CUMMINS jetscan Quick Reference Manual - User Manual - PDF Download
Quick Reference for JetScanTM
Daily Cleaning Procedures Pages 3-8 Stopping Conditions & Recovery Steps Pages 9-20
852 Feehanville Drive Mt. Prospect, IL 60056 Telephone: (847) 299-9550 Fax: (847) 759-3091
© 2009 CUMMINS-ALLISON CORP. ALL RIGHTS RESERVED. PRINTED IN USA
Factory Part 022-7271-00 Field Form 023-1644-00 Rev. F 11/2009
Quick Reference for JetScanTM
Hopper
Feed roller Display Function keys
Stacker wheels Stacker
Machine Diagram
Thickness adjustment dial
Hopper guides
Feed roller Feeder plate
Function keys Power switch and power cord on rear of unit
Stacker sensor
Stacker mirror
Daily Cleaning Procedures
Daily cleaning of the JetScanTM currency scanner is recommended to ensure maximum productivity and reliability, especially for high-volume applications, as well as for those processing highly circulated (dirty) currency.
Follow these steps, which only will take a few minutes.
Recommended Cleaning Materials
Simple Green®, the recommended cleaning agent, can be an eye irritant. Avoid eye contact. If eye contact occurs, flush eye(s) with cool water for 5 minutes remove contact lenses if present continue flushing eye(s) with cool water for 15 more minutes. If irritation persists, consult physician. Individuals with sensitive skin should rinse hands after using.
· Simple Green® Safety Towels*. (Part number: 022-2118-00.) A pre-moistened towelette or pre-moistened microfiber towel also may be used. If using Simple Green® concentrate, dilute to: 1 ounce of Simple Green® per 8 ounces of water.
· Microfiber towels. (Part number: 022-2223-00.) · A clean, soft eraser. (Part number: 022-1695-00.) · Vacuum. (Part number for standard vacuum: 022-1959-00; part number
for heavy-duty vacuum: 022-1308-00.)
* Simple Green® is a registered trademark of Sunshine Makers Inc. For a material-safety-data sheet, see www.SimpleGreen.com.
Daily Cleaning
2
D A I LY
CLEANING
JetScanTM
High voltage inside. Risk of electric shock. Turn power OFF and unplug power cord from machine before cleaning.
JetScanTM
D A I LY
CLEANING
3
To avoid machine/component damage and potential voiding of existing warranty, follow these procedures:
Only use specified tools for cleaning machine. Never use metal tools.
If using Simple Green® concentrate, dilute to: 1 ounce of Simple Green® per 8 ounces of water.
Never use cleaners containing ammonia. Ammonia may remove labels from machine.
Never spray cleaners directly on machine components.
1
Turn power OFF (rocker panel to 0).
2
Disconnect power cord from the rear of the JetScan.
3 Remove hopper extension.
4
Remove feeder plate as shown at left.
5
Use a microfiber towel to clean the black start sensor at the top,
middle of the feeder plate.
Start sensor
6
Use a Simple Green® Safety Towel to remove dirt buildup from
the upper and lower aluminum rollers.
To reach all exposed surfaces, rotate
the large, black feed rollers forward
(direction of note flow). (See Helpful
Hint below.)
If there is heavy buildup on the aluminum rollers, remove it with a clean, soft eraser as shown.
Helpful Hint: Rotating the large, black feed rollers will rotate
all other shafts and rollers in the machine. These rollers can be rotated in either direction by using fingers. Generally, the top of these rollers should be rotated forward (direction of note flow), so any dirt or stray material is moved out of the unit.
Center rubberdrive tire
4
D A I LY
CLEANING
JetScanTM
JetScanTM
Black feed rollers
D A I LY
CLEANING
5
7
Use a Simple Green® Safety Towel to clean all rubber sections of the large, black
feed rollers. Rotate the rollers.
Also clean the flat, center rubber-drive tire.
Flat, center rubber-drive tire
8
Use a microfiber towel or vacuum to remove any remaining dust in
the bottom stacker.
11
Clean exterior surfaces as necessary a Simple Green® Safety Towel.
with
12 Replace hopper extension.
9
Use a microfiber towel to clean the stackersensor lens located in the stacker tray
between the two gray stacker wheels.
Clean the stacker mirror located directly across from the stacker-sensor lens.
Stacker-sensor lens Stacker mirror
10
Replace feeder plate. Insert curved edge of feeder plate first. Gently press down
on feeder plate until it snaps into position.
Curved edge
13 Carefully reconnect power cord. 14 Turn power ON (rocker panel to I). 15 Perform a test run with some currency.
6
D A I LY
CLEANING
JetScanTM
JetScanTM
D A I LY
CLEANING
7
Cleaning Supplies
The following items are available for purchase through
Cummins-Allison Corp.
Desktop-Currency-Equipment Cleaning Kit (Part Number: 406-1000-01.) The kit contains: · 2 stick erasers · 20 microfiber towels · 50 Simple Green® Safety Towels · Quick-reference guides
Items Sold Separately · 1 stick eraser. (Part number: 022-1695-00.) · 20 microfiber towels. (Part number: 022-2223-00.) · 50 Simple Green® Safety Towels. (Part number: 022-2118-00.) · Vacuum. (Part number for standard vacuum: 022-1959-00;
part number for heavy-duty vacuum: 022-1308-00.)
Power-Adapter Cable (Part Number: 022-1962-00.) This cable allows the power cord that is disconnected from the rear of the JetScan to be used to power the vacuum.
How to Order
To place an order in the United States, please call 1-800-745-9483, visit www.CumminsSupplies.com, or contact your local Cummins representative.
To place an order outside of the United States, contact your local Cummins representative.
8
D A I LY
CLEANING
JetScanTM
Quick Reference for JetScanTM
Stopping Conditions and Recovery Steps
In operation, the JetScan currency scanner display will advise users of conditions that have caused the machine to stop. These stopping conditions require attention.
Stopping-condition displays are shown in alphabetical order on the following pages, along with brief explanations and steps that should be taken to continue operation. A sample is shown below.
Explanation
Display
(Listed alphabetically)
D I S P L AY
JetScan may have processed two or more notes as one.
SAMPLE ± Remove all notes from the bottom stacker and place them on the top hopper. Press Cont. If an alarm repeatedly occurs, adjust the gray thickness dial located on top of the machine behind the hopper. Rotate in the negative (-) direction as indicated by numbers on front of the thickness dial.
Necessary steps to continue operation
JetScanTM
STOPPING CONDITIONS & RECOVERY
9
Hopper
Feed roller Display Function keys
Stacker wheels Stacker
Machine Diagram
Thickness adjustment dial
Hopper guides
Feed roller Feeder plate
Function keys Power switch and power cord on rear of unit
Stacker sensor
Stacker mirror
Display
Cont Clear key key
Denomination value keys
10
STOPPING CONDITIONS & RECOVERY
JetScanTM
Stopping Conditions and Recovery Steps
Screens Listed Alphabetically
D I S P L AY JetScan may have processed two or more notes as one.
± Remove all notes from the bottom stacker and place them on the top hop-
per. Press Cont. If an alarm repeatedly occurs, adjust the gray thickness dial located on top of the machine behind the hopper extension. Rotate in the negative (-) direction as indicated by the numbers on the front of the thickness dial.
D I S P L AY
JetScan has identified a note that is different than those it has been processing while using sort mode.
This first note of the different denomination is the top note in the lower stacker.
± Remove all notes from the bottom stacker. Separate the top note from the
remaining notes. Put the top note in the location for its denomination. Put all the other notes (they are all the same) in the location for their denomination.
JetScan automatically will restart.
D I S P L AY
JetScan may have processed two or more notes as one.
± Remove all notes from the bottom stacker and put them on the top hopper.
Press Cont. If an alarm repeatedly occurs, adjust the gray thickness dial on top of the machine behind the hopper extension. Rotate in the negative (-) direction as indicated by the numbers on the front of the thickness dial.
JetScanTM
STOPPING CONDITIONS & RECOVERY
11
D I S P L AY JetScan has identified a note that is incorrectly faced.
± Users should either:
· Face the note, replace it in the bottom stacker, and press the appropriate denomination value key.
· Correctly face the note, return it to the top hopper, and press Cont.
D I S P L AY Currency or possibly foreign material is jammed in the paper path and must be removed.
Do not use tools or metal devices to remove jammed currency from paper path. Use of tools or metal devices could cause machine damage and void existing warranty. For proper removal of jammed currency, see step No. 2 on Page 13.
12
STOPPING CONDITIONS & RECOVERY
JetScanTM
1
± Remove all notes from
the top hopper and bottom stacker.
Remove the hopper extension, as shown in inset.
Remove the feeder plate, as shown at right.
Remove feeder plate by lifting with fingers in the two depressions.
When notes are removed from the bottom stacker, the display will show:
JetScanTM
2
± Raise the two red, plastic "T"
handles at the same time and hook them onto the metal shaft. Then either:
· Move jammed notes forward/ back by manually rotating the large, black feed rollers. (See Helpful Hint on Page 5.)
· Press Clear to slowly move the feeder forward.
· Press Strap to slowly move the feeder in reverse.
Remove all jammed notes and foreign material.
STOPPING CONDITIONS & RECOVERY
13
3
Unhook the two red, plastic "T" handles from the metal
shaft and lower them at the
same time.
4
Replace feeder plate. Insert curved edge of feeder plate
first. Gently press down on feeder
plate until it snaps into position.
Curved edge
5
Replace the hopper extension.
Press Cont.
Rerun all notes that were in the top hopper and bottom stacker at the time of the jam.
These two screens will sequentially flash:
This screen could show any of these messages: · NO CALL · NO CALL SKEW · NO CALL* · NO CALL** · NO CALL***
D I S P L AY
JetScan cannot recognize the denomination of a note and has stopped. This "NO CALL" note is the top note in the bottom stacker. This note has not been included in the count.
± Inspect the top note in the bottom stacker. DO NOT remove all notes
from the bottom stacker.
To count the note, keep the note in the bottom stacker and then enter its denomination using the correct denomination value key ($1, $5, $10, etc.). JetScan will start, and this note will be added to the count.
To not count the note, remove it and press Cont. JetScan will re-start. The removed document WILL NOT be added to the count.
If the note is not mutilated, it may be returned to the top hopper for reprocessing.
D I S P L AY JetScan has identified a note that is incorrectly oriented.
± Users should either:
· Orient the note and return it to the bottom stacker, then press the appropriate denomination value key ($1, $5, $10, etc.).
· Correctly orient the note and return it to the top hopper and press Cont.
14
STOPPING CONDITIONS & RECOVERY
JetScanTM
JetScanTM
STOPPING CONDITIONS & RECOVERY
15
D I S P L AY JetScan has detected a note of a different denomination from those being counted and has stopped. This "stranger" note is the top note in the bottom stacker. This note has not been included in the count.
± Remove the top note in the bottom stacker and press Cont.
These two screens will sequentially flash:
D I S P L AY The wrong denomination value key was pressed.
± Review the top note in the bottom stacker and press the correct
denomination value key.
D I S P L AY The number of notes in the bottom stacker has reached the preset strap limit.
± Remove the notes from the bottom stacker.
JetScan automatically will continue if there are additional notes remaining in the top hopper.
ONLY ON MODELS 4062, 4063, 4064, 4065, 4068: These two screens will sequentially flash:
This line could show different suspect document (SD) codes.
For details, refer to
the SD code chart
below.
D I S P L AY
JetScan sensors have detected a possible counterfeit note. JetScan has stopped with this note as the top note in the bottom stacker. This note has not been included in the count.
± Inspect the top note in the bottom stacker. Next there are two options:
· If it is identified as a counterfeit, place it aside and press Cont. It will not be part of the count.
· If the note is determined to be good, return it to the bottom stacker and press the appropriate denomination value key. JetScan will re-start, and this note will be added to the count.
SD Code
M UV
FL
Possible Causes
· Incorrect-ink error · Worn note
· Incorrect-currency paper · Soiled note
· Incorrect-currency paper · Machine-washed note · Taped note
16
STOPPING CONDITIONS & RECOVERY
JetScanTM
JetScanTM
STOPPING CONDITIONS & RECOVERY
17
ONLY ON MODEL 4069: These two screens will sequentially flash:
This line could show different suspect document (SD) codes.
For details, refer to the SD code chart at right.
D I S P L AY
JetScan sensors have detected a possible counterfeit note. JetScan has stopped with this note as the top note in the bottom stacker. This note has not been included in the count.
± Inspect the top note in the bottom stacker. Next there are two options:
· If it is identified as a counterfeit, place it aside and press Cont. It will not be part of the count.
· If the note is determined to be good, return it to the bottom stacker and press the appropriate denomination value key. JetScan will re-start, and this note will be added to the count.
SD Code S1 S2 S3 S5 S8*
S10* S11*
Possible Causes
· Incorrect-currency paper · Soiled note
· Incorrect-currency paper · Machine-washed note · Taped note
· Incorrect-currency paper · Soiled note
· Incorrect-ink error · Worn note
· Note failed advanced counterfeit test · Worn note
· Incorrect-ink error · Genuine AK Series $100 · Worn note
· Incorrect-ink error · Worn note
* These error codes are most common among super notes, which are high-quality counterfeits.
Notes producing these codes should be carefully examined.
S1 S2 S3 S5
Lower probability of a super note, but commonly identifies poor-quality counterfeit notes
S8 S10 S11
Higher probability of a super note
18
STOPPING CONDITIONS & RECOVERY
JetScanTM
JetScanTM
STOPPING CONDITIONS & RECOVERY
19
These three screens will sequentially flash:
D I S P L AY JetScan is indicating there possibly is a problem with the right, left or both doubles sensors.
± Press Cont to attempt continued operation. If the alarm occurs again,
clean the machine by following the daily cleaning procedures at the front of this booklet. If the message continues to appear, call a local Cummins service representative.
These four screens will sequentially flash:
D I S P L AY JetScan is indicating there possibly is a problem with the ultraviolet (UV) bulb ("BECOMING WEAK," "INTENSITY OUT OF RANGE " or "UNRELIABLE").
± Press Cont to continue operation. If the machine is not equipped with
ultraviolet (UV), be sure to turn the feature off in SETUP (see JetScan operating instructions). If the message continues to appear, contact a local Cummins service representative.
20
STOPPING CONDITIONS & RECOVERY
JetScanTM
My Name