AquaSource Two Handle Lavatory Faucet

Product Overview

This document provides installation, care, troubleshooting, and warranty information for the AquaSource Two Handle Lavatory Faucet.

For assistance with questions, problems, or missing parts, please contact our customer service department at 1-866-417-7564. Hours are 8 a.m. - 8 p.m., EST, Monday - Friday.

The faucet is depicted as a two-handle lavatory faucet in a line drawing.

Package Contents

Verify all parts are present before assembly. The package includes:

⚠️ WARNINGS AND CAUTIONS

• Follow these installation instructions carefully. Proper installation is the installer's responsibility.
• Failure to follow correct installation procedures can cause the faucet to become loose, which can result in serious injury.
• The products should be installed by a locally licensed plumber.
• This product is engineered to meet EPA Watersense flow requirements. The flow rate is governed by the aerator. If replacement is required, request a Watersense compliant lavatory faucet aerator to retain water-conserving qualities. The max flow rate is 1.5 GPM (5.7 LPM) at 60 PSI.
• Do not put plumber's putty on threads.

PREPARATION

Before beginning assembly, installation, or operation, ensure all parts are present. Compare parts with the package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install, or operate the product. Contact customer service for replacement parts.

Estimated Assembly Time: 12 minutes

Tools Required for Assembly (not included): None.

Helpful Tools: Adjustable Wrench

ASSEMBLY INSTRUCTIONS

1. Turn off water supply.

   Diagram: Shows water supply valves being turned off.

2. Install faucet (A) through top of sink.

   Diagram: Shows faucet (A) being placed into sink holes.

3. Tighten lock nuts (C).

   Diagram: Shows lock nuts (C) being tightened onto faucet shanks from underneath the sink.

4. Attach water supply lines with coupling nuts (sold separately).

   Diagram: Shows flexible water supply lines being connected to the faucet shanks using coupling nuts.

5. Install drain assembly.

   ℹ️ NOTE: Opening for ball rod must face towards rear of sink.

   Diagram: Shows drain assembly parts (AA, BB, CC, DD) being installed in the sink, with a callout indicating the correct orientation for the ball rod opening.

6. Insert plunger (EE).

   ℹ️ NOTE: Plunger can only be inserted in one direction.

   Diagram: Shows plunger (EE) being inserted into the drain body.

7. Insert ball rod (HH) into drain assembly (DD). Tighten sleeve.

   Diagram: Shows ball rod (HH) being inserted into the drain body (DD) and a sleeve being tightened to secure it.

8. Insert lift rod (FF) through faucet and attach perforated strap (GG) to lift rod. Push button to allow lift rod to slide through. Release to lock.

   Diagram: Shows lift rod (FF) passing through the faucet body and being connected to the perforated strap (GG). A button is shown being pressed to allow movement.

9. Adjust ball rod (HH) to the down position. Attach to strap (GG).

   Diagram: Shows ball rod (HH) in the down position and connected to the strap (GG).

10. Turn on water supply.

    Diagram: Shows water supply valves being turned on.

11. Remove aerator (B).

    Diagram: Shows aerator (B) being unscrewed from the faucet spout.

12. Flush out any debris and check for leaks around drain.

    Diagram: Shows water running through the faucet and out the spout to flush the system.

13. Replace aerator (B).

    Diagram: Shows aerator (B) being screwed back onto the faucet spout.

CARE AND MAINTENANCE

• To protect and maintain the finish of your faucet, clean only with a soft, damp cloth.
• Do not use a detergent or cleanser that may harm the finish.
• Do not use plumber's putty on plastic components.

TROUBLESHOOTING

For assistance with questions, problems, or missing parts, please contact our customer service department at 1-866-417-7564. Hours are 8 a.m. - 8 p.m., EST, Monday - Friday.

WARRANTY

The manufacturer warrants this faucet to be free from defects in workmanship and material present at time of shipment from the factory for a limited lifetime from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defects at no charge or, at their option, replace the faucet with a comparable or superior model. To obtain warranty service, call the customer service department at 1-866-417-7564 for return authorization and shipping instructions. A copy of the sales receipt may be required as proof of purchase. All costs of removal and reinstallation are the responsibility of the purchaser. Any damage to the faucet by accident, misuse, or improper installation, or by affixing accessories not produced by the manufacturer, are the purchaser's responsibility. The manufacturer assumes no responsibility whatsoever for faucet installation during the warranty period. There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for incidental, consequential, or special damages arising in connection with product use or performance except as otherwise accorded by law. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties.

REPLACEMENT PARTS LIST

For replacement parts, call the customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.

Diagram: An exploded view of the faucet and drain assembly is provided, with numbered components corresponding to the list below.

* Watersense Compliant Lavatory Faucet Aerator

Printed in China