Reduced 8-bit
Mode/channel DMX
1
2
Value
Function
Type of control
1
1
Power/Special functions
0 -19
Reserved (0=default) To activate following functions, stop in DMX value for at least 3 s and shutter must be closed at least 3 sec. (,,Shutter,Strobe" channel 20/15 must be at range: 0-31 DMX). Corresponding menu items are temporarily overriden.
20-24 Display ON
step
25-29 Display OFF
step
30-34 RGBW colour mixing mode
step
35-39 CMY colour mixing mode
step
40-59 Reserved
60 - 64 Dimmer curve - square law
step
65 - 69 Dimmer curve - linear
step
70 - 74 Fan mode: Auto
step
75 - 79 Fan mode: High
step
80-84 White point 8000K ON
step
85-89 White point 8000K OFF
step
90-94 Fan mode: Quiet
step
95 -129 Reserved
To activate following functions, stop in DMX value for at least 3 seconds. Corresponding menu items are temporarily overriden.
130 - 149 Reserved
150 - 159 Zoom reset
step
160 - 169 Reserved
Tungsten effect simulution for whites 2700K and 3200K
170-171 Tungsten effect simulation (750W) On
step
172-173 Tungsten effect simulation (1000W) On
step
174-175 Tungsten effect simulation (1200W) On
step
176-177 Tungsten effect simulation (2000W) On
step
178-179 Tungsten effect simulation (2500W) On
step
180-181 Tungsten effect simulation Off
step
182-184 Reserved
185 PWM output frequency of LEDS: Standard (300Hz)**
step
186 PWM output frequency of LEDS: High (600Hz)**
step
** You can adjust selected frequency in 6 steps Up or Down around selected
frequency - see table below . Default value of PWM frequency set in the fixture is
Standard.
187 LED Frequency (step -6)
step
188 LED Frequency (step -5)
step
189 LED Frequency (step -4)
step
190 LED Frequency (step -3)
step
191 LED Frequency (step -2)
step
192 LED Frequency (step -1)
step
193 LED Frequency (Standard or High)
step
194 LED Frequency (step +1)
step
195 LED Frequency (step +2)
step
196 LED Frequency (step +3)
step
Page 1
DMX protocol
Mode/channel
1
2
2
2
DMX Value
Function
197 LED Frequency (step +4)
198 LED Frequency (step +5)
199 LED Frequency (step +6)
200-255 Reserved
Virtual colour wheel
0 No function (0=default)
1-2 Filter 4 (Medium Bastard Amber)
3-4 Filter 25 (Sunset Red)
5-6 Filter 19 (Fire)
7-8 Filter 26 (Bright Red)
9-10 Filter 58 (Lavender)
11-12 Filter 68 (Sky Blue)
13-14 Filter 36 (Medium Pink)
15-16 Filter 89 (Moss Green)
17-18 Filter 88 (Lime Green)
19-20 Filter 90 (Dark Yellow Green)
21-22 Filter 49 (Medium Purple)
23-24 Filter 52 (Light Lavender)
25-26 Filter 102 (Light Amber)
27-28 Filter 103 (Straw)
29-30 Filter 140 (Summer Blue)
31-32 Filter 124 (Dark Green)
33-34 Filter 106 (Primary Red)
35-36 Filter 111 (Dark Pink)
37-38 Filter 115 (Peacock Blue)
39-40 Filter 126 (Mauve)
41-42 Filter 117 (Steel Blue)
43-44 Filter 118 (Light Blue)
45-46 Filter 122 (Fern Green)
47-48 Filter 182 (Light Red)
49-50 Filter 121 (Filter Green)
51-52 Filter 128 (Bright Pink)
53-54 Filter 131 (Marine Blue)
55-56 Filter 132 (Medium Blue)
57-58 Filter 134 (Golden Amber)
59-60 Filter 135 (Deep Golden Amber)
61-62 Filter 136 (Pale Lavender)
63-64 Filter 137 (Special Lavender)
65-66 Filter 138 (Pale Green)
67-68 Filter 798 (Chrysalis Pink)
69-70 Filter 141 (Bright Blue)
71-72 Filter 147 (Apricot)
73-74 Filter 148 (Bright Rose)
75-76 Filter 152 (Pale Gold)
77-78 Filter 154 (Pale Rose)
79-80 Filter 157 (Pink)
81-82 Filter 143 (Pale Navy Blue)
83-84 Filter 162 (Bastard Amber)
85-86 Filter 164 (Flame Red)
Page 2
Type of control
step step step
step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step step
DMX protocol
Mode/channel
1
2
3
3
4
*
5
4
6
*
7
5
8
*
9
6
10
*
11
7
DMX Value
Function
87-88 Filter 165 (Daylight Blue)
89-90 Filter 169 (Lilac Tint)
91-92 Filter 170 (Deep Lavender)
93-94 Filter 172 (Lagoon Blue)
95-96 Filter 194 (Surprise Pink)
97-98 Filter 180 (Dark Lavender)
99-100 Filter 181 (Congo Blue)
101-102 Filter 197 (Alice Blue)
103-104 Filter 201 (Full C.T. Blue)
105-106 Filter 202 (Half C.T. Blue)
107-108 Filter 203 (Quarter C.T. Blue)
109-110 Filter 204 (Full C.T. Orange)
111-112 Filter 219 (Fluorescent Green)
113-114 Filter 206 (Quarter C.T. Orange)
115-116 Filter 247 (Filter Minus Green)
117-118 Filter 248 (Half Minus Green)
119-120 Filter 281 (Three Quarter C.T. Blue)
121-122 Filter 285 (Three Quarter C.T. Orange)
123-124 Filter 352 (Glacier Blue)
125-126 Filter 353 (Lighter Blue)
127-128 Filter 507 (Madge)
129-130 Filter 778 (Millennium Gold)
131-132 Filter 793 (Vanity Fair)
133-235 Raw DMX
236-245 Rainbow effect (with fade time) from slow-> fast
246-255 Rainbow effect (without fade time) from slow-> fast
Red/Cyan (8 bit)*
0 - 255 Colour saturation control - coarse 0-100% (255=default)
Red/Cyan (16bit)*
0 - 255 Colour saturation control - fine (255=default)
Green/Magenta (8 bit) *
0 - 255 Colour saturation control - coarse 0-100% (255=default)
Green/Magenta (16bit) *
0 - 255 Colour saturation control - fine (255=default)
Blue/Yellow (8 bit) *
0 - 255 Colour saturation control - coarse 0-100% (255=default)
Blue/ Yellow (16bit) *
0 - 255 Colour saturation control - fine (255=default)
White (8 bit)
If RGBW mode is selected:
0-255 Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
0 - 255 No function
White (16 bit)
0 - 255 Colour saturation control - fine (255=default)
CTC
If function "White Point 8000K" is ON
0-255 Col. temperature correction from 8000K to 2700K -for whites only
(0=8000K, 64=5600K, 128=4200K, 192=3200K, 255=2700K)
Page 3
Type of control
step step step step step step step step step step step step step step step step step step step step step step step proportional proportional proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
Mode/channel
1
2
DMX protocol
DMX Value
Function
To get colour temperatures stated above, RGBW channels have to be set at the same value e.g. 255DMX (0=default) (To activate Tungsten effect at 2700K and 3200K , set DMX value at "Power/Special functions" channel)
Type of control
If function "White Point 8000K" is OFF
0-255 Colour temperature correction for from cool white to 2700K
12
8
Colour Mix control
Defines relation between colour channels
"Virtual" = Virtual Colours (Virtual Colour Wheel)
"Colour mix" = Colour channels (RGBW/CMY)
0-9 Virtual colors ("Virtual" has priority)
10-19 Maximum mode (highest values have priority)
20-29 Minimum mode (lowest values have priority)
30-39 Multiply mode (multiply Virtual and Colour Mix)
40-49 Addition mode (Virtual + Colour mix) (45=default)
50-59 Subtraction mode (Virtual Colour mix)
60-69 Inverted Subtraction mode (Colour mix Virtual)
70-128 Reserved
129 Virtual colors (virtual has priority)
130-254 Crossfade (crossfade between Virtual and Colour mix)
255 Colour channels ("Colour mix" has priority)
13
9
Zoom
0-255 Zoom from max. to min.beam angle (128=default)
14
*
Zoom - fine
0-255 Fine zooming (0=default)
15 10
Shutter/ strobe
0 - 31 Shutter closed
32 - 63 Shutter open (32=default)
64 - 95 Strobe-effect from slow to fast
96 - 127 Shutter open
128 - 143 Opening pulse in sequences from slow to fast
144 - 159 Closing pulse in sequences from fast to slow
160 - 191 Shutter open
192 - 223 Random strobe-effect from slow to fast
224 - 255 Shutter open
16 11
Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (0=default)
17
*
Dimmer intensity - fine (16 bit)
0 - 255 Fine dimming (0=default)
proportional
step step step step step step step
step proportional
step
proportional
proportional
step step proportional step proportional proportional step proportional step
proportional
proportional
*Select RGB or CMY mixing mode on channel "Power/Special functions" .
Copyright © 2017-2022 Robe Lighting s.r.o. - All rights reserved All Specifications subject to change without notice
Page 4
Colours on Virtual Colour Wheel
Colour name
Red (DMX)
Green (DMX)
Filter 4 (Medium Bastard Amber)
255
118
Filter 25 (Sunset Red)
255
47
Filter 19 (Fire)
255
13
Filter 26 (Bright Red)
255
0
Filter 58 (Lavender)
117
0
Filter 68 (Sky Blue)
31
219
Filter 36 (Medium Pink)
255
74
Filter 89 (Moss Green)
69
245
Filter 88 (Lime Green)
187
226
Filter 90 (Dark Yellow Green)
2
255
Filter 49 (Medium Purple)
255
0
Filter 52 (Light Lavender)
232
88
Filter 102 (Light Amber)
223
164
Filter 103 (Straw)
191
144
Filter 140 (Summer Blue)
0
149
Filter 124 (Dark Green)
29
255
Filter 106 (Primary Red)
242
1
Filter 111 (Dark Pink)
255
67
Filter 115 (Peacock Blue)
0
255
Filter 126 (Mauve)
255
0
Filter 117 (Steel Blue)
179
255
Filter 118 (Light Blue)
0
255
Filter 122 (Fern Green)
98
255
Filter 182 (Light Red)
255
16
Filter 121 (Filter Green)
165
255
Filter 128 (Bright Pink)
255
0
Filter 131 (Marine Blue)
73
245
Filter 132 (Medium Blue)
0
230
Filter 134 (Golden Amber)
166
83
Filter 135 (Deep Golden Amber)
255
50
Filter 136 (Pale Lavender)
140
101
Filter 137 (Special Lavender)
110
60
Filter 138 (Pale Green)
241
255
Filter 798 (Chrysalis Pink)
49
0
Filter 141 (Bright Blue)
0
225
Filter 147 (Apricot)
190
107
Filter 148 (Bright Rose)
255
3
Filter 152 (Pale Gold)
179
119
Filter 154 (Pale Rose)
214
118
Filter 157 (Pink)
255
56
Filter 143 (Pale Navy Blue)
0
193
Filter 162 (Bastard Amber)
211
153
Filter 164 (Flame Red)
255
27
Filter 165 (Daylight Blue)
23
236
Filter 169 (Lilac Tint)
185
123
Filter 170 (Deep Lavender)
235
123
Filter 172 (Lagoon Blue)
0
255
Blue (DMX)
0 0 0 0 97 105 8 0 0 0 27 6 0 0 3 0 1 11 29 39 14 76 0 2 0 13 27 120 0 0 25 45 4 98 62 0 0 0 0 5 67 6 0 93 0 41 63
White (DMX)
109 3 0 0
155 6
24 3 0 0 0
166 0
28 220
12 0
49 43
0 197
30 4 0 0
32 30
0 0 0 40 102 48 26 5 15 37 39 48 43 148 36 4 81 109 37 5
1
Colour name
Filter 194 (Surprise Pink) Filter 180 (Dark Lavender) Filter 181 (Congo Blue) Filter 197 (Alice Blue) Filter 201 (Full C.T. Blue) Filter 202 (Half C.T. Blue) Filter 203 (Quarter C.T. Blue) Filter 204 (Full C.T. Orange) Filter 219 (Fluorescent Green) Filter 206 (Quarter C.T. Orange) Filter 247 (Filter Minus Green) Filter 248 (Half Minus Green) Filter 281 (Three Quarter C.T. Blue) Filter 285 (Three Quarter C.T. Orange) Filter 352 (Glacier Blue) Filter 353 (Lighter Blue) Filter 507 (Madge) Filter 778 (Millennium Gold) Filter 793 (Vanity Fair)
Red (DMX)
110 136
24 79 153 255 245 230 99 199 255 255 225 181
0 0 255 255 255
Green (DMX)
0 43
0 193 223 248 213 131 148 152
79 138 255 121 161 115
31 65
0
Blue (DMX)
21 181 255 154
66 34 14
3 16
0 0 0 99 0 49 21 0 0 13
White (DMX)
255 120
9 36 156 116 147
3 50 60 187 112 189 15 90 97
0 0 16
2
Adobe PDF Library 15.0 Adobe InDesign CC 2015 (Windows)