Rohnson R-087 Genius Wi-Fi Digital Convector Heater

Introduction

Thank you for choosing the Rohnson R-087 Genius Wi-Fi digital convector panel heater. Please read this instruction manual carefully before use and keep it for future reference. Operate the appliance only as described in this manual.

Important Safety Instructions

Read Carefully and Keep for Future Use

• Failure to follow instructions may void the warranty. The manufacturer/importer is not liable for damages caused by non-compliance.
• Ensure your outlet voltage matches the appliance's rating. Use only grounded outlets.
• This appliance can be used by children aged 8 years and above, and by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they are supervised or have been instructed on safe use and understand the hazards. Cleaning and user maintenance must not be performed by children unsupervised. Keep the appliance and its power cord away from children under 8 years old.
• Do not allow children to play with the appliance.
• Use the appliance only for its intended purpose.
• Do not operate via external timers, programmers, or remote controls.
• Always switch off and unplug the appliance from the mains socket when not in use or before cleaning.
• Do not use if the appliance malfunctions, has been dropped, damaged, or immersed in water. Do not use with a damaged plug or cord. Do not attempt self-repair; contact an authorized service center. Do not modify the appliance to avoid electric shock risks.
• Do not unplug by pulling the power cord.
• Do not place heavy objects on the power cord. Ensure the cord does not hang over table edges or touch hot surfaces.
• Do not run the cord under carpets, rugs, or similar coverings. Position the cord away from traffic areas to prevent tripping hazards.
• This appliance is for household use only, not for outdoor, commercial, or industrial use.
• Do not use near bathtubs, showers, swimming pools, or containers of water. Do not operate while in a bath, shower, or pool.
• Use with the power cord fully extended.
• Operate only in an upright position.
• Do not use on soft surfaces or carpets with high pile.
• Place on a smooth, level, stable, and dry surface.
• Remove all packaging materials before use. Ensure the appliance is fully and correctly assembled before switching on.
• Check the appliance and power cord for damage before each use.
• Do not leave the appliance unattended while in operation.
• The appliance surface becomes hot during operation. Avoid burns by not touching hot surfaces. Position the appliance to prevent accidental contact with hot surfaces.
• Maintain at least 1 meter clearance from surrounding objects. Keep away from flammable materials.
• For wall mounting, ensure at least 15 cm clearance on all sides.
• Do not use in areas where flammable or explosive substances (e.g., petrol, paints) are used or stored.
• Do not plug high-power appliances into the same electrical circuit.
• Do not place the appliance directly under an electrical outlet.
• Before any manipulation, switch off, unplug from the mains, and let the appliance cool down.
• Always switch off the appliance before unplugging it from the mains.
• Never cover the appliance to prevent overheating.
• Do not insert any objects into the appliance. Air inlets and outlets must not be blocked.
• Do not use for drying laundry.
• Do not block the space between the appliance and the wall.
• Do not immerse the appliance or power cord in water or any liquid. Prevent direct contact with water and water ingress.
• Do not touch the appliance with wet hands.
• Regularly remove dust from air inlets and outlets using a vacuum cleaner.
• Do not use with an extension cord.
• Use only with supplied accessories.
• Keep packaging materials out of reach of children.
• Do not use in small rooms in the presence of immobile persons.
• The appliance has a safety fuse that will switch it off in case of overheating. If overheating occurs and the fuse activates, unplug the appliance and let it cool for 45 minutes before next use.
• Maximum radio-electrical power in the frequency bands where the radio equipment operates is 17.5 dBm at 2.400 ~ 2.4835 GHz.

Product Overview

Control Panel Description

The control panel includes:

• 1. Display: Shows current settings and temperature.
• 2. '+' Button: Increases temperature or value.
• 3. On/Off Button: Powers the appliance on or off.
• 4. Timer Button: Used for setting the timer functions.
• 5. '-' Button: Decreases temperature or value.
• 6. Mode Button: Selects operating modes (e.g., L, H, ECO, Weekly Timer, Open Window).

Remote Control Description

The remote control features:

• 1. On/Off Button: Powers the appliance on or off.
• 2. Mode Button: Selects operating modes.
• 3. Timer Button: Used for setting timer functions.
• 4. Open Window Mode Button: Activates the open window detection feature.
• 5. '+' Button: Increases temperature or value.
• 6. '-' Button: Decreases temperature or value.
• 7. Child Lock Button: Activates or deactivates the child lock feature.

Note: The functions of the remote control buttons correspond to the functions of the control panel buttons.

Installation

Freestanding Installation

Carefully place the appliance upside down on a soft surface (e.g., carpet). Attach the feet to the appliance using the provided screws. Push the wheels onto the attached feet. Turn the appliance upright and place it on its feet.

Wall Mounting Installation

Before wall mounting, ensure the installation area is free of electrical cables, water pipes, etc. Prepare the included mounting accessories. Position the appliance at a minimum distance of 15 cm from surrounding objects. Mount the heater bracket horizontally on the wall where you intend to place the appliance. Mark and drill holes for the bracket, then screw it to the wall, ensuring the screws protrude approximately 5 mm from the bracket. Align the holes on the rear of the appliance with the protruding screws and attach the appliance. The protective pads on the bottom of the appliance should rest against the wall. Ensure the appliance is securely and firmly mounted.

Using the Appliance

• Remove all packaging materials and stickers.
• Plug the appliance into the mains socket; it will enter standby mode.
• Press the On/Off button to turn the appliance on or off.
• The display shows the current room temperature.
• Default settings: Monday, 12:00, Low power (L), 20°C. Default weekly timer setting: Monday-Sunday, 00:00-24:00, 20°C.
• If the appliance is not connected to Wi-Fi, you must set the current time manually. (When connected to Wi-Fi, the current time is set automatically).
• During initial use, or after a long period of non-use, a slight odor may be noticeable. This is normal and will disappear soon. Ensure adequate ventilation.

Setting the Current Time

To set the current day of the week and time, select the weekly timer mode 'UP'. Use the '+' or '-' buttons to select the current day of the week (d1 – Sunday, d7 – Saturday). To set the hour, press the Timer button and then use '+' or '-' to set the current hour. To set the minutes, press the Timer button again and use '+' or '-' to set the minutes. Press the Timer button once more to confirm and save the settings.

Setting the Mode

Press the Mode button repeatedly to cycle through the available modes: L (Low Power), H (High Power), ECO, UP (Weekly Timer), and Open Window mode.

• L (Low Power): Heats at 1000W. Adjustable temperature.
• H (High Power): Heats at 2000W. Adjustable temperature.
• ECO: Heats at 2000W. For the first 2 minutes, it heats regardless of the set temperature; after 2 minutes, it continues heating according to the set temperature. If the room temperature is higher than or equal to the set temperature, heating will stop. If the temperature drops by 3°C below the set temperature, heating will resume.
• UP (Weekly Timer): Settings are made via the mobile application. The appliance will heat according to the settings in the app. If the weekly timer is not set in the app, the appliance will operate continuously at 20°C according to default settings.
• Open Window Mode: Displays the 'H' symbol for 3 seconds. If the appliance detects a temperature drop of 4°C within 30 minutes, it will automatically stop heating. If the temperature rises by 2°C within 30 minutes, heating will resume. Adjustable temperature is available in this mode.

Setting the Temperature

Press the '+' and '-' buttons repeatedly to set the desired temperature. An asterisk (*) on the display indicates that heating is active. Note: The temperature indicator deviation is ≤ 4°C.

Setting the Off Timer

To set the time after which the appliance will switch off, press the Timer button repeatedly. The setting range is 0-8 hours. The off timer function is available for L, H, and Open Window modes.

Setting the Weekly Timer (UP Mode)

The weekly timer allows you to set the heating on/off times and desired temperatures for each day of the week. This setting can only be done via the mobile application. When the weekly timer mode is selected, the appliance will heat according to the settings in the app. If the weekly timer is not set in the app, the appliance will operate according to the default settings, continuously at 20°C.

Special Functions

Child Lock Function

To activate/deactivate the child lock, press and hold the '+' or '-' button on the control panel for 3 seconds, or press the child lock button on the remote control. The On/Off button remains active; activating or deactivating the child lock does not cancel this function.

Wi-Fi Function

To activate the Wi-Fi function, press and hold the On/Off button for 3 seconds until you hear a beep and the Wi-Fi indicator starts blinking.

Display Dimming / Off

• If no setting is made for 60 seconds, the display brightness will automatically dim. Pressing any button will fully illuminate the display again.
• To turn off the display backlight, press and hold the '-' button and the Timer button simultaneously for 3 seconds while the appliance is in operation mode. Pressing any button will fully illuminate the display again.

Resetting the Appliance

To reset the appliance to factory settings, press and hold the Mode button and the '+' button simultaneously for 3 seconds during operation. The appliance will enter standby mode. After turning the appliance on with the On/Off button, the factory settings will be restored.

Error Codes

Cleaning and Maintenance

• Before cleaning, always switch off the appliance, unplug it from the mains, and let it cool down completely.
• Wipe the appliance surface with a damp cloth and let it dry.
• Remove accumulated dust from the appliance grilles using a vacuum cleaner.
• Do not use aggressive or abrasive cleaning agents.
• Do not immerse the appliance in water or any other liquid.
• Ensure the appliance is completely dry before plugging it back into the mains socket.
• Do not disassemble the appliance.
• If the appliance is not used for a long period, store it in its original packaging in a cool, dry place.

Mobile Application

The appliance can also be controlled via a smartphone mobile application.

• Download and install the Rohnson mobile application using the QR code, from Google Play, or the App Store (for operating system versions Android 5.0 and higher / iOS 11.0 and higher).
• Register using your email and log in.
• Enable Bluetooth on your mobile phone.
• Plug the appliance into the mains socket. For pairing, press and hold the On/Off button for 3 seconds until you hear a sound signal and the Wi-Fi indicator starts blinking. After successful connection to the network, a sound signal will be heard, and the Wi-Fi indicator will blink at 2-second intervals.
• Note: For initial pairing of devices with a local Wi-Fi network, it is recommended that both the appliance and the mobile phone are within 1 meter of the modem/router.
• To pair the appliance, tap '+' or 'Add device' in the application.
• Confirm that the Wi-Fi indicator is blinking rapidly and tap 'Next'.
• Select your Wi-Fi network and enter the password for that network. Tap 'Next'.
• Wait for the appliance to pair with the application. After successful pairing, the Wi-Fi indicator will light up, and the appliance can be controlled from the application's home screen.
• Note: If the appliance is disconnected from the mains after successful pairing, it will re-pair with the application upon reconnection and activation of the Wi-Fi function.

App Interface Description:

• The app displays screens for appliance status (e.g., 'Standby'), current temperature, set temperature, and controls for switching, mode selection, timer settings, and general settings.
• Key settings available via the app include: On/Off, Mode selection (H/L/ECO/Weekly Timer), Off Timer (1-8h), Child Lock, Weekly Timer setup (setting on/off times and temperatures for each day), and Open Window mode.

Wi-Fi Specifications and Manufacturer Information

Further Settings

Additional settings include changing the device name, viewing device information, and sharing the device with up to 20 users. To remove the device, press and hold the On/Off button for 3 seconds (your mobile phone must be paired with the device).

Wi-Fi Specifications

• Model: NMB20 / R-087
• Standard: 802.11 B/G/N20
• Antenna Type: Integrated in PCB
• WiFi Frequency: 2.400 ~ 2.4835 GHz
• Maximum Power: 17.5 dBm
• Dimensions: 16±0.35 mm (h) x 24±0.35 mm (d) x 0.8±0.1 mm (v)
• Operating Temperature: -20 °C - +85 °C
• Power Input: 3-3.6V DC

Manufacturer

Manufacturer: SHUNDE KINGTEC APPLIANCE CO.,LTD

Address: West of Fanghong Road, Xianlong Industrial Zone, Beijiao Shunde Foshan, Guangdong China, PC:528311

Tel: 0086-757-23272304

Simplified EU Declaration of Conformity

SHUNDE KINGTEC APPLIANCE CO.,LTD hereby declares that the radio equipment type R-087 complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.rohnson.eu

Technical Specifications and Disposal

Technical Specifications

Heat Output / Room Temperature Control Type

Other Control Options (Multiple selections possible)

Contact Information

ELECTRA TRADE, s.r.o.
Holečkova 440/15
150 00 Praha 5 – Smíchov
Czech Republic

Packaging and Disposal Information

Dispose of used packaging material at designated municipal waste disposal sites.

Disposal of Waste Electrical and Electronic Equipment: The symbol on the product or accompanying documents signifies that used electrical and electronic products must not be mixed with general household waste. For proper disposal, recovery, and recycling, return these products to designated collection points. Alternatively, in some EU or European countries, you may return your products to the local retailer when purchasing an equivalent new product. Proper disposal of this product helps conserve valuable natural resources and aids in preventing potential negative impacts on the environment and human health, which could result from improper waste disposal.

This product complies with all essential requirements of the relevant EU directives.

Note: This product is intended only for well-insulated spaces or for occasional use.