LG Innotek Co., Ltd. TWFBR101D PoE Wi-Fi Bridge YZP-TWFBR101D YZPTWFBR101D twfbr101d
TWFBR101D User Manual (PoE Wi-Fi Bridge) by LG Innotek
Inside your life ! PoE Wi-Fi Bridge Manual (PoE: Power over Ethernet) [Model Name : TWFB-R101D ] 2015. 03. 06 . 1. Appearance Description for PoE Wi-Fi Bridge 1. Front Panel - The front panel has the 2-Button and status LEDs in the following figure. Buttons WPS Reset LEDs POWER WLAN DATA CAMERA Button WPS Reset LED Power Description · To connect WPS to AP(Access Point) · Reboot · Reset to Factory Default Description · Solid Yellow Green : Power on · Off : Power is not supplied to the PoE Wi-Fi Bridge WLAN · Solid Yellow Green : Wi-Fi Activity are in process · Blinking Yellow Green : Wireless data is being sent or received. · Blinking Red : The Wireless signal is weak signal · Off : Wi-Fi access fail DATA CAMERA · Blinking Yellow Green : Ethernet link is detected Data Transmission on the port · Off : No data transmission · Blinking Yellow Green : CAMERA link is detected Data Transmission on the port · Off : No data transmission Fig 1. Front View Table 1. Front Description Copyright. 2015. All Rights Reserved. 1 / 12 2. Back/side Panel & Label Information - The back/side panels have the wireless antenna, power plug and 2-Lan ports. - The label on the bottom shows the MAC address, serial Number. AC 110V Power Wireless Antenna Label CAMERA (CAMERA LED) DATA (DATA LED) Fig 2. Back/side View Copyright. 2015. All Rights Reserved. 2 / 12 Fig 3. Label information 2. Installation Guide 1. Log in connection Camera & Wi-Fi Bridge 1) Make sure that your camera is connected to the Wi-Fi Bridge CAMERA port with an Ethernet cable(wired) 2) Turn on the Wi-Fi Bridge and verify the following - The power LED is On. - The CAMERA LED is on for the LAN port that is connected to your Power device camera. - The WLAN LED is blinking. 3) Launch internet browser and enter http://172.19.1.254 in the address field. You are prompted to login; WLAN LAN Cable(CAMERA) CAMERA Fig 4. Login connection Copyright. 2015. All Rights Reserved. 3 / 12 2. Log in to the PoE 1) After entering http://172.19.1.254 , you can show Realtek WLAN AP webserver. Copyright. 2015. All Rights Reserved. Fig 5. Realtek WLAN webserver 4 / 12 3. Wireless Site Survey 1) Please click "Wireless" in the webserver. 2) Please click "Site Survey" in the webserver( , ), to fine AP list Click Click Copyright. 2015. All Rights Reserved. Fig 6. Wireless Site Survey 5 / 12 4. AP Connection 1) After "Site Survey", you can show AP lists. 2) Please select wanted SSID(AP Name) and click "Next" Copyright. 2015. All Rights Reserved. Fig 7. SSID Selection 6 / 12 Click 3) Please click "Connect" 4) After "Connect" click, You can show "Please Wait" message 5) It will be connected. Please click "Reboot Later" 6) Finally, Please close your web browser. Click Copyright. 2015. All Rights Reserved. Fig 8. SSID Connection 7 / 12 Click 3. Regulation Information INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user's authority to operate the equipment. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Copyright. 2015. All Rights Reserved. 8 / 12 4. Regulation Information (French) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Copyright. 2015. All Rights Reserved. 9 / 12 5. Appendix 1. WPS Function - You can use WPS to connect AP without any password(WPA or WPA2). Push AP' WPS button. Push PoE' WPS Button(During 3 secs). WPS Reset When try to connect AP, WLAN LED is pulsing RED. After connect AP, WLAN LED is blinking Yellow Green. If you didn't push PoE' WPS Button within 2min, It will be disconnected. * Notice - If you want to use WPS function, your AP must have WPS function. 2. Reset Function - If you push RESET Button for 3secs, the PoE will restart. 3. Factory Default Setting - Reset button can also be used to clear all data and restore the factory default settings. Press the Reset button(during 10 secs). Release the Reset button. PoE will return to the factory configuration settings shown in the following table. Feature User name (case-sensitive) printed on product label Password (case-sensitive) printed on product label Static IP address Fig 9. WPS / Reset Default settings admin xxxxx 172.19.1.254 Ethernet MAC address See bottom label. Subnet mask 255.255.255.0 DHCP client Disabled Table 2. PoE default configuration settings Copyright. 2015. All Rights Reserved. 10 / 12 4. PIN mode WPS Function of webserver Please click "Wireless" in the webserver. Please click "WPS" in the webserver. If you use PIN mode WPS, first input Self-PIN Number to AP. After that click Start PIN. Click ok. Click Click Click Copyright. 2015. All Rights Reserved. Click 11 / 12 5. PIN mode WPS Function of webserver Please click "Wireless" in the webserver. Please click "WPS" in the webserver. If you use PBC mode WPS in webserver, first push the WPS button of AP. After that click Start PBC. Click ok. Click Click Click Click Copyright. 2015. All Rights Reserved. 12 / 12Microsoft PowerPoint 2010