Instruction Manual for Tilvision models including: QL-G001 Fingerprint Door Lock, QL-G001, Fingerprint Door Lock, Door Lock, Lock
Tilvision Fingerprint Door Lock,Keyless Entry Touchscreen Keypad Deadbolt with Fingerprint,Fob & Passcode Unlock - Auto Lock & IP65 Waterproof - Biometric Security Door Lock for Front Door,Home,Office
File Info : application/pdf, 19 Pages, 4.17MB
DocumentDocumentSmart Lock Ref.: QL-G001 Instruction Manual TABLE OF CONTENTS 01 What's Included 10 Device settings 02 Name for parts 03 Prepare door before installation 04 How to install smart lock 14 How to use smart lock 16 Specifications It is very important to install and operate this product according to the following instructions. Failure to do so may render your guarantee void. 1. What's included Strike box Exterior assembly Interior assembly Mounting plate Strike plate Deadbolt Mechanical keys Key fob Long mounting plate screws Short mounting plate screw Interior assembly screw - 01 - Deadbolt / Strike screws 2. Name for parts 1 6 2 7 3 4 8 5 9 10 11 (1) Fingerprint scanner (4) Cylinder & Cylinder cover (7) Battery compartment (10) Type C port (2) Key fob reading area (5) Locked inside on / off (8) Thumbturn (11) Speaker (3) Keypad (6) Battery cover (9) Reset button - 02 - 3. Prepare Door before Installation 3.1. Make sure the following criteria are met so that the Smart Lock can be installed properly : · Check the door status, make sure the door frame is aligned with the door. · There are no obstructions stuck in the door frame. · Leave enough space for the deadbolt to extend into the door frame when the door is locked. 3.2. Check the door / frame dimensions to make sure they fit the following measurements before installation: · The cross bore diameter (2 '' / 54mm or 1 '' / 38mm) · Backset (2 '' / 60mm or 2 '' / 70mm) · Diameter of the door hole (1'' / 25mm). The door hole center and cross bore center should be aligned at the same horizontal level. · Door thickness (1 '' / 35mm - 2 '' / 55mm) Cross bore diameter 2 1 8" or 54mm or Cross bore diameter 1 1 2" or 38mm Backset 2 3 8"/ 60mm or 2 3 4"/ 70mm Door hole diameter 1" or 25 mm Door thickness 1 3 8"/ 35mm 2 1 8"/ 55mm - 03 - 3.3. If you already have an existing lock, please remove it including the deadbolt. 4. How to install smart lock Step 1: Install the Deadbolt 1. Measure your door's backset dimension: whether it is 2 3 4" / 70 mm or 2 3 8" / 60 mm. Backset 2 3 8"/ 60mm or 2 3 4"/ 70mm - 04 - 2. If your door's backset dimension is 2 3 8" / 60 mm, use the provided deadbolt to install. If your door's backset is 2 3 4" / 70 mm, turn the faceplate 180° and pull to extend simultaneously until the deadbolt locks in position as the illustration shows below. 180° 3. Insert the deadbolt into the doorframe and make sure the word "TOP" faces up as indicated on the deadbolt. 4. Screw into the doorframe with a screwdriver (not provided). Step 2: Install Strike Box and Strike Plate If you have an existing strike plate or strike box installed, skip this step. 1. Align the strike box with the center hole of the deadbolt. 2. Secure the strike box with strike plate and strike screws. Make sure it's placed in the correct direction. - 05 - Step 3: Install the Exterior Assembly 1. Route the cable connected on the exterior assembly under the deadbolt. 2. Keep the tailpiece in vertical position and insert it into the center hole of the deadbolt. - 06 - Step 4: Install the Mounting Plate 1. Route the cable through the mounting plate. 2. Fix the mounting plate onto the interior doorframe with the mounting plate screws. Make sure the long mounting plate screws go through the mounting plate and lock into the connecting pillars of the exterior assembly. Short mounting plate screw Long mounting plate screw - 07 - Step 5: Install the Interior Assembly 1. Check your existing door in the left or right and then turn the thumbturn in position as the illustration shows below. 2. Match the wire connector from the circuit board with the one from the exterior assembly as illustrated. The wire connector can only be plugged into the socket in one way. Make sure you match the dot on the connector with the pin on the circuit board correctly. 3. Secure the tailpiece with the key cylinder. Put the cable inside the cross bore as much as possible, otherwise its exposure will cause inconvenience to the interior assembly installation. - 08 - 4. Remove the battery cover. 5. Secure the provided screws into the interior assembly. 6. Turn the thumbturn to check whether the deadbolt is retracted. If the deadbolt does not work smoothly, adjust the screws and install the mounting plate again. 7. Install 4AA batteries with correct polarity and then close the battery cover. - 09 - 5. Device settings At factory default mode, press lock button ` ' to check if the locking direction is correct. If it's incorrect, press `888#' to switch the direction. Administrator setting At factory default mode, the initial administrator password is `123456' and it's a must to change it following up steps as shown below. Initial state * Press ` ' + `#' Enter `123456#' Press `1' for administrator settings Press `1' to add administrator Press `2' to delete administrator Register fingerprint and repeat by 4 times Input administrator no such as `002' + press '#' to confirm Set password with 6-8 digital numbers + press '#' to confirm and repeat by twice Administrator info you input will be deleted. * Press ` ' to return to last setting or exit 10s later Register key fob by once only Fingerprint / password / key fob will be saved as administrator no. such as 001 / 002... * Press ` ' to return to last setting or exit 10s later - 10 - User setting Initial state * Press ` ' + `#' Press `2' for user settings Enter `123456#' Press `1' to add user Register fingerprint and repeat by 4 times Press `2' to delete user Input user no such as `002' + press '#' to confirm Set password with 6-8 digital numbers + press '#' to confirm and repeat by twice User info you input will be deleted. * Press ` ' to return to last setting or exit 10s later Register key fob by once only Fingerprint / password / key fob will be saved as user no. such as 010/011... * Press ` ' to return to last setting or exit 10s later - 11 - System setting Initial state Press `1' to setup voice Press `2' to setup unlock mode Press `3' to setup select language Press `4' to setup date & time Press `5' to setup room number * Press ` ' + `#' Press `3' for system settings Press `1' to turn on voice Press `2' to turn off voice Press `1' to select single unlocking mode Press `2' to select combined unlocking mode. Then you have to use any two of fingerprint, key fob and password to unlock. Press `1' to select Chinese Press `2' to select English Input date & time 'YYYYMMDDHHMMSS' such as 202201011153 + press '#' to confirm Input room number such as 0001 + press '#' to confirm - 12 - Enter `123456#' Setting will be saved. * Press ` ' to return to last setting or exit 10s later * Press ` ' to return to last setting or exit 10s later * Press ` ' to return to last setting or exit 10s later * Press ` ' to return to last setting or exit 10s later * Press ` ' to return to last setting or exit 10s later Factory default setting Long press `Reset' at back door or follow the steps as below. Initial state * Press ` ' + `#' Enter `123456#' Press `4' to restore factory default settings Input administrator no. + press '#' to confirm * Press ` ' to return to last setting or exit 10s later - 13 - 6. How to use smart lock Unlock the door You can unlock the door using fingerprint, password, key fob, mobile app, or the provided key. Option 1: fingerprint Scan registered fingerprint and wait until the fingerprint breathing light breathes blue. Option 2: password Press any key or tap the touch panel to wake up the keypad and enter correct password to unlock the door. The system will be locked for 90 seconds if you have made more than five incorrect password attempts. Anti-peep password is to protect your privacy, which supports up to 20-digit vague code. Just enter any 20-digit code, as long as a correct code is included in what you entered, you can open the door. Example User Code: 123456 Vague Code 1: 1 2 3 4 5 6 X X X X X X 2: X X X X X X 1 2 3 4 5 6 3: X X X 1 2 3 4 5 6 X X X Option 3: key fob Swipe registered key fob on the reading field. Option 4: mechanical keys Open the cylinder cover and use the provided mechanical keys to unlock the door. - 14 - Lock the door At standby mode, press ` ' to lock the door directly. Low-power alert Smart lock will alert you automatically when low power. You are able to unlock the door up to 200 times since you get the first alert. Please replace the batteries asap. Locked inside on / off Locked inside on: Only administrators and mechanical keys are able to unlock the door, while users can't. Locked inside off: Both administrators and users are able to unlock the door. Auto-lock Input '555666777#' to enable Auto Lock and then the lock will relock automatically in 20s. Input '555666777#' again to disable Auto Lock. At factory default mode, it's enabled. Alarm setting Input '555666999#' to enable alarm and then the smart lock will sound loudly to scare the theft who wants to damage the smart lock and break in. Input '555666999#' again to disarm. At factory default mode, it's enabled. Reset · Long press `Reset' at back door using phone pin until hear one short beep, wait for around 6 seconds and then press `#' to confirm it. Or, · Refer to `Factory default setting' on keypad. - 15 - 7. Specifications · Power supply: 4 AA batteries or 5VDC charger in an emergency · Standby current: 50uA · Working current: 180mA · Administrator qty: Up to 10 · Fingerprint capacity: Up to 50 · Fingerprint + password + key fob capacity: Up to 250 · Numeric keypad: Touch buttons · Password length: 6-8 digital numbers · Anti-peep password length: Up to 20 digital numbers · Unlocking timing: 1s · Working environment: -25°C~60°C, 20%~90%RH · Material: Aluminium ally case + tempering panel · Size: 179mm x 73mm x 24mm (exterior) - 16 - SHENZHEN QIAOHUA INDUSTRIES LIMITED Add: Qiaohua Industrial Zone, LuoTian Forestry Center, Yan Luo, Bao An, Shenzhen, China 518127 Customer Support: support1@tilvision.com www.tilvision.com Made in China