RFD

Index of /fsm/coupe/2007 Coupe Roadster/

Index of /fsm/coupe/2007/

Google Docs
Google Drive
Download [pdf]

File Info : application/pdf, 60 Pages, 2.37MB

rfd

REAR FINAL DRIVE
D DRIVELINE/AXLE

RFD A

SECTION

REAR FINAL DRIVE C

RFD

CONTENTS

PRECAUTIONS ......................................................... 2

COMPONENTS .................................................. 17 F

Service Notice or Precautions ................................. 2

REMOVAL .......................................................... 17

PREPARATION .......................................................... 3

INSTALLATION .................................................. 18

Special Service Tools .............................................. 3 Commercial Service Tools ....................................... 6

Disassembly and Assembly (R200 2-pinion) ......... 19 G COMPONENTS .................................................. 19

NOISE, VIBRATION AND HARSHNESS (NVH)

ASSEMBLY INSPECTION AND ADJUSTMENT... 20

TROUBLESHOOTING ............................................... 7 NVH Troubleshooting Chart .................................... 7

DISASSEMBLY .................................................. 24 INSPECTION AFTER DISASSEMBLY ............... 28

DESCRIPTION ........................................................... 8

ADJUSTMENT AND SELECTION OF ADJUST-

Cross-Sectional View .............................................. 8 DIFFERENTIAL GEAR OIL ....................................... 9

ING WASHERS .................................................. 28 ASSEMBLY ........................................................ 33 I

Changing Differential Gear Oil ................................ 9 Disassembly and Assembly (R200V LSD) ............ 39

DRAINING ............................................................ 9

COMPONENTS .................................................. 39

FILLING ................................................................ 9

ASSEMBLY INSPECTION AND ADJUSTMENT... 40 J

Checking Differential Gear Oil ................................. 9

DISASSEMBLY .................................................. 44

OIL LEAKAGE AND OIL LEVEL .......................... 9

INSPECTION AFTER DISASSEMBLY ............... 48

FRONT OIL SEAL ................................................... 10 Removal and Installation ....................................... 10

ADJUSTMENT AND SELECTION OF ADJUST-

ING WASHERS .................................................. 48

IDENTIFICATION STAMP OF REPLACEMENT

ASSEMBLY ........................................................ 53

FREQUENCY OF FRONT OIL SEAL ................ 10 SERVICE DATA AND SPECIFICATIONS (SDS) ..... 59

REMOVAL ...........................................................11

General Specifications ........................................... 59 L

INSTALLATION .................................................. 12 Inspection and Adjustment .................................... 59

SIDE OIL SEAL ....................................................... 15

DRIVE GEAR RUNOUT ..................................... 59

Removal and Installation ....................................... 15

DIFFERENTIAL SIDE GEAR CLEARANCE ...... 59 M

REMOVAL .......................................................... 15

PRELOAD TORQUE .......................................... 59

INSTALLATION .................................................. 15

BACKLASH ........................................................ 59

REAR FINAL DRIVE ASSEMBLY ........................... 17

COMPANION FLANGE RUNOUT ...................... 59

Removal and Installation ....................................... 17

SELECTIVE PARTS ........................................... 60

Revision: 2006 November

RFD-1

2007 350Z

PRECAUTIONS

PFP:00001

Service Notice or Precautions

NDS00009

q Check for the correct installation status prior to removal or disassembly. If matching marks are required, be certain they do not interfere with the function of the parts when applied.
q Overhaul should be done in a clean work area, it is preferable to work in dustproof area.

q Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of the unit, preventing them from entering into the unit during disassembly or assembly.

q Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them with a new ones if necessary.

q Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
q In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tightening sequence is specified, observe it.

q Clean and flush the parts sufficiently and blow-dry them.

q Be careful not to damage sliding surfaces and mating surfaces.
q When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil, and foreign materials from the application and mounting surfaces.
q Always use shop paper for cleaning the inside of components.
q Avoid using cotton gloves or shop rags to prevent entering of lint.
q During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multipurpose grease as specified for each vehicle, if necessary.

Revision: 2006 November

RFD-2

2007 350Z

PREPARATION

Special Service Tools
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number (Kent-Moore No.) Tool name

Description

PFP:00002
A
NDS0000A
B

KV40104000 (--) Flange wrench a: 85 mm (3.35 in) dia. b: 65 mm (2.56 in) dia.

Removing and installing drive pinion lock nut

RFD

KV381054S0 (J-34286) Puller

NT659

Removing front oil seal

ST30720000 (J-25405) Drift a: 77 mm (3.03 in) dia. b: 55.5 mm (2.185 in) dia.
KV40104100 (--) Attachment
ST36230000 (J-25840-A) Sliding hammer
KV38100200 (J-26233) Drift a: 65 mm (2.56 in) dia. b: 49 mm (1.93 in) dia.
KV38107900 (J-39352) Protector

ZZA0601D

q Installing front oil seal

q Installing pinion rear bearing outer race
H

I
ZZA0811D
Removing side flange
J

K
ZZA0804D
Removing side flange
L

ZZA0803D

Installing side oil seal

ZZA1143D

Installing side flange

Revision: 2006 November

S-NT129
RFD-3

2007 350Z

Tool number (Kent-Moore No.) Tool name
KV38100800 (J-25604-01) Attachment a: 541 mm (21.30 in) b: 200 mm (7.87 in)
ST3127S000 (J-25765-A) Preload gauge 1: GG91030000
(J-25765) Torque wrench 2: HT62940000 (--) Socket adapter (1/2) 3: HT62900000 (--) Socket adapter (3/8) KV10111100 (J-37228) Seal cutter
ST3306S001 (J-22888-D) Differential side bearing puller set 1: ST33051001
(J-22888-20) Puller 2: ST33061000 (J-8107-2) Base a: 28.5 mm (1.122 in) dia. b: 38 mm (1.50 in) dia. ST30031000 (J-22912-01) Replacer
KV40105230 (--) Drift a: 92 mm (3.62 in) dia. b: 86 mm (3.39 in) dia. c: 45 mm (1.77 in) dia.

PREPARATION
Description Fixing unit assembly

SDIA0267E

Measuring pinion bearing preload and total preload

NT124
Removing rear cover

S-NT046

Removing and installing side bearing inner race

NT072
Removing pinion rear bearing inner race

ZZA0700D

Installing pinion rear bearing outer race

PDIA0591E

Revision: 2006 November

RFD-4

2007 350Z

Tool number (Kent-Moore No.) Tool name ST30613000 (J-25742-3) Drift a: 72 mm (2.83 in) dia. b: 48 mm (1.89 in) dia.
ST30611000 (J-25742-1) Drift bar
ST30901000 (J-26010-01) Drift a: 79 mm (3.11 in) dia. b: 45 mm (1.77 in) dia. c: 35.2 mm (1.386 in) dia.
KV38100300 (J-25523) Drift a: 54 mm (2.13 in) dia. b: 46 mm (1.81 in) dia. c: 32 mm (1.26 in) dia.
(J-8129) Spring gauge
(J-34309) Differential shim selector tool
(J-25269-4) Side bearing disc (2 Req'd)
Revision: 2006 November

PREPARATION

ZZA1000D S-NT090 ZZA0978D ZZA1046D NT127

Description

Installing pinion front bearing outer race
B

Installing pinion front bearing outer race (Use with ST30613000)

RFD

F
Installing pinion rear bearing inner race
G

H
Installing side bearing inner race
I

J
Measuring turning torque
K

Adjusting bearing preload and pinion gear

height

NT134
Selecting pinion height adjusting washer

NT136
RFD-5

2007 350Z

Commercial Service Tools
Tool name
Spacer a: 60 mm (2.36 in) dia. b: 36 mm (1.42 in) dia. c: 30 mm (1.18 in)

PREPARATION
NDS0000B
Description Installing pinion front bearing inner race

Power tool

ZZA1133D

Loosening nuts and bolts

PBIC0190E

Revision: 2006 November

RFD-6

2007 350Z

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING NVH Troubleshooting Chart

Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts. B

Reference page

I
Possible cause and SUSPECTED PARTS
J

Symptom ×: Applicable

Revision: 2006 November

Noise

K
×××××××××××××
L

RFD-7

Gear tooth rough

Refer to RFD-28 (R200 2-pinion), RFD-48 (R200V LSD).

Gear contact improper

Refer to RFD-21 (R200 2-pinion), RFD-41 (R200V LSD).

Tooth surfaces worn

Refer to RFD-28 (R200 2-pinion), RFD-48 (R200V LSD).

Backlash incorrect

Refer to RFD-22 (R200 2-pinion), RFD-42 (R200V LSD).

Companion flange excessive runout Refer to RFD-23 (R200 2-pinion), RFD-43 (R200V LSD).

Gear oil improper

Refer to RFD-9 .

PROPELLER SHAFT

NVH in PR section

AXLE AND SUSPENSION

NVH in FAX, RAX, FSU and RSU sections

TIRES

NVH in WT section

ROAD WHEEL

NVH in WT section

DRIVE SHAFT

NVH in RAX section

PFP:00003
A
NDS0000C

2007 350Z

BRAKES

NVH in BR section

STEERING

NVH in PS section

RFD E

DESCRIPTION Cross-Sectional View

DESCRIPTION
R200 (2-pinion)

PFP:00000
NDS0000D

1. Side flange 4. Pinion mate shaft 7. Drive pinion 10. Collapsible spacer

2. Pinion mate gear 5. Differential case 8. Pinion front bearing 11. Pinion rear bearing
R200V (LSD)

3. Drive gear 6. Side bearing 9. Companion flange 12. Side gear

PDIA0627E

1. Side flange 4. Pinion mate shaft 7. Side gear 10. Companion flange 13. Viscous coupling

2. Pinion mate gear 5. Differential case 8. Drive pinion 11. Collapsible spacer

Revision: 2006 November

RFD-8

3. Drive gear 6. Side bearing 9. Pinion front bearing 12. Pinion rear bearing

PDIA0628E

2007 350Z

DIFFERENTIAL GEAR OIL
DIFFERENTIAL GEAR OIL Changing Differential Gear Oil
DRAINING 1. Stop engine. 2. Remove drain plug and drain gear oil. 3. Set a gasket on drain plug and install it to final drive assembly
and tighten to the specified torque. Refer to RFD-19, "COMPONENTS" (R200 2-pinion) or RFD-39, "COMPONENTS" (R200V LSD). CAUTION: Do not reuse gasket.
FILLING 1. Remove filler plug. Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
Oil grade and Viscosity: Refer to MA-11, "Fluids and Lubricants" .
Oil capacity: Approx. 1.4 (3 US pt, 2-1/2 Imp pt)
2. After refilling oil, check oil level. Set a gasket to filler plug, then install it to final drive assembly. Refer to RFD-19, "COMPONENTS" (R200 2-pinion) or RFD-39, "COMPONENTS" (R200V LSD). CAUTION: Do not reuse gasket.
Checking Differential Gear Oil
OIL LEAKAGE AND OIL LEVEL q Make sure that oil is not leaking from final drive assembly or around it. q Check oil level from filler plug mounting hole as shown in the fig-
ure. CAUTION: Do not start engine while checking oil level. q Set a gasket on filler plug and install it on final drive assembly. Refer to RFD-19, "COMPONENTS" (R200 2-pinion) or RFD-39, "COMPONENTS" (R200V LSD). CAUTION: Do not reuse gasket.

PFP:KLD30
A
NDS0000E
B

RFD

E
PDIA0493E
F

G H

PDIA0494E

J
NDS0000F
K

PDIA0494E

Revision: 2006 November

RFD-9

2007 350Z

FRONT OIL SEAL

PFP:38189

Removal and Installation

NDS0000G

CAUTION: Verify identification stamp of replacement frequency put in the lower part of gear carrier to determine replacement for collapsible spacer when replacing front oil seal. Refer to RFD-10, "IDENTIFICATION STAMP OF REPLACEMENT FREQUENCY OF FRONT OIL SEAL" . If necessary collapsible spacer replacement, remove final drive assembly and disassemble it to replace front oil seal and collapsible spacer. Refer to RFD-17, "Removal and Installation" , RFD-19, "Disassembly and Assembly (R200 2pinion)" and/or RFD-39, "Disassembly and Assembly (R200V LSD)" .
NOTE: The reuse of collapsible spacer is prohibited in principle. However, it is reusable on a one-time basis only in cases when replacing front oil seal.

IDENTIFICATION STAMP OF REPLACEMENT FREQUENCY OF FRONT OIL SEAL
q The diagonally shaded area in the figure shows stamping point for replacement frequency of front oil seal.
q The following table shows if collapsible spacer replacement is needed before replacing front oil seal. When collapsible spacer replacement is required, disassemble final drive assembly to replace collapsible spacer and front oil seal. Refer to RFD-19, "Disassembly and Assembly (R200 2pinion)" or RFD-39, "Disassembly and Assembly (R200V LSD)" .

Stamp No stamp "0" or "0" on the far right of stamp "01" or "1" on the far right of stamp

collapsible spacer replacement Not required Required Not required

PDIA0976E

CAUTION: Be sure to make a stamping after replacing front oil seal.
q After replacing front oil seal, make a stamping on the stamping point in accordance with the table below in order to identify replacement frequency.
CAUTION: Stamping shall be made from left to right.

Stamp before stamping
No stamp
"0" (Front oil seal was replaced once.)
"01" (Collapsible spacer and front oil seal were replaced last time.)
"0" is on the far right. (Only front oil seal was replaced last time.)
"1" is on the far right. (Collapsible spacer and front oil seal were replaced last time.)

Stamping on the far right 0 1 0 1 0

Stamping 0 01
010 ...01 ...010

Revision: 2006 November

RFD-10

2007 350Z

FRONT OIL SEAL

REMOVAL

1. Drain gear oil. Refer to RFD-9, "DRAINING" .

2. Make a judgment if a collapsible spacer replacement is required. Refer to RFD-10, "IDENTIFICATION STAMP OF REPLACEMENT FREQUENCY OF FRONT OIL SEAL" .

3. Remove rear wheel sensor. Refer to BRC-34, "WHEEL SENSORS" (ABS), BRC-73, "WHEEL SEN- B SORS" (TCS/ABS) or BRC-128, "WHEEL SENSORS" (VDC/TCS/ABS).

4. Remove drive shaft from final drive. Then suspend it by wire etc. Refer to RAX-10, "Removal and Installa-

tion" .

5. Install attachment to side flange, and then pull out the side flange with the sliding hammer.

Tool number A: KV40104100 ( -- )

RFD

B: ST36230000 (J-25840-A)

NOTE:

Model

Circular clip installation position

Right side

Left side

R200 (2-pinion)

Final drive side

R200V (LSD)

Final drive side

Side flange side

6. Remove propeller shaft. Refer to PR-6, "Removal and Installation" . 7. Measure the total preload with the preload gauge.

Tool number A: ST3127S000 (J-25765-A)

NOTE: Record the preload measurement.

F
SDIA1005E
G
H

8. Remove drive pinion lock nut using the flange wrench. Tool number : KV40104000 ( -- )

J
PDIA1006E
K
L

9. Put matching mark on the end of the drive pinion. The matching mark should be in line with the matching mark A on companion flange.
CAUTION: For matching mark, use paint. Do not damage drive pinion.
NOTE: The matching mark A on the final drive companion flange indicates the maximum vertical runout position.

SDIA1142E PDIA0629E

Revision: 2006 November

RFD-11

2007 350Z

FRONT OIL SEAL
10. Remove companion flange using a puller.
11. Remove front oil seal using the puller. Tool number A: KV381054S0 (J-34286)
INSTALLATION 1. Apply multi-purpose grease to front oil seal lips. 2. Install front oil seal using the drift as shown in the figure.
Tool number A: ST30720000 (J-25405) CAUTION: q Do not reuse oil seal. q Do not incline oil seal when installing.
3. Align the matching mark of drive pinion with the matching mark of companion flange, and then install the companion flange.

Revision: 2006 November

RFD-12

PDIA0630E PDIA0980E PDIA0752J PDIA0629E
2007 350Z

FRONT OIL SEAL

4. Apply anti-corrosion oil to the thread and seat of new drive pin-

ion lock nut, and temporarily tighten drive pinion lock nut to drive

pinion.

CAUTION:

Do not reuse drive pinion lock nut.

5. Tighten to drive pinion lock nut, while adjust total preload torque.

Tool number A: ST3127S000 (J-25765-A) C
Drive pinion lock nut tightening torque:
147 323 N·m (15 32 kg-m, 109 238 ft-lb) RFD
Total preload torque:

Total preload torque should equal the measurement

taken during removal plus an additional 0.1 0.4 N·m

(0.01 0.04 kg-m, 1 3 in-lb).

CAUTION:

q Adjust to the lower limit of the drive pinion lock nut tight-

ening torque first.

q If the preload torque exceeds the specified value, replace collapsible spacer and tighten it again to adjust. Do not loosen drive pinion lock nut to adjust the preload torque.

G
PDIA1007E

6. Make a stamping for identification of front oil seal replacement

frequency. Refer to RFD-10, "IDENTIFICATION STAMP OF REPLACEMENT FREQUENCY OF FRONT OIL SEAL" .

CAUTION:

Be sure to make a stamping after replacing front oil seal.

7. Install propeller shaft. Refer to PR-6, "Removal and Installation" .

8. Install side flange with the following procedure.

NOTE:

Install the RH side flange, then install the LH side flange. If LH side flange is installed first, the RH side

flange comes out sometimes from the shock of installing the RH side flange. [For R200V (with LSD)]

a. Attach the protector to side oil seal.

Tool number : KV38107900 (J-39352)

b. After the side flange is inserted and the serrated part of side

gear has engaged the serrated part of flange, remove the pro-

tector.

SDIA0822E

Revision: 2006 November

RFD-13

2007 350Z

FRONT OIL SEAL
c. Put a suitable drift on the center of side flange, then drive it until sound changes. NOTE: When installation is completed, driving sound of the side flange turns into a sound which seems to affect the whole final drive.
d. Confirm that the dimension of the side flange installation (Measurement A) in the figure comes into the following.
Measurement A: 326 328 mm (12.83 12.91 in)
9. Install drive shaft. Refer to RAX-10, "Removal and Installation" . 10. Install rear wheel sensor. Refer to BRC-34, "WHEEL SEN-
SORS" (ABS), BRC-73, "WHEEL SENSORS" (TCS/ABS) or BRC-128, "WHEEL SENSORS" (VDC/TCS/ABS). 11. Refill gear oil to the final drive and check oil level. Refer to RFD9, "FILLING" . 12. Check the final drive for oil leakage. Refer to RFD-9, "OIL LEAKAGE AND OIL LEVEL" .

PDIA0631E

Revision: 2006 November

RFD-14

2007 350Z

SIDE OIL SEAL

SIDE OIL SEAL
Removal and Installation
REMOVAL

PFP:33142
A
NDS0000H

1. Remove rear wheel sensor. Refer to BRC-34, "WHEEL SENSORS" (ABS), BRC-73, "WHEEL SENSORS" (TCS/ABS) or BRC-128, "WHEEL SENSORS" (VDC/TCS/ABS).

2. Remove drive shaft from final drive. Then suspend it by wire etc. Refer to RAX-10, "Removal and Installa-

tion" .

3. Install attachment to side flange, and then pull out the side

flange with the sliding hammer.

Tool number A: KV40104100 ( -- )

RFD

B: ST36230000 (J-25840-A)

NOTE:

Model

Circular clip installation position

Right side

Left side

R200 (2-pinion) R200V (LSD)

Final drive side

Side flange side

F
SDIA1005E

4. Remove side oil seal, using a flat-bladed screwdriver.

CAUTION: Be careful not to damage gear carrier.
H

INSTALLATION 1. Apply multi-purpose grease to side oil seal lips.
2. Install side oil seal until it becomes flush with the case end, using the drift.
Tool number : KV38100200 (J-26233)
CAUTION: q Do not reuse oil seal.
q When installing, do not incline oil seal.
3. Install side flange with the following procedure.
NOTE: Install the RH side flange, then install the LH side flange. If LH side flange is installed first, the RH side flange comes out sometimes from the shock of installing the RH side flange. [For R200V (with LSD)]

J
SDIA1036E
K L M
SDIA1037E

Revision: 2006 November

RFD-15

2007 350Z

SIDE OIL SEAL
a. Attach the protector to side oil seal. Tool number : KV38107900 (J-39352)
b. After the side flange is inserted and the serrated part of side gear has engaged the serrated part of flange, remove the protector.
c. Put a suitable drift on the center of side flange, then drive it until sound changes. NOTE: When installation is completed, driving sound of the side flange turns into a sound which seems to affect the whole final drive.
d. Confirm that the dimension of the side flange installation (Measurement A) in the figure comes into the following. Measurement A: 326 - 328 mm (12.83 - 12.91 in)
4. Install drive shaft. Refer to RAX-10, "Removal and Installation" . 5. Install rear wheel sensor. Refer to BRC-34, "WHEEL SEN-
SORS" (ABS), BRC-73, "WHEEL SENSORS" (TCS/ABS) or BRC-128, "WHEEL SENSORS" (VDC/TCS/ABS).

SDIA0822E PDIA0631E

Revision: 2006 November

RFD-16

2007 350Z

REAR FINAL DRIVE ASSEMBLY
REAR FINAL DRIVE ASSEMBLY Removal and Installation
COMPONENTS

1. Rear final drive assembly 4. Washer

2. Upper stopper 5. Lower stopper

3. Propeller shaft 6. Drive shaft

REMOVAL 1. Remove propeller shaft from the final drive. Refer to PR-6, "Removal and Installation" .
CAUTION: Do not impact or damage propeller shaft tube.
2. Remove rear stabilizer bar with a power tool. Refer to FSU-18, "STABILIZER BAR" .
3. Remove drive shaft from final drive. Then suspend it by wire etc. Refer to RAX-10, "REAR DRIVE SHAFT" .
4. Remove breather hose from the final drive.
5. Remove rear wheel sensor. Refer to BRC-34, "WHEEL SENSORS" (ABS), BRC-73, "WHEEL SENSORS" (TCS/ABS) or BRC-128, "WHEEL SENSORS" (VDC/TCS/ABS).

PFP:38300
A
NDS0000I
B

RFD

G H

PDIA0632E

SDIA1094E

Revision: 2006 November

RFD-17

2007 350Z

REAR FINAL DRIVE ASSEMBLY
6. Set a suitable jack to rear final drive assembly. CAUTION: Do not place a suitable jack on the rear cover (aluminum case).
7. Remove the mounting bolts and nuts connecting to the suspension member, and remove rear final drive assembly. CAUTION: Secure rear final drive assembly to a suitable jack while removing it.

PDIA0690E

SDIA1970J

INSTALLATION

Note the following, and installation is in the reverse order of removal.

q Refer to RFD-19, "COMPONENTS" (R200 2-pinion) or RFD-39, "COMPONENTS" (R200V LSD) about each tightening torque.

q When installing breather hoses, refer to the figure.

CAUTION: Make sure there are no pinched or restricted areas on the breather hose caused by bending or winding when installing it.

For installation, the vehicle side end shall be inserted to suspension member. Install metal connector side of this hose to rear cover by inserting it with aiming painted marking to the front of vehicle.

q When oil leaks while removing final drive assembly, check oil level after the installation. Refer to RFD-9, "Checking Differential Gear Oil" .

PDIA0633E

Revision: 2006 November

RFD-18

2007 350Z

REAR FINAL DRIVE ASSEMBLY
Disassembly and Assembly (R200 2-pinion)
COMPONENTS

NDS0000J
A
B

RFD

PDIA1134E

1. Drive pinion lock nut

2. Companion flange

3. Front oil seal

4. Pinion front bearing

5. Gear carrier

6. Side oil seal

7. Side flange

8. Collapsible spacer

9. Pinion rear bearing

10. Pinion height adjusting washer

11. Drive pinion

12. Side bearing adjusting washer

13. Side bearing

14. Side gear thrust washer

15. Circular clip

16. Side gear

17. Lock pin

18. Pinion mate gear

19. Pinion mate thrust washer

20. Pinion mate shaft

21. Drive gear

22. Differential case

23. Bearing cap

24. Filler plug

25. Gasket

26. Rear cover

27. Drain plug

A: Oil seal lip

B: Screw hole

C: After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.

Refer to GI-11, "Components" and the followings for the symbols in the figure. : Apply gear oil. : Apply anti-corrosion oil. : Apply Genuine Silicone RTV or equivalent. Refer to GI-45, "Recommended Chemical Products and Sealants" . Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to GI-45, "Recommended Chemical Prod: ucts and Sealants" .

Revision: 2006 November

RFD-19

2007 350Z

REAR FINAL DRIVE ASSEMBLY

ASSEMBLY INSPECTION AND ADJUSTMENT q Before inspection and adjustment, drain gear oil.
Total Preload Torque 1. Secure final drive assembly onto an attachment.
Tool number : KV38100800 (J-25604-01)
2. Remove side flanges. 3. Rotate drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction. 4. Rotate drive pinion at least 20 times to check for smooth opera-
tion of the bearing. 5. Measure total preload with the preload gauge.
Tool number : ST3127S000 (J-25765-A)

Total preload torque:
2.85 3.75 N·m (0.29 0.38 kg-m, 26 33 in-lb)
NOTE: Total preload torque = Pinion bearing preload torque + Side bearing preload torque
q If measured value is out of the specification, disassemble it to check and adjust each part. Adjust the pinion bearing preload and side bearing preload. Adjust the pinion bearing preload first, then adjust the side bearing preload.

PDIA0635E

When the preload torque is large

On pinion bearings: Replace the collapsible spacer.

On side bearings:

Use thinner side bearing adjusting washers by the same amount to each side. Refer to RFD-60, "Side Bearing Adjusting Washer" .

When the preload is small

On pinion bearings: Tighten the drive pinion lock nut.

On side bearings:

Use thicker side bearing adjusting washers by the same amount to each side. Refer to RFD-60, "Side Bearing Adjusting Washer" .

Drive Gear Runout 1. Remove rear cover. Refer to RFD-24, "Differential Assembly" . 2. Fit a dial indicator to the drive gear back face. 3. Rotate the drive gear to measure runout.

Runout limit: 0.05 mm (0.0020 in) or less
q If the runout is outside of the repair limit, check drive gear assembly condition; foreign material may be caught between drive gear and differential case, or differential case or drive gear may be deformed, etc.
CAUTION: Replace drive gear and drive pinion gear as a set.
SPD886

Revision: 2006 November

RFD-20

2007 350Z

REAR FINAL DRIVE ASSEMBLY
Tooth Contact 1. Remove rear cover. Refer to RFD-24, "Differential Assembly" . 2. Apply red lead to drive gear.
CAUTION: Apply red lead to both the faces of 3 to 4 gears at 4 locations evenly spaced on drive gear.
3. Rotate drive gear back and forth several times, check drive pinion gear to drive gear tooth contact. CAUTION: Check tooth contact on drive side and reverse side.

SPD357

RFD E

SDIA0570E

Revision: 2006 November

RFD-21

SDIA0207E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
4. If tooth contact is improperly adjusted, follow the procedure below to adjust the pinion height (dimension X).

q If the tooth contact is near the face (face contact), or near the heel (heel contact), thicken pinion height adjusting washers to move drive pinion closer to drive gear. Refer to RFD-60, "Pinion Height Adjusting Washer" .

SDIA0517E

q If the tooth contact is near the flank (flank contact), or near the toe (toe contact), thin pinion height adjusting washers to move drive pinion farther from drive gear. Refer to RFD-60, "Pinion Height Adjusting Washer" .

PDIA0440E

Backlash 1. Remove rear cover. Refer to RFD-24, "Differential Assembly" .
2. Fit a dial indicator to the drive gear face to measure the backlash.

Backlash:

0.10 0.15 mm (0.0039 0.0059 in)

q If the backlash is outside of the specified value, change the thickness of side bearing adjusting washer.

When the backlash is large:
Make drive gear back side adjusting washer thicker, and drive gear tooth side adjusting washer thinner by the same amount. Refer to RFD-60, "Side Bearing Adjusting Washer" .
When the backlash is small:
Make drive gear back side adjusting washer thinner, and drive gear tooth side adjusting washer thicker by the same amount. Refer to RFD-60, "Side Bearing Adjusting Washer" .
CAUTION: Do not change the total amount of washers as it will change the bearing preload.

Revision: 2006 November

RFD-22

PDIA0441E SPD513
2007 350Z

REAR FINAL DRIVE ASSEMBLY

Companion Flange Runout

1. Fit a dial indicator onto the companion flange face (inner side of

the propeller shaft mounting bolt holes).

2. Rotate the companion flange to check for runout.

B Runout limit : 0.08 mm (0.0031 in)

3. Fit a test indicator to the inner side of the companion flange

(socket diameter).

4. Rotate the companion flange to check for runout.

Runout limit : 0.08 mm (0.0031 in)
5. If the runout value is outside the repair limit, follow the procedure below to adjust.

PDIA0646E

RFD

a. Check for runout while changing the phase between companion flange and drive pinion gear by 90° step, and search for the position where the runout is the minimum.

b. If the runout value is still outside of the limit after the phase has been changed, possible cause will be an

assembly malfunction of drive pinion and pinion bearing and malfunction of pinion bearing. Check for

these items and repair if necessary.

c. If the runout value is still outside of the limit after the check and repair, replace companion flange.

Revision: 2006 November

RFD-23

2007 350Z

REAR FINAL DRIVE ASSEMBLY
DISASSEMBLY Differential Assembly 1. Drain gear oil, if necessary. 2. Remove side flange. 3. Remove rear cover mounting bolts. 4. Remove rear cover to insert the seal cutter between gear carrier
and rear cover. Tool number : KV10111100 (J-37228)
CAUTION: q Be careful not to damage the mating surface. q Do not insert flat-bladed screwdriver, this way damage
the mating surface.
5. Using two 45 mm (1.77 in) spacers, mount carrier on the attachment. Tool number : KV38100800 (J-25604-01)
6. For proper reinstallation, paint matching marks on one side of the bearing cap. CAUTION: q For matching marks, use paint. Do not damage bearing caps and gear carrier. q Bearing caps are line-board during manufacture. The matching marks are used to reinstall them in their original positions.
7. Remove bearing caps.

PDIA0491E SPD888 SDIA1795E

Revision: 2006 November

RFD-24

S-PD343
2007 350Z

REAR FINAL DRIVE ASSEMBLY
8. Lift differential case assembly out with a suitable tool.

q Keep side bearing outer races together with inner race. Do not mix them up. Also, keep side bearing adjusting washers together with bearings.

9. Remove side bearing inner race. To prevent damage to bearing, engage puller jaws in groove.

Tool number

A: ST33051001 (J-22888-20) B: ST33061000 (J-8107-2)

CAUTION: q To prevent damage to the side bearing and drive gear,
place copper plates between these parts and vise.
q It is not necessary to remove side bearing inner race except it is replaced.

10. For proper reinstallation, paint matching marks on one differential case assembly.
CAUTION: For matching marks, use paint. Do not damage differential case and drive gear.
11. Remove drive gear mounting bolts.
12. Tap drive gear off differential case assembly with a soft hammer.
CAUTION: Tap evenly all around to keep drive gear from bending.

Revision: 2006 November

RFD-25

PDIA0547E

RFD

G
SPD527
H

SPD920

PDIA0496E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
13. Remove lock pin of pinion mate shaft with a punch from drive gear side.
SPD025
14. Remove pinion mate shaft.

15. Turn pinion mate gear, then remove pinion mate gear, pinion mate thrust washer, side gear and side gear thrust washer from differential case.
Drive Pinion Assembly 1. Remove differential assembly. Refer to RFD-24, "Differential Assembly" . 2. Remove drive pinion lock nut with the flange wrench.
Tool number : KV40104000 ( -- )

SDIA0031J SDIA0032J SDIA1144E

Revision: 2006 November

RFD-26

2007 350Z

REAR FINAL DRIVE ASSEMBLY
3. Put matching mark on the end of drive pinion. The matching mark should be in line with the matching mark A on companion flange. CAUTION: For matching mark, use paint. Do not damage companion flange and drive pinion. NOTE: The matching mark A on the final drive companion flange indicates the maximum vertical runout position. When replacing companion flange, matching mark is not necessary.
4. Remove companion flange using the suitable puller.

5. Press drive pinion assembly out of gear carrier. CAUTION: Do not drop drive pinion assembly.
6. Remove front oil seal. 7. Remove side oil seal. 8. Remove pinion front bearing inner race. 9. Remove collapsible spacer.
10. Remove pinion rear bearing inner race and drive pinion height adjusting washer with the replacer. Tool number : ST30031000 (J-22912-01)
11. Tap pinion front/rear bearing outer races uniformly a brass rod or equivalent to removed. CAUTION: Be careful not to damage gear carrier.

Revision: 2006 November

RFD-27

PDIA0629E

RFD

G
SDIA1132E
H

I
J
SPD892
K
L

S-PD179

SDIA0817E
2007 350Z

REAR FINAL DRIVE ASSEMBLY

INSPECTION AFTER DISASSEMBLY
Clean up the disassembled parts. Then, inspect if the parts are worn or damaged. If so, follow the measures below.

Content
Hypoid gear
Bearing Side gear and Pinion mate gear Side gear thrust washer and pinion mate thrust washer
Oil seal
Differential case Companion flange

Conditions and Measures q If the gear teeth do not mesh or line-up correctly, determine the cause and adjust or replace as nec-
essary. q If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new
drive gear and drive pinion as a set. q If any chipped (by friction), pitted, worn, rusted or scratched mark, or unusual noise from the bearing
is observed, replace as a bearing assembly (as a new set). q If any cracks or damage on the surface of the tooth is found, replace. q If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
q If it is chipped (by friction), damaged, or unusually worn, replace.
q Whenever disassembled, replace. q If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace
them. q If any wear or crack on the contact sides of the differential case is found, replace. q If any chipped mark (about 0.1 mm, 0.004 in) or other damage on the contact sides of the lips of the
companion flange is found, replace.

ADJUSTMENT AND SELECTION OF ADJUSTING WASHERS Differential Side Gear Clearance q Assemble the differential parts if they are disassembled. Refer to RFD-24, "Differential Assembly" . 1. Place differential case straight up so that side gear to be mea-
sured comes upward.

PDIA0460E

Revision: 2006 November

RFD-28

2007 350Z

REAR FINAL DRIVE ASSEMBLY

2. Using feeler gauge, measure the clearance between side gear

back and differential case at 3 different points, while rotating

side gear. Average the 3 readings, and then measure the clear-

ance of the other side as well.

Side gear back clearance specification:

0.2 mm (0.008 in) or less.

(Each gear should rotate smoothly without excessive

resistance during differential motion.)

CAUTION:

To prevent side gear from tilting, insert feeler gauges with

the same thickness from both sides.

RFD

3. If the back clearance is outside the specification, use a thicker/

thinner side gear thrust washer to adjust. Refer to RFD-60,

"Side Gear Thrust Washer" .

When the back clearance is large:

Use a thicker thrust washer.

When the back clearance is small:

Use a thinner thrust washer.

CAUTION: Select a side gear thrust washer for right and left individually.

G
PDIA0576E

Side Bearing Preload

q Selecting carrier side bearing adjusting washers is required for successful completion of this procedure.

1. Make sure all parts are clean. Also, make sure the bearings are

well lubricated with gear oil.

2. Place the differential case, with side bearings and bearing races installed, into gear carrier. J

3. Insert left and right original side bearing adjusting washers in place between side bearings and gear carrier.

K
SPD527
L M

SPD558

Revision: 2006 November

RFD-29

2007 350Z

REAR FINAL DRIVE ASSEMBLY
4. Install bearing caps in their correct locations and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-19, "COMPONENTS" .
5. Turn the carrier several times to seat the bearings.

6. Measure the turning torque of the carrier at the drive gear mounting bolts with a spring gauge. Tool number : -- (J-8129)
Specification: 34.2 39.2 N (3.5 4.0 kg, 7.7 8.8 lb) of pulling force at the drive gear bolt

SDIA1795E

SPD194A

7. If the turning torque is outside the specification, use a thicker/ thinner side bearing adjusting washer to adjust. Refer to RFD60, "Side Gear Thrust Washer" .

If the turning torque is less than the specified range: Use a thicker thrust washer.
If the turning torque is greater than the specification: Use a thinner thrust washer.

CAUTION:

Select a side bearing adjusting washer for right and left

individually.

SPD772

8. Record the total amount of washer thickness required for the correct carrier side bearing preload.

Pinion Gear Height 1. Make sure all parts are clean and that the bearings are well
lubricated.
2. Assemble the pinion gear bearings into the differential shim selector tool.

Tool number : -- (J-34309)

SPD769

Revision: 2006 November

RFD-30

2007 350Z

REAR FINAL DRIVE ASSEMBLY
q Pinion front bearing; make sure the J-34309-3 pinion front bearing seat is secured tightly against the J-34309-2 gauge anvil. Then turn the pinion front bearing pilot, J-34309-5, to secure the bearing in its proper position.
q Pinion rear bearing; the pinion rear bearing pilot, J-34309-8, is used to center the pinion rear bearing only. The pinion rear bearing locking seat, J-34309-4, is used to lock the bearing to the assembly.
q Installation of J-34309-9 and J-34309-16; place a suitable 2.5 mm (0.098 in) thick plain washer between J-34309-9 and J-34309-16. Both surfaces of J-34309-9 and J-34309-16 must be parallel with a clearance of 2.5 mm (0.098 in).
3. Install the pinion rear bearing inner race into gear carrier. Then place the pinion preload shim selector tool, J-34309-1, gauge screw assembly.
4. Assemble the pinion front bearing inner race and the J-34309-2 gauge anvil. Assemble them together with the J-34309-1 gauge screw in gear carrier. Make sure that the pinion height gauge plate, J-34309-16, will turn a full 360 degrees. Tighten the two sections together by hand.
5. Turn the assembly several times to seat the bearings.

Revision: 2006 November

RFD-31

SPD197A

RFD

G
SPD893
H

I J

SPD199A

SPD770

PDIA0566E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
7. Place the J-34309-11 "R200A" pinion height adapter onto the gauge plate and tighten it by hand. CAUTION: Make sure all machined surfaces are clean.
8. Position the side bearing discs, J-25269-4, and arbor firmly into the side bearing bores. Install the bearing caps and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-19, "COMPONENTS" .
9. Select the correct standard pinion height adjusting washer thickness. Select by using a standard gauge of 3 mm (0.12 in) and your J-34309-101 feeler gauge. Measure the distance between the J-34309-11 pinion height adapter including the standard gauge and the arbor.
10. Write down exact measurement (the value of feeler gauge).

SPD208A SPD211A SPD204A

11. Correct the pinion height washer size by referring to the "pinion head number". There are two numbers painted on the drive pinion. The first one refers to the drive pinion and drive gear as a matched set. This number should be the same as the number on the drive gear. The second number is the "pinion head height number". It refers to the ideal pinion height from standard for quietest operation. Use the following chart to determine the correct pinion height washer.

Revision: 2006 November

RFD-32

SPD775
SPD542
2007 350Z

REAR FINAL DRIVE ASSEMBLY

Pinion head height number

Add or remove from the standard pinion height adjusting washer thickness measurement

- 6

Add 0.06 mm (0.0024 in)

- 5

Add 0.05 mm (0.0020 in)

- 4

Add 0.04 mm (0.0016 in)

- 3

Add 0.03 mm (0.0012 in)

- 2

Add 0.02 mm (0.0008 in)

- 1

Add 0.01 mm (0.0004 in)

Use the selected washer thickness

Subtract 0.01 mm (0.0004 in)

Subtract 0.02 mm (0.0008 in)

Subtract 0.03 mm (0.0012 in)

Subtract 0.04 mm (0.0016 in)

Subtract 0.05 mm (0.0020 in)

Subtract 0.06 mm (0.0024 in)

12. Select the correct pinion height adjusting washer. Refer to RFD-60, "Pinion Height Adjusting Washer" .
13. Remove the J-34309 differential shim selector tool from the final drive housing. Then disassemble to retrieve the pinion bearings.

A B C RFD E F

ASSEMBLY Drive Pinion Assembly 1. Install front and rear bearing outer races using drifts.
Tool number A: ST30720000 (J-25405)
B: KV40105230 ( -- )
C: ST30611000 (J-25742-1)
D: ST30613000 (J-25742-3)
CAUTION: q At first, using a hammer, tap bearing outer race until it
becomes flat to gear carrier. q Do not reuse pinion front and rear bearing outer race. 2. Select drive pinion height adjusting washer. Refer to RFD-60, "Pinion Height Adjusting Washer" .

G H
SPD205A
I J K L M

Revision: 2006 November

RFD-33

PDIA0562E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
3. Install selected drive pinion height adjusting washer to drive pinion. Press pinion rear bearing inner race to it, using drift. Tool number : ST30901000 (J-26010-01) CAUTION: q Pay attention to the direction of pinion height adjusting washer. (Assemble as shown in the figure.) q Do not reuse pinion rear bearing inner race.
4. Assemble collapsible spacer to drive pinion. CAUTION: Do not reuse collapsible spacer.
5. Apply gear oil to pinion rear bearing, and assemble drive pinion into gear carrier.
6. Apply gear oil to pinion front bearing, and assemble pinion front bearing inner race to drive pinion assembly. CAUTION: Do not reuse pinion front bearing inner race.
7. Using suitable spacer, press the pinion front bearing inner race to drive pinion as far as drive pinion nut can be tightened.

SDIA0048E PDIA0492E

8. Using the drift, install front oil seal as shown in the figure. Tool number : ST30720000 (J-25405)
CAUTION: q Do not reuse oil seal. q When installing, do not incline oil seal. q Apply multi-purpose grease onto oil seal lips, and gear
oil onto the circumference of oil seal.
9. Install companion flange. NOTE: When reusing drive pinion, align the matching mark of drive pinion with the matching mark A of companion flange, then install companion flange.

Revision: 2006 November

RFD-34

SPD896
PDIA0563E
PDIA0629E
2007 350Z

REAR FINAL DRIVE ASSEMBLY

10. Apply anti-corrosion oil to the thread and seat of drive pinion

lock nut, and temporarily tighten drive pinion lock nut to drive

pinion.

CAUTION:

Do not reuse drive pinion lock nut.

11. Adjust to the drive pinion lock nut tightening torque and pinion bearing preload torque.

Tool number A: KV40104000 ( -- )

B: ST3127S000 (J-25765-A)

Drive pinion lock nut tightening torque:

RFD

147 323 N·m (15 32 kg-m, 109 238 ft-lb)

Drive pinion bearing preload:

2.65 3.23 N·m (0.27 0.32 kg-m, 24 28 in-lb)

CAUTION:

q Adjust to the lower limit of the drive pinion lock nut tight-

ening torque first.

q If the preload torque exceeds the specified value, replace collapsible spacer and tighten it again to adjust. Do not loosen drive pinion lock nut to adjust the preload torque.

G
PDIA0636E

q After adjustment, rotate drive pinion back and forth 2 to 3 times to check for unusual noise, rota-

tion malfunction, and other malfunctions.

12. Install differential case assembly. Refer to RFD-35, "Differential Assembly" .

CAUTION:

Do not install rear cover yet.

13. Check and adjust drive gear runout, tooth contact, drive gear to drive pinion backlash, and companion

flange runout. Refer to RFD-20, "Drive Gear Runout" , RFD-21, "Tooth Contact" , RFD-22, "Backlash" and

RFD-23, "Companion Flange Runout" .

Recheck above items. Readjust the above description, if necessary.

14. Check total preload torque. Refer to RFD-20, "Total Preload Torque" .

15. Install rear cover. Refer to RFD-35, "Differential Assembly" .

Differential Assembly

1. Install side gear thrust washers with the same thickness as the

ones installed prior to disassembly or reinstall the old ones on

the side gears.

SDIA0193J

Revision: 2006 November

RFD-35

2007 350Z

REAR FINAL DRIVE ASSEMBLY
2. Install side gears and thrust washers into differential case. CAUTION: Make sure that the circular clip is installed to side gears.
3. Align 2 pinion mate gears in diagonally opposite positions, then rotate and install them into differential case after installing thrust washer to pinion mate gear.
4. Align the lock pin holes on differential case with shaft, and install pinion mate shaft.
5. Measure side gear end play. If necessary, select the appropriate side gear thrust washers. Refer to RFD-59, "DIFFERENTIAL SIDE GEAR CLEARANCE" .
6. Drive a lock pin into pinion mate shaft, using a punch. Make sure lock pin is flush with differential case. CAUTION: Do not reuse lock pin.
7. Align the matching mark of differential case with the mark of drive gear, then place drive gear.

SDIA2025E SDIA0195J SPD030

8. Apply thread locking sealant into the thread hole of drive gear.
q Use Genuine High Strength Thread Locking Sealant or equivalent. Refer to GI-45, "Recommended Chemical Products and Sealants" .
CAUTION: Drive gear back and threaded holes shall be cleaned and degreased sufficiently.

Revision: 2006 November

RFD-36

SDIA2593E
SDIA2594E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
9. Install drive gear on the mounting bolts, and then tighten to the specified torque. Refer to RFD-19, "COMPONENTS" . CAUTION: q Tighten bolts in a crisscross fashion. q After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.
10. Press side bearing inner races to differential case, using the drift and the base. Tool number A: KV38100300 (J-25523) B: ST33061000 (J-8107-2) CAUTION: Do not reuse side bearing inner race.
11. Install differential case assembly with side bearing outer races into gear carrier.
12. Measure side bearing preload. If necessary, select the appropriate side bearing adjusting washers. Refer to RFD-29, "Side Bearing Preload" .
13. Insert selected left and right side bearing adjusting washers in place between side bearings and gear carrier.

14. Align matching marks on bearing cap with that on gear carrier.
15. Install bearing caps and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-19, "COMPONENTS" .

Revision: 2006 November

RFD-37

SDIA0247J

RFD

G
SPD353
H

I J

SPD527

SPD558

SDIA1795E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
16. Using the drift, drive side oil seals until it becomes flush with the case end. Tool number : KV38100200 (J-26233) CAUTION: q Do not reuse oil seal. q When installing, do not incline oil seal. q Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference of oil seal.
17. Check and adjust drive gear runout, tooth contact, drive gear to drive pinion backlash, and total preload torque. Refer to RFD20, "Drive Gear Runout" , RFD-21, "Tooth Contact" , RFD-22, "Backlash" and RFD-20, "Total Preload Torque" . Recheck above items. Readjust the above description, if necessary.
18. Apply sealant to mating surface of rear cover. q Use Genuine Silicone RTV or equivalent. Refer to GI-45, "Recommended Chemical Products and Sealants" . CAUTION: Remove old sealant adhering to mounting surfaces. Also remove any moisture, oil, or foreign material adhering to application and mounting surfaces.
19. Install rear cover on gear carrier and tighten mounting bolts with the specified torque. Refer to RFD-19, "COMPONENTS" .
20. Install side flange with the following procedure. a. Attach the protector to side oil seal.
Tool number : KV38107900 (J-39352) b. After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the protector.
c. Put a suitable drift on the center of side flange, then drive it until sound changes. NOTE: When installation is completed, driving sound of the side flange turns into a sound which seems to affect the whole final drive.
d. Confirm that the dimension of the side flange installation (Measurement A) in the figure comes into the following.
Measurement A: 326 328 mm (12.83 12.91 in)

SPD560 PDIA0961E SDIA0822E PDIA0637E

Revision: 2006 November

RFD-38

2007 350Z

REAR FINAL DRIVE ASSEMBLY
Disassembly and Assembly (R200V LSD)
COMPONENTS

NDS0000K
A
B

RFD

PDIA1135E

1. Drive pinion lock nut

2. Companion flange

3. Front oil seal

4. Pinion front bearing

5. Gear carrier

6. Side oil seal

7. Side flange

8. Collapsible spacer

9. Pinion rear bearing

10. Pinion height adjusting washer

11. Drive pinion

12. Side bearing adjusting washer

13. Side bearing

14. Drive gear

15. Differential case B

16. Side gear thrust washer

17. Circular clip

18. Side gear

19. Pinion mate shaft

20. Pinion mate thrust washer

21. Pinion mate gear

22. Viscous coupling

23. Differential case A

24. Bearing cap

25. Filler plug

26. Gasket

27. Rear cover

28. Drain plug

A: Oil seal lip

B: Screw hole

C: After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.

Revision: 2006 November

RFD-39

2007 350Z

REAR FINAL DRIVE ASSEMBLY

PDIA0635E

When the preload torque is large

On pinion bearings: Replace the collapsible spacer.

On side bearings:

Use thinner side bearing adjusting washers by the same amount to each side. Refer to RFD-60, "Side Bearing Adjusting Washer" .

When the preload is small

On pinion bearings: Tighten the drive pinion lock nut.

On side bearings:

Use thicker side bearing adjusting washers by the same amount to each side. Refer to RFD-60, "Side Bearing Adjusting Washer" .

Drive Gear Runout 1. Remove rear cover. Refer to RFD-44, "Differential Assembly" . 2. Fit a dial indicator to the drive gear back face. 3. Rotate the drive gear to measure runout.

Revision: 2006 November

RFD-40

2007 350Z

REAR FINAL DRIVE ASSEMBLY
Tooth Contact 1. Remove rear cover. Refer to RFD-44, "Differential Assembly" . 2. Apply red lead to drive gear.
CAUTION: Apply red lead to both the faces of 3 to 4 gears at 4 locations evenly spaced on drive gear.
3. Rotate drive gear back and forth several times, check drive pinion gear to drive gear tooth contact. CAUTION: Check tooth contact on drive side and reverse side.

SPD357

RFD E

SDIA0570E

Revision: 2006 November

RFD-41

SDIA0207E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
4. If tooth contact is improperly adjusted, follow the procedure below to adjust the pinion height (dimension X).

SDIA0517E

PDIA0440E

Backlash 1. Remove rear cover. Refer to RFD-44, "Differential Assembly" .
2. Fit a dial indicator to the drive gear face to measure the backlash.

Backlash:

0.10 0.15 mm (0.0039 0.0059 in)

q If the backlash is outside of the specified value, change the thickness of side bearing adjusting washer.

Revision: 2006 November

RFD-42

PDIA0441E SPD513
2007 350Z

REAR FINAL DRIVE ASSEMBLY

Companion Flange Runout

1. Fit a dial indicator onto the companion flange face (inner side of

the propeller shaft mounting bolt holes).

2. Rotate the companion flange to check for runout.

B Runout limit : 0.08 mm (0.0031 in)

3. Fit a test indicator to the inner side of the companion flange

(socket diameter).

4. Rotate the companion flange to check for runout.

Runout limit : 0.08 mm (0.0031 in)
5. If the runout value is outside the repair limit, follow the procedure below to adjust.

PDIA0646E

RFD

a. Check for runout while changing the phase between companion flange and drive pinion gear by 90° step, and search for the position where the runout is the minimum.

b. If the runout value is still outside of the limit after the phase has been changed, possible cause will be an

assembly malfunction of drive pinion and pinion bearing and malfunction of pinion bearing. Check for

these items and repair if necessary.

c. If the runout value is still outside of the limit after the check and repair, replace companion flange.

Revision: 2006 November

RFD-43

2007 350Z

PDIA0491E SPD888 PDIA0069E

Revision: 2006 November

RFD-44

S-PD343
2007 350Z

REAR FINAL DRIVE ASSEMBLY
8. Lift differential case assembly out with a suitable tool.

q Keep side bearing outer races together with inner race. Do not mix them up. Also, keep side bearing adjusting washers together with bearings.

9. Remove side bearing inner race. To prevent damage to bearing, engage puller jaws in groove.

Tool number

A: ST33051001 (J-22888-20) B: ST33061000 (J-8107-2)

CAUTION: q To prevent damage to the side bearing and drive gear,
place copper plates between these parts and vise.
q It is not necessary to remove side bearing inner race except it is replaced.

Revision: 2006 November

RFD-45

PDIA0547E

RFD

G
SPD919
H

PDIA0639E

PDIA0496E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
13. Put matching marks with paint.

14. Loosen screws on differential cases A and B.

PDIA0640E

15. Separate differential case A and B, then remove viscous coupling, pinion mate gear, pinion mate thrust washer, side gear and side gear thrust washer from differential cases.
Drive Pinion Assembly 1. Remove differential assembly. Refer to RFD-44, "Differential Assembly" . 2. Remove drive pinion lock nut with the flange wrench.
Tool number : KV40104000 ( -- )

SDIA0189J PDIA0642E SDIA1144E

Revision: 2006 November

RFD-46

2007 350Z

Revision: 2006 November

RFD-47

PDIA0629E

RFD

G
SDIA1132E
H

I
J
SPD892
K
L

S-PD179

SDIA0817E
2007 350Z

REAR FINAL DRIVE ASSEMBLY

INSPECTION AFTER DISASSEMBLY
Clean up the disassembled parts. Then, inspect if the parts are worn or damaged. If so, follow the measures below.

Content
Hypoid gear
Bearing Side gear and Pinion mate gear Side gear thrust washer and pinion mate thrust washer
Oil seal

Differential case

q If any wear or crack on the contact sides of the differential case is found, replace.

Companion flange

q If any chipped mark (about 0.1 mm, 0.004 in) or other damage on the contact sides of the lips of the companion flange is found, replace.

ADJUSTMENT AND SELECTION OF ADJUSTING WASHERS Differential Side Gear Clearance q Assemble the differential parts if they are disassembled. Refer to RFD-44, "Differential Assembly" . 1. Place differential assembly so that right side gear is on the upper side. 2. Measure the clearance between right side gear back and differ-
ential case using feeler gauge, while rotating right side gear with a suitable tool attached to splines.
Side gear back clearance specification:
0.15 mm (0.0059 in) or less. (Each gear should rotate smoothly without excessive resistance during differential motion.)

CAUTION: q Do not place feeler gauge at groove side of differential
case.
q To prevent side gear from tilting, insert feeler gauges with the same thickness from both sides.

PDIA0641E

3. If the back clearance is outside the specification, use a thicker/thinner side gear thrust washer to adjust. Refer to RFD-60, "Side Gear Thrust Washer" .

When the back clearance is large:

Use a thicker thrust washer.

When the back clearance is small:

Use a thinner thrust washer.

CAUTION: q Adjust the clearance with the left side gear thrust washer only.
q Only one side gear thrust washer can be selected.

Revision: 2006 November

RFD-48

2007 350Z

REAR FINAL DRIVE ASSEMBLY

Side Bearing Preload

q Selecting carrier side bearing adjusting washers is required for successful completion of this procedure. A

1. Make sure all parts are clean. Also, make sure the bearings are

well lubricated with gear oil.

2. Place the differential case, with side bearings and bearing races

installed, into gear carrier.

3. Insert left and right original side bearing adjusting washers in place between side bearings and gear carrier.

SPD919

RFD E

4. Install bearing caps in their correct locations and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-55, "Differential Assembly" .
5. Turn the carrier several times to seat the bearings.

SPD924

K
PDIA0069E
L
M

SPD194A

Revision: 2006 November

RFD-49

2007 350Z

REAR FINAL DRIVE ASSEMBLY

7. If the turning torque is outside the specification, use a thicker/ thinner side bearing adjusting washer to adjust. Refer to RFD60, "Side Bearing Adjusting Washer" .

If the turning torque is less than the specified range: Use a thicker thrust washer.
If the turning torque is greater than the specification: Use a thinner thrust washer.

CAUTION:

Select a side bearing adjusting washer for right and left

individually.

SPD772

8. Record the total amount of washer thickness required for the correct carrier side bearing preload.

Pinion Gear Height 1. Make sure all parts are clean and that the bearings are well
lubricated.
2. Assemble the pinion gear bearings into the differential shim selector tool.

Tool number : -- (J-34309)

q Pinion front bearing; make sure the J-34309-3 pinion front bearing seat is secured tightly against the J-34309-2 gauge anvil. Then turn the pinion front bearing pilot, J-34309-5, to secure the bearing in its proper position.
q Pinion rear bearing; the pinion rear bearing pilot, J-34309-8, is used to center the pinion rear bearing only. The pinion rear bearing locking seat, J-34309-4, is used to lock the bearing to the assembly.
q Installation of J-34309-9 and J-34309-16; place a suitable 2.5 mm (0.098 in) thick plain washer between J-34309-9 and J-34309-16. Both surfaces of J-34309-9 and J-34309-16 must be parallel with a clearance of 2.5 mm (0.098 in).
3. Install the pinion rear bearing inner race into gear carrier. Then place the pinion preload shim selector tool, J-34309-1, gauge screw assembly.

SPD769 SPD197A

SPD893

Revision: 2006 November

RFD-50

2007 350Z

REAR FINAL DRIVE ASSEMBLY
4. Assemble the pinion front bearing inner race and the J-34309-2 gauge anvil. Assemble them together with the J-34309-1 gauge screw in gear carrier. Make sure that the pinion height gauge plate, J-34309-16, will turn a full 360 degrees. Tighten the two sections together by hand.
5. Turn the assembly several times to seat the bearings.

6. Measure the turning torque at the end of the J-34309-2 gauge anvil using preload gauge. Tool number : ST3127S000 (J-25765- A) Turning torque specification: 1.0 1.3 N·m (0.11 0.13 kg-m, 9 11 in-lb)
7. Place the J-34309-11 "R200A" pinion height adapter onto the gauge plate and tighten it by hand. CAUTION: Make sure all machined surfaces are clean.
8. Position the side bearing discs, J-25269-4, and arbor firmly into the side bearing bores. Install the bearing caps and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-39, "COMPONENTS" .

Revision: 2006 November

RFD-51

SPD199A

RFD

G
SPD770
H

I J

PDIA0566E

SPD208A

SPD211A
2007 350Z

REAR FINAL DRIVE ASSEMBLY
9. Select the correct standard pinion height adjusting washer thickness. Select by using a standard gauge of 3 mm (0.12 in) and your J-34309-101 feeler gauge. Measure the distance between the J-34309-11 pinion height adapter including the standard gauge and the arbor.
10. Write down exact measurement (the value of feeler gauge).

SPD204A

SPD775

Pinion head height number

Add or remove from the standard pinion height adjusting washer thickness measurement

SPD542

- 6

Add 0.06 mm (0.0024 in)

- 5

Add 0.05 mm (0.0020 in)

- 4

Add 0.04 mm (0.0016 in)

- 3

Add 0.03 mm (0.0012 in)

- 2

Add 0.02 mm (0.0008 in)

- 1

Add 0.01 mm (0.0004 in)

Use the selected washer thickness

Subtract 0.01 mm (0.0004 in)

Subtract 0.02 mm (0.0008 in)

Subtract 0.03 mm (0.0012 in)

Subtract 0.04 mm (0.0016 in)

Subtract 0.05 mm (0.0020 in)

Subtract 0.06 mm (0.0024 in)

12. Select the correct pinion height adjusting washer. Refer to RFD-60, "Pinion Height Adjusting Washer" .

Revision: 2006 November

RFD-52

2007 350Z

REAR FINAL DRIVE ASSEMBLY
13. Remove the J-34309 differential shim selector tool from the final drive housing. Then disassemble to retrieve the pinion bearings.

ASSEMBLY Drive Pinion Assembly 1. Install front and rear bearing outer races using drifts.

Tool number

A: ST30720000 (J-25405) B: KV40105230 ( -- )

C: ST30611000 (J-25742-1) D: ST30613000 (J-25742-3)

CAUTION: q At first, using a hammer, tap bearing outer race until it
becomes flat to gear carrier.
q Do not reuse pinion front and rear bearing outer race.
2. Select drive pinion height adjusting washer. Refer to RFD-50, "Pinion Gear Height" .

3. Install selected drive pinion height adjusting washer to drive pinion. Press pinion rear bearing inner race to it, using drift.
Tool number : ST30901000 (J-26010-01)
CAUTION: q Pay attention to the direction of pinion height adjusting
washer. (Assemble as shown in the figure.) q Do not reuse pinion rear bearing inner race.

SPD205A

RFD

G H

I J

K
PDIA0562E
L

SDIA0048E

Revision: 2006 November

RFD-53

2007 350Z

REAR FINAL DRIVE ASSEMBLY
4. Assemble collapsible spacer to drive pinion. CAUTION: Do not reuse collapsible spacer.
5. Apply gear oil to pinion rear bearing, and assemble drive pinion into gear carrier.
6. Apply gear oil to pinion front bearing, and assemble pinion front bearing inner race to drive pinion assembly. CAUTION: Do not reuse pinion front bearing inner race.
7. Using suitable spacer, press the pinion front bearing inner race to drive pinion as far as drive pinion nut can be tightened.
8. Using the drift, install front oil seal as shown in the figure. Tool number : ST30720000 (J-25405)
CAUTION: q Do not reuse oil seal. q When installing, do not incline oil seal. q Apply multi-purpose grease onto oil seal lips, and gear
oil onto the circumference of oil seal.
9. Install companion flange. NOTE: When reusing drive pinion, align the matching mark of drive pinion with the matching mark A of companion flange, then install companion flange.

PDIA0492E SPD896 PDIA0563E PDIA0629E

Revision: 2006 November

RFD-54

2007 350Z

REAR FINAL DRIVE ASSEMBLY

10. Apply anti-corrosion oil to the thread and seat of drive pinion

lock nut, and temporarily tighten drive pinion lock nut to drive

pinion.

CAUTION:

Do not reuse drive pinion lock nut.

11. Adjust to the drive pinion lock nut tightening torque and pinion

bearing preload torque.

Tool number A: KV40104000 ( -- )

B: ST3127S000 (J-25765-A)

Drive pinion lock nut tightening torque:

RFD

147 323 N·m (15 32 kg-m, 109 238 ft-lb)

Drive pinion bearing preload:

2.65 3.23 N·m (0.27 0.32 kg-m, 24 28 in-lb)

CAUTION:

q Adjust to the lower limit of the drive pinion lock nut tight-

ening torque first.

q If the preload torque exceeds the specified value, replace collapsible spacer and tighten it again to adjust. Do not loosen drive pinion lock nut to adjust the preload torque.

G
PDIA0636E

q After adjustment, rotate drive pinion back and forth 2 to 3 times to check for unusual noise, rota-

tion malfunction, and other malfunctions.

12. Install differential case assembly. Refer to RFD-44, "Differential Assembly" .

CAUTION:

Do not install rear cover yet.

13. Check and adjust drive gear runout, tooth contact, drive gear to drive pinion backlash, and companion

flange runout. Refer to RFD-40, "Drive Gear Runout" , RFD-41, "Tooth Contact" , RFD-42, "Backlash" and

RFD-43, "Companion Flange Runout" . Recheck above items. Readjust the above description, if necessary.

14. Check total preload torque. Refer to RFD-40, "Total Preload Torque" .

15. Install rear cover. Refer toRFD-44, "Differential Assembly" .

Differential Assembly

1. Install side gear thrust washer with the same thickness as the

ones installed prior to disassembly or reinstall the old ones on

the side gear.

SDIA0196J

Revision: 2006 November

RFD-55

2007 350Z

REAR FINAL DRIVE ASSEMBLY
2. Install side gear and thrust washer into differential case B. CAUTION: Make sure that the circular clip is installed to side gear.
3. Install pinion mate assembly (pinion mate shaft, pinion mate gears and pinion mate thrust washers) into differential case B. CAUTION: The pinion mate shaft groove side shall be installed to side gear.
4. Install viscous coupling into differential case B. 5. Install side gear thrust washer with the same thickness as the
ones installed prior to disassembly or reinstall the old ones on the viscous coupling.
6. Align the matching marks and install differential case A into differential case B.
7. Measure side gear end play. If necessary, select the appropriate side gear thrust washer. Refer to RFD-48, "Differential Side Gear Clearance" .
8. Align the matching mark of differential case with the mark of drive gear, then place drive gear.

SDIA0197J SDIA0198J PDIA0643E

9. Apply thread locking sealant into the thread hole of drive gear.
q Use Genuine High Strength Thread Locking Sealant or equivalent. Refer to GI-45, "Recommended Chemical Products and Sealants" .
CAUTION: Drive gear back and threaded holes shall be cleaned and degreased sufficiently.

Revision: 2006 November

RFD-56

SDIA2593E
SDIA2594E
2007 350Z

REAR FINAL DRIVE ASSEMBLY
10. Install drive gear on the mounting bolts, and then tighten to the specified torque. Refer to RFD-39, "COMPONENTS" . CAUTION: q Tighten bolts in a crisscross fashion. q After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.
11. Press side bearing inner races to differential case, using the drift and the base. Tool number A: KV38100300 (J-25523) B: ST33061000 (J-8107-2) CAUTION: Do not reuse side bearing inner race.
12. Install differential case assembly with side bearing outer races into gear carrier.
13. Measure side bearing preload. If necessary, select the appropriate side bearing adjusting washers. Refer to RFD-49, "Side Bearing Preload" .
14. Insert selected left and right side bearing adjusting washers in place between side bearings and gear carrier.

15. Align matching marks on bearing cap with that on gear carrier.
16. Install bearing caps and tighten bearing cap mounting bolts to the specified torque. Refer to RFD-39, "COMPONENTS" .

Revision: 2006 November

RFD-57

SDIA0247J

RFD

G
SPD353
H

I J

SPD919

SPD924

PDIA0069E
2007 350Z

REAR FINAL DRIVE ASSEMBLY

17. Using the drift, drive side oil seals until it becomes flush with the case end.
Tool number : KV38100200 (J-26233)

CAUTION: q Do not reuse oil seal.

q When installing, do not incline oil seal.

q Apply multi-purpose grease onto oil seal lips, and gear oil onto the circumference of oil seal.

18. Check and adjust drive gear runout, tooth contact, drive gear to

drive pinion backlash, and total preload torque. Refer to RFD-

SPD560

40, "Drive Gear Runout" , RFD-41, "Tooth Contact" , RFD-42,

"Backlash" and RFD-40, "Total Preload Torque" .

Recheck above items. Readjust the above description, if necessary.

19. Apply sealant to mating surface of rear cover.

q Use Genuine Silicone RTV or equivalent. Refer to GI-45, "Recommended Chemical Products and Sealants" .

CAUTION: Remove old sealant adhering to mounting surfaces. Also remove any moisture, oil, or foreign material adhering to application and mounting surfaces.

20. Install rear cover on gear carrier and tighten mounting bolts with the specified torque. Refer to RFD-39, "COMPONENTS" .

21. Install side flange with the following procedure. NOTE:

PDIA0961E

Install the RH side flange, then install the LH side flange. If LH side flange is installed first, the RH side

flange comes out sometimes from the shock of installing the RH side flange.

a. Attach the protector to side oil seal.

Tool number : KV38107900 (J-39352)

b. After the side flange is inserted and the serrated part of side gear has engaged the serrated part of flange, remove the protector.

c. Put a suitable drift on the center of side flange, then drive it until sound changes.
NOTE: When installation is completed, driving sound of the side flange turns into a sound which seems to affect the whole final drive.
d. Confirm that the dimension of the side flange installation (Measurement A) in the figure comes into the following.
Measurement A: 326 328 mm (12.83 12.91 in)

SDIA0822E PDIA0644E

Revision: 2006 November

RFD-58

2007 350Z

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) General Specifications

PFP:00030
A
NDS0000L

Applied model
Final drive model Gear ratio Number of teeth (Drive gear/Drive pinion) Oil capacity (Approx.) Number of pinion gears Drive pinion adjustment spacer type

(US pt, lmp pt)

R200 2

VQ35DE

M/T

A/T

R200V (With LSD)

3.538

3.357

46/13

47/14

1.4 (3, 2-1/2)

Collapsible

B C RFD

Inspection and Adjustment
DRIVE GEAR RUNOUT
Item
Drive gear back face

Runout limit 0.05 mm (0.0020 in) or less

NDS0000M

DIFFERENTIAL SIDE GEAR CLEARANCE

Specification

Item

R200

R200V (With LSD)

Side gear backlash (Clearance between side gear and differential case)

0.2 mm (0.008 in) or less

0.15 mm (0.0059 in) or less

(Each gear should rotate smoothly (Each gear should rotate smoothly

without excessive resistance during without excessive resistance during

differential motion.)

PRELOAD TORQUE

Item

Specification

Pinion bearing (P1 ) Side bearing (P2 )

2.65 3.23 N·m (0.27 0.32 kg-m, 24 28 in-lb)

0.20 0.52 N·m(0.02 0.05 kg-m, 2 4 in-lb)

Side bearing to pinion bearing (Total preload) (Total preload = P1 + P2 )

2.85 3.75 N·m(0.29 0.38 kg-m, 26 33 in-lb)
K

BACKLASH

Item Drive gear to drive pinion gear

Specification

0.10 0.15 mm (0.0039 0.0059 in)

COMPANION FLANGE RUNOUT
Item Companion flange face Inner side of the companion flange

M
Runout limit 0.08 mm (0.0031 in) or less 0.08 mm (0.0031 in) or less

Revision: 2006 November

RFD-59

2007 350Z

SERVICE DATA AND SPECIFICATIONS (SDS)

SELECTIVE PARTS Side Gear Thrust Washer

R200

Thickness

Part number*

0.75 (0.0295) 0.78 (0.0307) 0.81 (0.0319) 0.84 (0.0331) 0.87 (0.0343) 0.90 (0.0350) 0.93 (0.0366)

38424 EC000 38424 EC001 38424 EC002 38424 EC003 38424 EC004 38424 EC005 38424 EC006

Thickness
0.80 (0.0315) 0.83 (0.0327) 0.86 (0.0339) 0.89 (0.0350) 0.92 (0.0362) 0.95 (0.0374) 0.98 (0.0386) 1.01 (0.0398) 1.04 (0.0409) 1.07 (0.0421) 1.10 (0.0433) 1.13 (0.0445)

R200V

Part number*

Thickness

38424 40F60 38424 40F61 38424 40F62 38424 40F63 38424 40F64 38424 40F65 38424 40F66 38424 40F67 38424 40F68 38424 40F69 38424 40F70 38424 40F71

1.16 (0.0457) 1.19 (0.0469) 1.22 (0.0480) 1.25 (0.0492) 1.28 (0.0504) 1.31 (0.0516) 1.34 (0.0528) 1.37 (0.0539) 1.40 (0.0551) 1.43 (0.0563) 1.46 (0.0575) 1.49 (0.0587)

Unit: mm (in)
Part number*
38424 40F72 38424 40F73 38424 40F74 38424 40F75 38424 40F76 38424 40F77 38424 40F78 38424 40F79 38424 40F80 38424 40F81 38424 40F82 38424 40F83

*: Always check with the Parts Department for the latest parts information.

Pinion Height Adjusting Washer

Thickness
3.05 (0.1201) 3.08 (0.1213) 3.11 (0.1224) 3.14 (0.1236) 3.17 (0.1248) 3.20 (0.1260) 3.23 (0.1272) 3.26 (0.1283)

Part number*
38154 0C000 38154 0C001 38154 0C002 38154 0C003 38154 0C004 38154 0C005 38154 0C006 38154 0C007

R200, R200V

Thickness
3.29 (0.1295) 3.32 (0.1307) 3.35 (0.1319) 3.38 (0.1331) 3.41 (0.1343) 3.44 (0.1354) 3.47 (0.1366) 3.50(0.1378)

Unit: mm (in)
Part number*
38154 0C008 38154 0C009 38154 0C010 38154 0C011 38154 0C012 38154 0C013 38154 0C014 38154 0C015

*: Always check with the Parts Department for the latest parts information.

Side Bearing Adjusting Washer

Thickness
2.00 (0.0787) 2.05 (0.0807) 2.10 (0.0827) 2.15 (0.0846) 2.20 (0.0866) 2.25 (0.0886) 2.30 (0.0906)

Part number*
38453 N3100 38453 N3101 38453 N3102 38453 N3103 38453 N3104 38453 N3105 38453 N3106

R200, R200V

Thickness
2.35 (0.0925) 2.40 (0.0945) 2.45 (0.0965) 2.50 (0.0984) 2.55 (0.1004) 2.60 (0.1024) 2.65 (0.1043)

Unit: mm (in)
Part number*
38453 N3107 38453 N3108 38453 N3109 38453 N3110 38453 N3111 38453 N3112 38453 N3113

*: Always check with the Parts Department for the latest parts information.

Revision: 2006 November

RFD-60

2007 350Z

Acrobat Distiller 4.05 for Windows FrameMaker SGML 5.5.6p145J