Bestway Air Mattress Owner's Manual with Built-in AC Pump

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

Carefully read, understand, and follow all information in this user manual before installing and using the air mattress. These warnings, instructions, and safety guidelines address some common risks, but they cannot cover all risks and dangers in all cases. Always use caution, common sense, and good judgement when enjoying the air mattress. Retain this information for future use. If instructions are missing, search for them on the website: www.bestwaycorp.com/support.

WARNING

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Motor for short time operation only. Inflate only for 5 minutes and deflate only for 5 minutes. Ensure the motor's run time at a time does not exceed 5 minutes.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Inflate airbed to proper firmness, and most wrinkles should be gone.
• After use, airbeds may require additional air to increase firmness. Add air to proper firmness.

NOTICE: READ THE INSTRUCTIONS COMPLETELY AND SAVE THESE INSTRUCTIONS. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

CAUTION: THERE ARE RISKS WHEN YOU USE THE ARTICLE IN THE OPEN AND/OR AS WATERCRAFT. KEEP AWAY FROM FIRE.

NOTE: Do not exceed the maximum load recommended, or the airbed will be damaged and even explode.

NOTE: The product is not intended for commercial use.

NOTE: Drawings are for illustration purposes only. They may not reflect the actual product. Not to scale.

DISPOSAL

If the product is out of service, please cut it and dispose of it according to your local council. Dispose of the package carefully and thoughtfully. Do not litter. Be a good citizen and dispose of litter in an environmentally friendly manner.

Electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

CLEANING & STORAGE

1. If the product gets dirty, use a clean damp cloth and wipe gently on the flocked and PVC surface. Do not use harsh detergents to clean. Fold and store after the product is dried. Check the product for damage at the beginning of each season and at regular intervals when in use.
2. Before storing the product, release all the air. Store in a cool and dry place.
3. Do not place sharp or heavy objects near or on top of the mattress. Doing so will cause damage and tears.
4. If the product is damaged, please use the provided repair patch.

To repair:

1. Completely deflate the airbed.
2. Clean and dry the damaged area.
3. Apply a repair patch and smooth out any air bubbles.

Product Operation Diagrams

Inflation and Deflation with Built-in AC Pump

Section 1: Inflation

• 1.1: Locate the pump valve. Turn the dial to the 'Inflate' position (indicated by a symbol resembling a fan or air intake).
• 1.2: Connect the power plug to a suitable power outlet. The power indicator light should illuminate.
• 1.3: Turn the dial to the 'Inflate' position. The pump will begin inflating the airbed.
• 1.4: Continue inflating until the airbed reaches the desired firmness and most wrinkles are gone.
• 1.5: Once inflated, turn the dial to the 'Deflate' position (indicated by a symbol resembling air being expelled).
• 1.6: Turn the dial to the 'Deflate' position to stop the pump. Unplug the power cord.

Section 2: Deflation

• 2.1: Locate the pump valve. Turn the dial to the 'Deflate' position.
• 2.2: Connect the power plug to a suitable power outlet. Turn the dial to the 'Deflate' position. The pump will begin deflating the airbed.
• 2.3: Once deflated, turn the dial to the 'Inflate' position to stop the pump. Unplug the power cord.
• 2.4: Ensure the valve is securely closed after deflation.

Section 3: Alternate Inflation/Deflation (if applicable)

• 3.1: Connect the power plug to a suitable power outlet.
• 3.2: Turn the dial to the 'Inflate' position.
• 3.3: Inflate to desired firmness.
• 3.4: Turn the dial to the 'Deflate' position.
• 3.5: Unplug the power cord.

Storage and Repair

Section 4: Folding and Storage

• 4.1: Ensure the airbed is fully deflated. Fold the airbed neatly.
• 4.2: Store the folded airbed in a cool, dry place, away from sharp objects.

Section 5: Cleaning

• 5.1: Gently wipe the flocked and PVC surface with a clean, damp cloth.
• 5.2: Do not use harsh detergents.
• 5.3: Ensure the airbed is completely dry before storing. Recommended storage temperature is around 59°F (15°C).

Section 6: Repairing a Puncture

• 6.1: Locate the damaged area.
• 6.2: Clean and dry the area thoroughly.
• 6.3: Cut a piece of the repair patch to the appropriate size.
• 6.4: Peel the backing off the repair patch.
• 6.5: Apply the patch firmly over the damaged area, smoothing out any air bubbles.
• 6.6: Allow the patch to adhere for at least 30 seconds. For best results, allow 30 minutes before reinflating.

Valve Operation (Model 67486 Example)

Diagram shows a valve with multiple parts. The process involves turning a central component, then potentially unscrewing or adjusting other parts to inflate or deflate.

• 1: Initial valve state.
• 2: Turning the central part.
• 3: Further adjustment or opening of the valve.
• 4: Indicating time or process duration.
• 5: Valve in an open state for inflation/deflation.
• 6: Valve being closed.
• 7: Final closed valve state.

Disposal of Electrical Products

Electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.