Thank You
Thank you for purchasing this product. To achieve the perfect hidden-line effect, we use severely thin aviation-grade wire with high tension and pressure tolerance. However, due to its thin nature, be careful not to cut through it as it might be susceptible to shearing during installation. Always be careful not to press brick pieces down on the wire.
Let's Get Started
If you face any challenges, please feel free to reach out via support@gameofbricks.eu. Please note that we offer 2 years of free light kit maintenance.
Step 1 (Bag 1)
This step involves preparing and installing the initial components from Bag 1.
Image Description: The image displays two thin wires with small connectors, two small clear plastic pieces, and a sealed plastic bag labeled '1'.
Installation:
Action: A hand is shown inserting a thin wire with a small connector into a specific slot on the BWT Alpine F1 model chassis. An arrow [arrow pointing up] indicates the insertion direction.
Action: A hand is carefully routing a thin wire along the underside of the LEGO model, near the front wheel assembly. An arrow [arrow pointing left] indicates the path.
Action: A hand is attaching a small black component with a wire to the underside of the model, near the front. An arrow [arrow pointing right] indicates the connection point.
Action: A hand is inserting a thin wire into a small opening on the LEGO model's side. An arrow [arrow pointing down] indicates the placement.
Action: The underside of the LEGO model is shown with wires being routed and connected to specific brick elements. Arrows [multiple arrows] indicate connection points.
Action: A close-up shows a LEGO brick with a small pink connector piece and a wire being attached. An arrow [arrow pointing left] indicates the connection.
Action: The front underside of the model is shown with wires being positioned and secured. Arrows [multiple arrows] indicate the placement.
Action: The underside of the model is shown with multiple wires being routed and connected to various brick elements.
Step 2 (Bag 2)
This step focuses on installing the main LED strips from Bag 2.
Image Description: The image displays several thin LED strips with wires, and a sealed plastic bag labeled '2'.
Installation:
Action: A hand is shown attaching a component to the rear of the model. An arrow [arrow pointing up] indicates the insertion point.
Action: A hand is routing a wire from the rear of the model towards the side. An arrow [arrow pointing left] indicates the direction.
Action: A hand is holding an LED strip and positioning it along the side of the LEGO model. An arrow [arrow pointing down] indicates the placement.
Action: The underside of the model is shown with wires being routed and connected to specific brick elements. Arrows [multiple arrows] indicate connection points.
Action: A hand is connecting a wire to a small connector on the model's chassis. An arrow [arrow pointing right] indicates the connection.
Action: The front of the model is shown with wires being carefully positioned and routed. An arrow [arrow pointing left] indicates the path.
Action: The side of the model is shown with LED strips being attached and wires being routed underneath. An arrow [arrow pointing up] indicates the placement.
Action: The underside of the model is shown with wires being connected to brick elements.
Action: The side of the model is shown with LED strips installed and wires routed. An arrow [arrow pointing down] indicates the connection point.
Step 3
This step involves connecting the power source.
Image Description: The image displays a strip of small LED components, a USB connector cable with red and black wires, and the text 'Classic Version'.
Installation:
Action: A hand is shown connecting the LED strip to the USB power cable. Arrows [multiple arrows] indicate the connection points.
Action: The underside of the model is shown with the LED strip and power cable being connected to brick elements. Arrows [multiple arrows] indicate connection points.
Final Result: The completed LEGO model is shown with the light kit installed and illuminated with purple LEDs. [lightbulb icon] indicates the illuminated state.
Final Connection and Power
Connect the light kit to the battery box. Installation will be complete.
Important Note: If you would like to use another power source, please make sure the maximum voltage is 6V.
This completes the installation of your light kit.
Game of Bricks
