Heath Zenith Wireless Battery Doorbell Kit

Safety Information

WARNING: To prevent possible SERIOUS INJURY or DEATH, never allow small children near batteries. If a battery is swallowed, seek immediate medical attention.

WARNING: Do not dispose of batteries in fire. Batteries may explode or leak.

Package Contents and Specifications

• 1x Doorbell chime (requires 3 AA batteries - not included)
• 1x Doorbell button (requires CR2032 3V battery)
• 4x Screws
• 2x Wall anchors
• 1x Double-sided tape
• 1x CR2032 battery

Installation

1. Installing the Doorbell Chime Batteries

Push the battery cover tab toward the battery cover and pull to remove. Install 3 "AA" alkaline batteries (not included) into the doorbell chime. Ensure batteries are installed according to the diagram inside the chime. Replace the battery cover.

2. Installing the Battery to Doorbell Button

Rotate the battery cover and remove it. Insert the battery according to the figure, with the positive pole facing outward and the negative pole facing inward.

3. Testing the Doorbell Button and Doorbell Chime

Temporarily position the doorbell button and chime where they will be mounted. Press the doorbell button to verify they work. If the chime does not sound, move the chime closer to the button and test again. Do not permanently mount until working correctly.

Note: The doorbell button and chime come factory-synced. Range can vary. Test before permanent mounting.

4. Mounting the Doorbell Button

Use either screws or double-sided tape. For screws: remove the back cover by pushing the tab with a small screwdriver, place the button on the door jamb, mark screw holes, attach with screws, and snap on the front. For tape: remove paper from both sides of the tape and apply to a clean surface.

5. Mounting the Doorbell Chime

Use two screws to mount the chime. Determine location, drill two 7/32 in. (5.5 mm) pilot holes, insert wall anchors. Insert screws into anchors leaving about 1/8 in. (3.2 mm) exposed. Hang the chime on the screws using the keyhole on the back.

Operation

1. Adjusting the Doorbell Chime Volume

The chime has an adjustable volume control on the side. Press and release the volume adjust button to change volume.

2. Muting the Doorbell Chime

Press and release the "Tune" and "Volume" buttons simultaneously. The light will flash 4 times with no sound, indicating mute. Press "Volume" or "Tune" to unmute.

3. Selecting a Tune

The chime has ten pre-loaded tunes. Press and release the "Tune" button until the desired tune is heard. Press the doorbell button while the tune is playing to lock it. Each button can have a unique tune.

Selectable Tunes:

• Auld Lang Syne
• Beethoven's 5th
• Birthday Celebration
• Ding-Dong
• Relax Triplet
• Shorty
• We wish you a merry Christmas
• Short Westminster
• Westminster
• Huntington

4. Selecting the Doorbell Chime Light

The chime has 8 selectable light colors. Press and release the "Light" button to select a color. When the doorbell button is pressed, the chime rings and the light flashes 4 times.

Code Conversion and Low Battery Notification

Doorbell Button Code Conversion

Default code pattern is 100M. To convert to 12E, press the silicone button on the back for 3 seconds; the indicator light will flash quickly once. To convert back to 100M, press the silicone button for 3 seconds; the indicator light will flash for 3 seconds. Codes must match for proper operation.

Doorbell Chime Code Conversion

Default code pattern is 100M. To convert to 12E: after power-on, the chime prompts "Ding" (100M). Within one minute, press and hold "Volume" and "Tune" buttons for 10 seconds until "beep-beep", then release; chime will prompt "Ding-Dong" (12E). To convert to 100M: chime prompts "Ding-Dong" (12E). Within one minute, press and hold "Volume" and "Tune" for 10 seconds until "beep-beep", then release; chime will prompt "Ding" (100M). Codes must match for proper operation. Re-syncing may be needed after conversion.

Low Battery Notification

Doorbell Button: After pressing the button, the chime prompts "Ding-Dong" 3 times and the indicator light stays on for 10 seconds, indicating low battery in the button.

Doorbell Chime: After pressing the button, the chime prompts "Ding-Dong" 5 times and the indicator light flashes quickly for 10 seconds, indicating low battery in the chime.

Troubleshooting

Problem #1: The doorbell chime does not sound.

Possible Causes: Batteries not installed correctly, dead batteries, button/chime not synced, mismatched codes.

Solutions: Check battery installation, check battery charge, sync button/chime (press "Tune" on chime until "beep-beep", press button within 10 seconds), ensure codes match.

Problem #2: Chime does not work after installation (batteries okay).

Possible Causes: Mounted on metal or near metal studs, near concrete, too far apart.

Solutions: Use wood shims to move away from metal, move away from concrete, move chime closer to button.

Problem #3: Doorbell chime sounds when not intended (false triggers).

Possible Causes: Interference from other wireless devices.

Solutions: Convert to 100M code. If in 12E code: remove button battery, wait 30s, press and hold button for 10-15s within 60s of re-inserting battery. On chime, press and hold "Tune" until "beep-beep-beep-beep". Re-sync by pressing and holding "Tune" until "beep-beep", then press button within 10s.

Problem #4: New button/chime do not work with existing ones.

Possible Causes: Mismatched codes.

Solutions: Ensure codes match (both 100M or both 12E). Call 1-888-543-1388 for assistance.

1-Year Limited Warranty

Product guaranteed free of factory defects for 1 year from purchase date. Purchase receipt required. Warranty excludes expendable items (batteries, bulbs), misuse, abuse, unauthorized service, inconvenience, etc. Contact Heath Zenith for details.

FCC Statement

This device complies with Part 15 of FCC Rules. Operation is subject to two conditions: no harmful interference, and acceptance of any interference. Changes not approved by the responsible party may void user authority. Tested and found to comply with Class B digital device limits. Generates radio frequency energy; may cause interference if not installed per instructions. User encouraged to correct interference by reorienting antenna, increasing separation, connecting to a different circuit, or consulting a dealer/technician.

Contains licence-exempt transmitter(s)/receiver(s) complying with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation subject to: 1. No interference. 2. Acceptance of any interference.

CAN ICES-3(B)/NMB-3(B)

FCC Responsible Party: Globe Electric, 2264 East 6th Street, San Bernardino, CA 92410, www.globe-electric.com