MSI PRO Series LCD Monitor User Manual

Aan de slag (Getting Started)

This chapter provides information on hardware setup procedures. Exercise caution when handling devices and use a grounded wrist strap to prevent static electricity.

Inhoud verpakking (Package Contents)

? Belangrijk (Important)

• Contact your point of purchase or local distributor if any items are damaged or missing.
• Package contents may vary by country.
• The included power cord is for this monitor only and should not be used with other products.

De monitorstandaard installeren (Installing the Monitor Stand)

? Belangrijk (Important)

• Place the monitor on a soft, protected surface to avoid scratching the display panel.
• Do not use sharp objects on the panel.
• This product is supplied WITHOUT a protective film for the user to remove! Any mechanical damage to the product, including removal of the polarizing film, may affect the warranty!

PRO MP242A/ PRO MP271A

1. Leave the monitor in its protective foam packaging. Align the stand with the monitor groove. Push the stand towards the monitor groove until it locks into place.

2. Attach the base to the stand and tighten the base screw to secure the base.

3. Ensure the stand assembly is properly installed before setting the monitor upright.

Diagram Description: A diagram shows the monitor in protective packaging. An arrow indicates aligning the stand with the monitor groove. A close-up shows the base being attached to the stand with a screw.

PRO MP242AP/ PRO MP271AP

1. Leave the monitor in its protective foam packaging. Align the stand bracket with the monitor groove.

2. Secure the stand bracket with screws.

3. Attach the base to the stand and tighten the base screw to secure the base.

4. Ensure the stand assembly is properly installed before setting the monitor upright.

Diagram Description: A diagram shows the monitor's rear bracket being secured with screws (labeled 1, 2) and the base being attached to the stand with a screw (labeled 3).

? Belangrijk (Important)

The groove for installing the stand bracket can also be used for wall mounting. Contact your dealer for the correct wall mount kit.

De monitor aanpassen (Adjusting the Monitor)

This monitor is designed to maximize your viewing comfort with its adjustment capabilities.

? Belangrijk (Important)

• Avoid touching the display panel when adjusting the monitor.
• Slightly tilt the monitor backward before adjusting the hinges.

PRO MP242A/ PRO MP271A

Diagram Description: A side view of the monitor stand shows the tilt adjustment range from -5° to 23°.

PRO MP242AP/ PRO MP271AP

Diagram Description: Multiple views illustrate adjustment capabilities: tilt (-8° to 20°), swivel (30° left/right), and height adjustment (120mm).

Monitoroverzicht (Monitor Overview)

Diagram Description: A front view of the monitor displays numbered connection ports and buttons on the rear/bottom.

De monitor aansluiten op pc (Connecting the Monitor to a PC)

1. Turn off your computer.
2. Connect the video cable from the monitor to your computer.
3. Connect the power cord to the monitor's power input. (Diagram A)
4. Connect the power cord to the wall outlet. (Diagram B)
5. Turn on the monitor. (Diagram C)
6. Turn on the computer; the monitor will automatically detect the signal source.

Diagram Description: Illustrates the connection process: (C) Hand pressing power button, (A) Video cable connecting monitor and PC, (B) Power cable connecting monitor to wall outlet.

OSD-instelling (OSD Setup)

This chapter contains important information about OSD setup.

? Belangrijk (Important)

All information is subject to change without prior notice.

OSD-toetsen (OSD Keys)

The monitor comes with a set of OSD keys to help operate the On-Screen Display (OSD) menu.

Diagram Description: A diagram shows the OSD buttons numbered 1-4 with corresponding symbols (+, -, MENU/ENTER, AUTO/SOURCE/EXIT).

Het Menu's OSD (The OSD Menu)

Luminance (Luminantie)

PRO MP242A, PRO MP242AP

Diagram Description: Shows the Luminance OSD screen with Contrast, Brightness, Eco Mode, and DCR settings.

PRO MP271A, PRO MP271AP

Diagram Description: Shows the Luminance OSD screen with Contrast, Brightness, Eco Mode, Eco Friendly, and DCR settings.

Image Setup (Beeldinstelling)

Color Temp. (Kleurtemperatuur)

OSD Setup (OSD-instelling)

Extra (Extra)

Specificaties (Specifications)

* Gebaseerd op CIE1976-testnormen. (Based on CIE1976 test standards.)

Vooraf ingestelde weergavemodi (Preset Display Modes)

? Belangrijk (Important)

All information is subject to change without prior notice.

Problemen oplossen (Troubleshooting)

De Aan/Uit-LED is uit. (The Power LED is off.)

• Press the monitor's power button again.
• Check if the monitor's power cord is properly connected.

Geen afbeelding. (No Picture.)

• Check if the computer's graphics card is installed correctly.
• Ensure the computer and monitor are connected to power outlets and are turned on.
• Check if the monitor's signal cable is properly connected.
• The computer may be in standby mode. Press a key to activate the monitor.

De schermafbeelding heeft geen juiste grootte of is niet juist gecentreerd. (The screen image is not the correct size or is not centered.)

• Refer to the preset display modes to set the computer to a suitable display setting for the monitor.

Geen Plug & Play. (No Plug & Play.)

• Check if the monitor's power cord is properly connected.
• Check if the monitor's signal cable is properly connected.
• Ensure the computer and graphics card are compatible with Plug & Play.

De pictogrammen, het lettertype of het scherm is wazig, onscherp of heeft kleurproblemen. (Icons, font, or screen is blurry, out of focus, or has color problems.)

• Avoid using video extension cables.
• Adjust brightness and contrast.
• Adjust RGB color or color temperature.
• Check if the monitor's signal cable is properly connected.
• Check for bent pins on the signal cable connector.

De monitor begint te flikkeren of toont golven. (The monitor starts flickering or shows waves.)

• Change the refresh rate to match your monitor's capabilities.
• Update your graphics card drivers.
• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).

Veiligheidsrichtlijnen (Safety Guidelines)

• Read the safety guidelines carefully and thoroughly.
• Pay attention to all warnings on the device or in the user manual.
• Refer servicing to qualified personnel only.

Voeding (Power)

• Ensure the power voltage is within a safe range and correctly adjusted to the 100~240V value before connecting the device to the outlet.
• If the power cord is supplied with a 3-pin plug, do not disable the protective earth pin on the plug. The device must be connected to an earthed outlet.
• Confirm that the power distribution system at the installation location provides a circuit breaker with a specification of 120/240V, 20A (maximum).
• Always disconnect the power cord or turn off the wall socket if the device remains unused for a period to achieve zero energy consumption.
• Place the power cord so that no one can step on it. Do not place objects on the power cord.
• If this device is supplied with an adapter, use only the MSI-provided adapter approved for use with this device.

Omgeving (Environment)

• To reduce the risk of heat-related injury or overheating of the device, do not place it on a soft, unstable surface and do not obstruct the air vents.
• Use this device only on a hard, flat, and stable surface.
• To prevent the device from tipping over, secure it to a desk, wall, or fixed object with an anti-tip device that helps support the device and keep it safely in place.
• To prevent the risk of fire or electric shock, keep this device away from humidity and high temperatures.
• Do not leave the device in an unsuitable environment with a storage temperature above 60°C or below -20°C, as it may cause damage.
• The maximum operating temperature is approximately 40°C.
• When cleaning the device, ensure you unplug it from the power outlet. Use a soft cloth instead of industrial chemicals to clean the device. Never pour liquids into any opening, as this may cause damage to the device or an electric shock.
• Always keep strongly magnetic or electrical objects away from the device.

Situations requiring service:

• If any of the following situations occur, have the device checked by service personnel:
• The power cord or plug is damaged.
• Liquid has entered the device.
• The device has been exposed to moisture.
• The device is not functioning properly or cannot be made to work according to the user manual.
• The device has been dropped and damaged.
• The device shows obvious signs of breakage.

Certificeringen (Certifications)

TÜV Rheinland-certificering voor Low Blue Light (weinig blauw licht)

Blue light has been shown to lead to eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland certification for low blue light to ensure eye comfort and user well-being. Follow the instructions below to reduce symptoms of prolonged exposure to the screen and blue light:

• Position the screen 20 – 28 inches (50 – 70 cm) from your eyes and slightly below eye level.
• Periodically blinking your eyes consciously helps reduce eye fatigue after prolonged screen viewing.
• Take a 20-minute break every 2 hours.
• Look away from the screen and stare at a distant object for at least 20 seconds during breaks.
• Perform stretching exercises to relieve body fatigue or pain during breaks.
• Enable the optional Low Blue Light function.

TÜV Rheinland-certificering voor Flicker Free (flikkervrij)

TÜV Rheinland has tested this product to determine if the screen produces visible or invisible flicker for the human eye, causing user eye fatigue.

TÜV Rheinland has defined a catalog of tests, describing minimum standards across various frequency ranges. The test catalog is based on internationally applicable standards or widely used industry standards and exceeds these requirements.

The product has been tested in the laboratory according to these criteria.

The term "Flicker Free" confirms that the device has no visible or invisible flicker as defined in this standard within the range of 0 - 3000 Hz under various brightness settings.

The screen does not support Flicker Free when Anti-blur, de-blur, or MPRT is enabled. (The availability of Anti-blur, de-blur, or MPRT varies by product.)

ENERGY STAR-certificering

ENERGY STAR is a program run by the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) to promote energy efficiency. This product qualifies for ENERGY STAR in its standard factory settings, achieving energy savings. Changing the standard factory settings or enabling other functions will increase energy consumption, which may exceed the limits required to qualify for an ENERGY STAR rating.

For more information about ENERGY STAR, please refer to https://www.energystar.gov/.

Regelgevingsberichten (Regulatory Information)

CE-conformiteit

This device complies with the requirements set forth in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low Voltage Directive (2014/35/EU), ErP Directive (2009/125/EG), and RoHS Directive (2011/65/EU). This product has been tested and found to be in compliance with the harmonized standards for IT equipment published under the Official Journal of the European Union Directives.

FCC-verklaring Klasse B radiofrequentiestoringen (FCC Declaration Class B Radio Frequency Interference)

This device has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy which, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, no guarantee can be given that interference will not occur in a specific installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device on and off, the user should try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the supplier or an experienced radio/TV technician for help.

Melding 1 (Notice 1)

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Melding 2 (Notice 2)

To comply with emission limits, shielded interface cables and a power cord must be used.

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

WEEE-verklaring (WEEE Declaration)

According to Directive 2012/19/EU of the European Union ("EU") on waste of electrical and electronic equipment, products of "electrical and electronic equipment" may no longer be disposed of with household waste, and manufacturers of covered electronic equipment are obliged to take back such products at the end of their useful life.

Informatie over chemische bestanddelen (Chemical Substance Information)

In compliance with regulations concerning chemical substances, such as the EU REACH Regulation (EC Regulation No. 1907/2006 of the European Parliament and of the Council), you can find MSI's information on chemical substances at https://csr.msi.com/global/index.

Eigenschappen groen product (Green Product Features)

• Reduced energy consumption during use and standby.
• Limited use of substances harmful to the environment and health.
• Easy disassembly and recycling.
• Reduced use of natural resources by promoting recycling.
• Longer product lifespan through easy upgrades.
• Less solid waste production through take-back policy.

Milieubeleid (Environmental Policy)

• The product is designed to facilitate the reuse of components and recycling, and should not be disposed of at the end of its life.
• Users should contact their local authorized collection point for recycling and disposal of products at the end of their lifespan.
• Visit the MSI website and find a dealer near you for more information on recycling.
• Users can also reach us at gpcontdev@msi.com for information regarding the disposal, return, recycling, and dismantling of MSI products.

Waarschuwing (Warning)

Excessive use of screens may affect vision.

Aanbevelingen (Recommendations):

1. Take a 10-minute break every 30 minutes of screen work.
2. Children under 2 years of age should not be allowed to look at the screen. For children aged 2 years and older, screen time should be limited to less than one hour per day.

Verklaring van copyright en handelsmerken (Copyright and Trademark Statement)

Copyright © Micro-Star Int'l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int'l Co., Ltd. All other brands and names mentioned may be trademarks of their respective owners. There is no express or implied warranty regarding accuracy or completeness. MSI reserves the right to make changes to this document without prior notice.

The terms HDMITM, HDMITM High-Definition Multimedia Interface, HDMITM Trade dress, and the HDMITM logos are trademarks or registered trademarks of HDMI™™ Licensing Administrator, Inc.

Technische ondersteuning (Technical Support)

If a problem occurs with your product and you cannot find the solution in the user manual, please contact the point of sale where you purchased the product or a local distributor. Otherwise, visit https://www.msi.com/support/ for further guidance.