PDF preview unavailable.
Open the PDF or use the Download button.
kd-r895bts-instruction-manual
KD-R995BTS / KD-R990BTS / KD-R895BTS / KD-R792BT / KD-R790BT / KD-RD99BTS / KD-RD79BT / KD-R99MBS
CD RECEIVER
INSTRUCTION MANUAL
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
CAUTION This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body.
FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. · Consult the dealer or an experienced radio/TV technician for help.
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")
Article 2 License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 3 Conditions for Grant of License
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.
Article 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Article 5 Indemnification of Licensor
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.
Article 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.
Article 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.
Article 8 Termination
In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.
Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10 Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.
Article 11 Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).
Important Notice concerning the Software
-jansson
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Article 12 Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force. 2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or
settled upon good-faith consultation between the Licensor and the User. 3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and
relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
CONTENTS
BEFORE USE
2
BASICS
3
GETTING STARTED
4
1 Cancel the demonstration
2 Set the clock and date
3 Set the basic settings
RADIO
5
CD/USB/iPod/ANDROID
8
Pandora®
10
iHeartRadio®
11
Spotify
12
SiriusXM® Radio
13
BLUETOOTH®
16
AUX
24
AUDIO SETTINGS
24
DISPLAY SETTINGS
29
LEARNING STEERING
REMOTE CONTROL
31
REFERENCES
32
Maintenance
More information
TROUBLESHOOTING
36
SPECIFICATIONS
39
INSTALLATION/
CONNECTION
40
2
BEFORE USE
IMPORTANT · To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual. · Please keep the manual in a safe and accessible place for future reference.
WARNING · Do not operate any function that takes your attention away from safe driving. · Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution Volume setting: · Adjust the volume so that you can hear sounds outside the car to prevent accidents. · Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General: · Avoid using the external device if it might hinder safe driving. · Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data. · Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit. · If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate. · Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire
connected ( 42). Turn off the unit when parking at a low ceiling area.
Remote control (RM-RK52): · Do not leave the remote control in hot places such as on the dashboard. · The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type. · The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
How to read this manual · Operations are explained mainly using buttons on the faceplate of KD-R995BTS. · English indications are used for the purpose of explanation. You can select the display language from the menu. ( 5) · [XX] indicates the selected items. · ( XX) indicates references are available on the stated page.
BASICS
Faceplate
Volume knob
Loading slot
Display window
Remote control (RM-RK52) (supplied for KD-R792BT) Other models can be remotely controlled with an optionally purchased remote control.
Remote sensor (Do not expose to bright sunlight.)
Detach button
Attach
Detach
KD-R995BTS: USB cable from the rear of the unit
How to reset
Reset the unit within 5 seconds after detaching the faceplate.
To Turn on the power
Adjust the volume
On the faceplate
Press
.
· Press and hold to turn off the power.
Turn the volume knob.
Select a source
Change the display information
Press the volume knob to mute the sound or pause playback. · Press again to cancel. The volume level returns to the previous
level before muting or pause.
· Press · Press
Press
repeatedly. , then turn the volume knob within 2 seconds.
repeatedly. ( 34, 35)
Pull out the insulation sheet when using for the first time.
How to replace the battery
On the remote control
( Not available )
Press
or
· Press and hold
volume to 15.
. to continuously increase the
Press to mute the sound or pause playback. · Press again to cancel. The volume level returns to the
previous level before muting or pause.
Press SOURCE repeatedly.
( Not available ) 3
GETTING STARTED
1 Cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to [YES], 5), the display shows: "CANCEL DEMO" "PRESS" "VOLUME KNOB"
1 Press the volume knob. [YES] is selected for the initial setup.
2 Press the volume knob again. "DEMO OFF" appears.
2 Set the clock and date
1 Press and hold . 2 Turn the volume knob to select [CLOCK], then press the knob.
To adjust the clock 3 Turn the volume knob to select [CLOCK ADJUST], then press the knob. 4 Turn the volume knob to make the settings, then press the knob.
Hour Minute 5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob.
To set the date 7 Turn the volume knob to select [DATE SET], then press the knob. 8 Turn the volume knob to make the settings, then press the knob.
Day Month Year
9 Press
to exit.
To return to the previous setting item, press
.
3 Set the basic settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press
to exit.
To return to the previous setting item, press
.
Default: XX
SYSTEM
KEY BEEP
(Not applicable when 3-way crossover is selected.) ON: Activates the keypress tone. ; OFF: Deactivates.
SOURCE SELECT AM SRC* PANDORA SRC*
IHEART SRC*
SPOTIFY SRC*
BUILT-IN AUX*
ON: Enables AM in source selection. ; OFF: Disables. ( 5)
ON: Enables PANDORA FRONT/PANDORA REAR/PANDORA in source selection. ; OFF: Disables. ( 10)
ON: Enables IHEARTRADIO-F/IHEARTRADIO-R/IHEARTRADIO in source selection. ; OFF: Disables. ( 11)
ON: Enables SPOTIFY FRONT/SPOTIFY REAR/SPOTIFY in source selection. ; OFF: Disables. ( 12)
ON: Enables AUX in source selection. ; OFF: Disables. ( 24)
USER S. REMO
(for KD-R792BT) See page 31 for details.
* Not displayed when the corresponding source is selected.
4
GETTING STARTED
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).
RADIO
FACTORY RESET CLOCK TIME SYNC
CLOCK DISPLAY
ENGLISH ESPANOL
YES: Resets the settings to default (except the stored station). ; NO: Cancels.
ON: The clock time is automatically set using the Clock Time (CT) data in FM Radio Broadcast Data System signal/FM Radio Data System signal. ; OFF: Cancels.
ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels.
Select the display language for menu and music information if applicable. By default, ENGLISH is selected.
"ST" or "STEREO" lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1 Press
repeatedly to select FM or AM.
2 Press
(or press on the remote control) to search for a station automatically.
(or)
Press and hold
(or press and hold on the remote control) until "M" flashes,
then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station While listening to a station.... Press and hold one of the number buttons (1 to 6).
(or) 1 Press and hold the volume knob until "PRESET MODE" flashes. 2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and "MEMORY" appears.
Select a stored station
Press one of the number buttons (1 to 6).
(or)
1 Press
.
2 Turn the volume knob to select a preset number, then press the knob.
5
RADIO
Other settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press
to exit.
To return to the previous setting item, press
.
Default: XX
TUNER SETTING (except KD-R792BT)
RADIO TIMER
Turns on the radio at a specific time regardless of the current source. 1 ONCE/DAILY/WEEKLY/OFF: Select how often the timer will be
turned on. 2 FM/AM/SIRIUS XM*1: Select the source. 3 01 to 18 (for FM/SIRIUS XM)/01 to 06 (for AM): Select the preset
station. 4 Set the activation day*2 and time. "M" lights up when complete.
Radio Timer will not activate for the following cases. · The unit is turned off. · [OFF] is selected for [AM SRC] in [SOURCE SELECT] after Radio Timer
for AM is selected. ( 4)
SSM
SSM 0106 /SSM 0712 /SSM 1318: Automatically presets up to 18
stations for FM. "SSM" stops flashing when the first 6 stations are stored.
Select SSM 0712/SSM 1318 to store the following 12 stations.
IF BAND
AUTO: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
MONO SET
ON: Improves the FM reception, but the stereo effect will be lost. ; OFF: Cancels.
AREA
N.AMERICA: For North/Central/South America, AM/FM intervals:
10 kHz/200 kHz. ; S.AMERICA: For some South American countries, AM/
FM intervals: 10 kHz/50 kHz. ; EUROPE: For any other areas, AM/FM
intervals: 9 kHz/50 kHz.
PTY SEARCH*3
Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
*1 KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS: Selectable only when SiriusXM Vehicle Tuner is connected. ( 13)
*2 Selectable only when [ONCE] or [WEEKLY] is selected in step 1. *3 Only for FM source.
PTY code (except KD-R792BT) NEWS, INFORM (information), SPORTS, TALK, ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40, COUNTRY, OLDIES, SOFT, NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B (rhythm and blues), SOFT R&B (soft rhythm and blues), LANGUAGE, REL MUSC (religious music), REL TALK (religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP (Spanish talk), MUSC ESP (Spanish music), HIP HOP, WEATHER
6
RADIO
Default: XX
TUNER SETTING (for KD-R792BT)
RADIO TIMER
Turns on the radio at a specific time regardless of the current source. 1 ONCE/DAILY/WEEKLY/OFF: Select how often the timer will be turned
on. 2 FM/AM: Select the band. 3 01 to 18 (for FM)/01 to 06 (for AM): Select the preset station. 4 Set the activation day*1 and time. "M" lights up when complete.
Radio Timer will not activate for the following cases. · The unit is turned off. · [OFF] is selected for [AM SRC] in [SOURCE SELECT] after Radio Timer for
AM is selected. ( 4)
SSM
SSM 0106/SSM 0712/SSM 1318: Automatically presets up to 18
stations for FM. "SSM" stops flashing when the first 6 stations are stored.
Select SSM 0712/SSM 1318 to store the following 12 stations.
IF BAND
AUTO: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
MONO SET
ON: Improves the FM reception, but the stereo effect will be lost. ; OFF: Cancels.
NEWS SET*2 ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels.
REGIONAL*2 ON: Switches to another station only in the specific region using the "AF" control. ; OFF: Cancels.
AF SET*2
ON: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor. ; OFF: Cancels.
TI
ON: Allows the unit to temporarily switch to Traffic Information if available
("TI" lights up) while listening to all sources except in AM. ; OFF: Cancels.
AREA
N.AMERICA: For North/Central/South America, AM/FM intervals:
10 kHz/200 kHz. ; S.AMERICA: For some South American countries, AM/FM
intervals: 10 kHz/50 kHz. ; EUROPE: For any other areas, AM/FM intervals:
9 kHz/50 kHz.
PTY SEARCH*2 Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
*1 Selectable only when [ONCE] or [WEEKLY] is selected in step 1. *2 Only for FM source.
PTY code (for KD-R792BT) NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT
7
CD/USB/iPod/ANDROID
Start playback
The source changes automatically and playback starts.
CD Eject disc
Label side
USB input terminal USB
USB 2.0 cable*1 (commercially available)
KD-R995BTS: You can also connect to the USB cable from the rear of the unit.
iPod/iPhone
Accessory of the iPod/ iPhone*1
ANDROID*2
USB cable*1 (commercially available)
8
Selectable source: · KD-R995BTS: CD/USB FRONT/USB REAR/iPod FRONT/iPod REAR/ANDROID FRONT/ANDROID REAR · KD-R990BTS/KD-R895BTS/KD-R792BT/KD-R790BT/KD-RD99BTS/KD-RD79BT/KD-R99MBS: CD/USB/
iPod USB/ANDROID
To Reverse/Fast-forward*3 Select a track/file Select a folder*4 Repeat play*5
Random play*5
On the faceplate
On the remote control
Press and hold
.
Press and hold .
Press
.
Press .
Press
.
Press .
Press repeatedly.
TRACK REPEAT/ALL REPEAT
: Audio CD
TRACK REPEAT/FOLDER REPEAT/ALL REPEAT : MP3/WMA/AAC/WAV/
FLAC file
ONE REPEAT/ALL REPEAT/REPEAT OFF : iPod or ANDROID
Press repeatedly.
ALL RANDOM/RANDOM OFF
: Audio CD
FOLDER RANDOM/ALL RANDOM/RANDOM OFF : MP3/WMA/AAC/WAV/
FLAC file
SONG RANDOM/ALL RANDOM/RANDOM OFF : iPod or ANDROID
*1 Do not leave the cable inside the car when not using. *2 When connecting an Android device, "Press [VIEW] to install JVC MUSIC PLAY APP" is shown. Follow the instructions to install the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device
before connecting. *3 For ANDROID: Applicable only when [AUTO MODE] is selected. ( 9) *4 For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID. *5 For iPod/ANDROID: Applicable only when [HEAD MODE]/[AUTO MODE] is selected. ( 9)
CD/USB/iPod/ANDROID
Select control mode
While in iPod FRONT/iPod REAR/iPod USB source, press repeatedly. HEAD MODE: Control iPod from this unit. IPHONE MODE: Control iPod using the iPod itself. However, you can still
play/pause or file skip from this unit.
While in ANDROID FRONT/ANDROID REAR/ANDROID source, press repeatedly.
AUTO MODE: Control Android device from this unit via JVC MUSIC PLAY application installed in the Android device.
AUDIO MODE: Control Android device using the Android device itself via other media player applications installed in the Android device. However, you can still play/pause or file skip from this unit.
Select music drive
While in USB FRONT/USB REAR/USB source, press
repeatedly.
Stored songs in the following drive will be played back. · Selected internal or external memory of a smartphone (Mass Storage
Class). · Selected drive of a multiple drives device.
Settings to use JVC Remote application
JVC Remote application is designed to control the JVC car receiver's operations from the iPhone/iPod (via USB input terminal).
Preparation: Install the latest version of JVC Remote application on your device before connecting.
You can make the settings in the same way as connection via Bluetooth. ( 22)
Select a file from a folder/list
For iPod/ANDROID, applicable only when [HEAD MODE]/[AUTO MODE] is selected.
1 Press
.
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick search (applicable only for CD, USB FRONT, USB REAR, USB, ANDROID FRONT, ANDROID REAR and ANDROID source) If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
Alphabet search (applicable only for iPod FRONT, iPod REAR, iPod USB, ANDROID FRONT, ANDROID REAR and ANDROID source) You can search for a file according to the first character.
For iPod FRONT/iPod REAR/iPod USB source
Press
or turn the volume knob quickly to select the
desired character (A to Z, 0 to 9, OTHERS).
· Select "OTHERS" if the first character is other than A to Z, 0 to 9.
For ANDROID FRONT/ANDROID REAR/ANDROID source
1 Press
to enter character search.
2 Turn the volume knob to select the desired character.
^A^:
Upper case letters (A to Z)
_A_:
Lower case letters (a to z)
-0-:
Numbers (0 to 9)
-OTHERS-: Character other than A to Z, 0 to 9
3 Press the volume knob to start searching.
· To return to the previous setting item, press
.
· To cancel, press and hold
.
9
Pandora® (except KD-R792BT)
Preparation: Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora. · Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. ( 4)
Start listening
1 Open the Pandora application on your device. 2 Connect your device to the USB input terminal.
USB input terminal Accessory of the iPod/iPhone*1
and/or
KD-R995BTS: You can also connect to the USB cable from the rear of the unit.
3 Press
repeatedly to select PANDORA FRONT/PANDORA
REAR/PANDORA.
Broadcast starts automatically.
To
Playback/pause
Skip a track Thumbs up or thumbs down*2
On the faceplate
Press the volume knob.
Press T.
Press
.
*1 Do not leave the cable inside the car when not using. *2 If thumbs down is selected, the current track is skipped.
On the remote control Press . Press I. Press .
Create and store a new station
1 Press
.
2 Turn the volume knob to select [NEW STATION], then press the knob.
3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (3, 4, 5 or 6) to store.
To select a stored station: Press one of the number buttons (3, 4, 5 or 6).
Search for a registered station
1 Press
.
2 Turn the volume knob to select an item, then press the knob.
[BY DATE]: According to the registered date
[A-Z]: By alphabetical order
3 Turn the volume knob to select the desired station, then press the
knob.
To cancel, press and hold
.
Bookmark current song information
Press and hold the volume knob. "BOOKMARKED" appears and the information is stored to your device. · The bookmark is available on your Pandora account but not on this
unit.
10
iHeartRadio® (except KD-R792BT)
Preparation: Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio. · Select [ON] for [IHEART SRC] in [SOURCE SELECT]. ( 4)
Start listening 1 Open the iHeartAuto application on your device. 2 Connect your device to the USB input terminal.
USB input terminal Accessory of the iPod/iPhone*
and/or
KD-R995BTS: You can also connect to the USB cable from the rear of the unit.
3 Press
repeatedly to select IHEARTRADIO-F/IHEARTRADIO-R/
IHEARTRADIO.
Broadcast starts automatically
* Do not leave the cable inside the car when not using.
To
Playback/pause
Skip a track for custom station
Thumbs up or thumbs down
Create a new/ custom station
Scan for live station
On the faceplate Press the volume knob. Press T.
On the remote control Press . Press I.
Press
.
Press .
Press and hold the volume knob.
( Not available )
1 Press 3 to start
2
scanning. Press 3 again to listen
( Not available )
to the station.
Search and store a station
1 Press
.
2 Turn the volume knob to select a category, then press the knob.
3 Turn the volume knob to select the desired station, then press the
knob.
When a city list appears, you can search cities in alphabetical order by
turning the volume knob quickly.
To cancel, press and hold
.
To store a station: Press and hold one of the number buttons (4, 5 or 6). To select a stored station: Press one of the number buttons (4, 5 or 6).
11
Spotify
Preparation: Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify. · Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. ( 4)
Start listening
1 Open the Spotify application on your device. 2 Connect your device to the USB input terminal.
USB input terminal Accessory of the iPod/iPhone*
To Repeat play*3
Random play*3
On the faceplate
Press repeatedly.
ALL REPEAT, ONE REPEAT*1, REPEAT OFF
Press
repeatedly *1.
ALL RANDOM, RANDOM OFF
On the remote control ( Not available ) ( Not available )
*1 Available for premium account users only. *2 This feature is available for tracks in Radio only. If thumbs down is selected, the current
track is skipped. *3 Available for tracks in Playlists only.
and/or
KD-R995BTS: You can also connect to the USB cable from the rear of the unit.
3 Press
repeatedly to select SPOTIFY FRONT/SPOTIFY REAR/
SPOTIFY.
Broadcast starts automatically
* Do not leave the cable inside the car when not using.
To
Playback/pause
Skip a track Thumbs up or thumbs down*2 Start radio
On the faceplate
Press the volume knob.
Press S*1 / T.
Press
.
Press and hold 5.
On the remote control Press . Press H*1 / I. Press .
( Not available )
12
Save favorite song information
While listening to the Radio on Spotify...
Press and hold the volume knob. "SAVED" appears and the information is stored to "Your Music" or "Your Library" on your Spotify account.
To unsave, repeat the same procedure. "REMOVED" appears and the information is removed from "Your Music" or "Your Library" on your Spotify account.
Search for a song or station
1 Press
.
2 Turn the volume knob to select a list type, then press the knob.
The list types displayed differ depending on the information sent
from Spotify.
3 Turn the volume knob to select the desired song or station, then
press the knob.
You can browse through the list quickly by turning the volume knob
quickly.
To cancel, press and hold
.
SiriusXM® Radio (for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required.
Preparation: 1 Connect the optional SiriusXM Vehicle Tuner
(commercially available).
Antenna
Expansion port on the rear panel
SiriusXM Vehicle Tuner
2 Check your Radio ID for activation. The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Vehicle Tuner and its packaging. The Radio ID does not include the letters I, O, S or F.
Start listening
1 Press
repeatedly to select SIRIUS XM.
2 Press
.
" " lights up.
3 Turn the volume knob to select a CATEGORY, then press the knob.
4 Turn the volume knob to select a category from the list, then press the knob.
If "ALL CHANNEL" is selected, all the available channels will be shown.
5 Turn the volume knob to select a channel, then press the knob.
(or)
Press
to search for a channel manually.
· Pressing and holding
changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel. ( 15)
Settings in memory
You can store up to 18 channels.
Store a channel
While listening to a channel.... Press and hold one of the number buttons (1 to 6).
(or) 1 Press and hold the volume knob until "PRESET MODE" flashes. 2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and "MEMORY" appears.
Select a stored channel
Press one of the number buttons (1 to 6).
(or)
1 Press
.
2 Turn the volume knob to select PRESET, then press the knob.
3 Turn the volume knob to select a preset number, then press the knob.
(or)
Press
on the remote control.
13
SiriusXM® Radio (for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)
SiriusXM ReplayTM
While listening to a channel.... 1 Press the volume knob.
" " lights up and the unit memorizes this paused position. 2 Press the volume knob to start Replay.
Replay starts from the paused position in step 1.
During Replay... To
Playback/pause
Skip backward/ forward Rewind/Fast-forward Go to Live and exit Replay
On the faceplate
Press the volume knob.
Press
.
On the remote control Press . Press .
Press and hold
. Press and hold .
Press and hold the volume knob.
Press and hold .
1 Press
.
2 Turn the volume knob
to select LIVE, then
press the knob.
SmartFavorites and TuneStartTM
User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.
Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.
Using SiriusXM tuner models later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.
* · " " appears at the last character of the channel name for the SmartFavorites channels.
When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content. · Playback starts from the beginning of the song if [TUNE START] is set
to [ON] ( 15) for most music channels stored as a SmartFavorite.
To
On the faceplate
Select a stored SmartFavorite channel
Press one of the number buttons (1 to 6).
1 Press
.
2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset
number, then press the knob.
Cancel SmartFavorites channels
Reassign SmartFavorites channels
1 Press
.
2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset
number, then press and hold the knob.
*" " is removed from the last character.
Repeat steps 1 to 3 of cancelling SmartFavorites
channels.
*" " appears at the last character.
14
SiriusXM® Radio (for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)
TuneScanTM
You can get a short preview of the songs that you have missed on each of your SmartFavorites music channels or currently tuned music channel.
1 Press
.
2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
· To listen to the current song, press the volume knob to stop scanning.
The unit continues playing the current song.
· To select the previous/next song, press
.
· To cancel scanning, press and hold the volume knob. Playback returns
to the channel before you entered TuneScan.
SiriusXM settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press
to exit.
To return to the previous setting item, press
.
SIRIUS XM CHANNEL LOCK
Default: XX
To unlock settings:
1 Turn the volume knob to select a number.
2 Press
to move to the entry position.
3 Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4 Press the volume knob to confirm.
CODE SET
1 Press the volume knob to enter [NEW CODE].
2 Turn the volume knob to select a number.
3 Press
to move to the entry position.
4 Repeat steps 2 and 3 to enter a new 4-digit pass code.
5 Press the volume knob to confirm.
6 Repeat steps 2 to 5 to reconfirm the pass code.
· Make a note of the new pass code to enter channel lock settings
for next time.
LOCK SETTING
MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects the individual channels the user wants to lock. ; OFF: Cancels.
CHANNEL EDIT*1
1 Turn the volume knob to select a category, then press the knob.
2 Turn the volume knob to select a channel you want to lock, then
press the knob.
"L" appears in front of the channel number.
3 Press and hold
to exit.
CHANNEL CLEAR*1 YES: Clears all the locked channels. ; NO: Cancels.
TUNE START*2
ON: All qualified music channels in the SmartFavorites will start playback from the beginning of the song. ; OFF: Cancels.
SIGNAL LEVEL
Shows the strength (NO SIGNAL/WEAK/GOOD/STRONG) of the current received signal.
BUFFER USAGE
Shows the memory usage (0% to 100%) for Replay buffer.
SXM RESET
YES: Resets stored channel and lock setting to default. ; NO: Cancels.
*1 Displayed only when [USER DEFINED] is selected. *2 Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports
SmartFavorites.
15
BLUETOOTH®
BLUETOOTH -- Connection
Supported Bluetooth profiles Hands-Free Profile (HFP) Advanced Audio Distribution Profile (A2DP) Audio/Video Remote Control Profile (AVRCP) Serial Port Profile (SPP) Phonebook Access Profile (PBAP) Supported Bluetooth codecs Sub Band Codec (SBC) Advanced Audio Coding (AAC)
Connect the microphone
MIC (microphone input terminal)*
Microphone (supplied)
Rear panel
Adjust the microphone angle
Secure using cord clamps (not supplied) if necessary.
* For the location of the microphone input terminal/microphone input jack, refer to page "Connecting external amplifiers" on page 43.
Pair and connect a Bluetooth device for the first time
1 Press
to turn on the unit.
2 Search and select "KD-R9 BTS"/"KD-R8 BTS"/"KD-R7 BT"/"KD-RD9 BTS"/
"KD-RD7 BT"/"KD-R9 MBS" on the Bluetooth device.
"BT PAIRING" flashes on the display.
· For some Bluetooth devices, you may need to enter the Personal Identification Number
(PIN) code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) "[Device Name]" "XXXXXX" "VOL YES" "BACK NO"
"XXXXXX" is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device are the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) "[Device Name]" "VOL YES" "BACK NO"
Press the volume knob to start pairing.
· If "PAIRING" "PIN 0000" scrolls on the display, enter the PIN code "0000" into the
Bluetooth device.
You can change to a desired PIN code before pairing. ( 20)
· If only "PAIRING" appears, operate the Bluetooth device to confirm pairing.
"PAIRING COMPLETED" appears when pairing is completed and " " will light up when the Bluetooth connection is established.
· This unit supports Secure Simple Pairing (SSP). · Up to five devices can be registered (paired) in total. · Once the pairing is completed, the Bluetooth device will remain registered in the unit even if
you reset the unit. To delete the paired device, 20, [DEVICE DELETE]. · A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at
any time. However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices. ( 21) · Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. · Refer to the instruction manual of the Bluetooth device for more information.
16
BLUETOOTH®
Auto Pairing
When you connect iPhone/iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.
BLUETOOTH -- Mobile phone
Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if: Bluetooth function of the connected device is
turned on. [AUTO PAIRING] is set to [ON]. ( 20) JVC MUSIC PLAY application is installed on
the Android device ( 8) and [AUTO MODE] is selected ( 9).
Receive a call
When there is an incoming call: · KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS:
The buttons will blink in the color you have selected in [RING COLOR]. ( 18) KD-R792BT/KD-R790BT/KD-RD79BT: The buttons will blink in the blinking pattern you have selected in [RING ILLUMI]. ( 18) · The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 18)
During a call: · KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS:
The buttons stop blinking and illuminate in the color you have selected in [RING COLOR]. ( 18) KD-R792BT/KD-R790BT/KD-RD79BT: The buttons stop blinking. · If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
The following operations may differ or not available depending on the connected phone.
To First incoming call...
Answer a call Reject a call
End a call
On the faceplate
On the remote control
Press
or the volume knob. Press
.
Press and hold
or the
Press and hold
.
volume knob.
Press and hold
or the
Press and hold
.
volume knob.
17
BLUETOOTH®
To
On the faceplate
While talking on the first incoming call...
Answer another incoming Press
or the
call and hold the current volume knob.
call
Reject another incoming Press and hold
call
or the volume knob.
While having two active calls...
End current call and activate held call
Press and hold or the volume knob.
Swap between the
Press .
current call and held call
Adjust the phone volume*1 Turn the volume knob
[00] to [35] (Default: [15])
during a call.
Switch between hands-free Press
and private talk modes*3
a call.
during
On the remote control
( Not available ) ( Not available )
Press and hold .
( Not available )
Press
*2 or
during a call.
( Not available )
*1 This adjustment will not affect the volume of the other sources.
*2 Press and hold
to continuously increase the volume to 15.
*3 Operations may vary according to the connected Bluetooth device.
Improve the voice quality
While talking on the phone....
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press
to exit.
To return to the previous setting item, press
.
Default: XX
MIC GAIN NR LEVEL ECHO CANCEL
LEVEL 10 to LEVEL +10 (LEVEL 04): The sensitivity of the microphone increases as the number increased.
LEVEL 05 to LEVEL +05 (LEVEL 00): Adjust the noise reduction level until the least noise is being heard during a phone conversation.
LEVEL 05 to LEVEL +05 (LEVEL 00): Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.
Make the settings for receiving a call
1 Press
to enter Bluetooth mode.
2 Turn the volume knob to select an item (see the following
table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
To return to the previous setting item, press
.
SETTINGS AUTO ANSWER RING COLOR
RING ILLUMI
Default: XX
01 SEC to 30 SEC: The unit answers incoming call automatically in the selected time (in seconds). ; OFF: Cancels.
KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/ KD-R99MBS: COLOR 01 to COLOR 49 (COLOR 08): Selects the light color for the buttons as notification when there is an incoming call and during a call. ; OFF: Cancels.
KD-R792BT/KD-R790BT/KD-RD79BT: BLINK 01 to BLINK 05 (BLINK 02): Selects the blinking pattern for the buttons as notification when there is an incoming call. ; OFF: Cancels.
18
BLUETOOTH®
BATT/SIGNAL* KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS: AUTO: Shows the strength of the battery and signal when the unit detects a Bluetooth device and the Bluetooth device is connected. ; OFF: Cancels.
* Functionality depends on the type of the phone used.
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.
1 Press
to enter Bluetooth mode.
"(First device name)" appears.
· If two Bluetooth phones are connected, press
again to switch to
another phone.
"(Second device name)" appears.
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
To return to the previous setting item, press
.
RECENT CALL PHONEBOOK
(Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number.
· "<" indicates call received, ">" indicates call made, "M" indicates call missed.
· "NO HISTORY" appears if there is no recorded call history or call number. 2 Press the volume knob to call.
(Applicable only if the phone supports PBAP.)
1 Press
to select the desired letter (A to Z, 0 to 9, and OTHERS).
· "OTHERS" appears if the first character is other than A to Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
· The phonebook of the connected phone is automatically transferred to the unit when pairing.
· This unit can display only non-accent letters. (Accent letters such as "Ú" is showns as "U".)
DIAL NUMBER
1 Turn the volume knob to select a number (0 to 9) or character
( , #, +).
2 Press
to move the entry position.
Repeat steps 1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
VOICE
Speak the name of the contact you want to call or the voice command to control the phone functions. ( Make a call using voice recognition)
Make a call using voice recognition
1 Press and hold
to activate the connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
· Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
· This unit also supports the intelligent personal assistant function of iPhone.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press
to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK] or
[DIAL NUMBER], then press the knob.
3 Turn the volume knob to select a contact or enter a phone
number.
If a contact is selected, press the volume knob to show the phone
number.
4 Press and hold one of the number buttons (1 to 6).
"MEMORY P(selected preset number)" appears when the contact
is stored.
To erase a contact from the preset memory, select [DIAL NUMBER] in step 2 and store a blank number.
19
BLUETOOTH®
Make a call from memory
1 Press
to enter Bluetooth mode.
2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
"NO PRESET" appears if there is no contact stored.
Bluetooth mode settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then press the
knob.
3 Repeat step 2 until the desired item is selected/activated or follow the instructions
stated on the selected item.
4 Press
to exit.
To return to the previous setting item, press
.
BT MODE PHONE SELECT* AUDIO SELECT* DEVICE DELETE PIN CODE EDIT (0000)
RECONNECT AUTO PAIRING
Default: XX
Selects the phone or audio device to connect or disconnect. " " appears in front of the device name when connected. " " appears in front of the current playback audio device.
1 Turn the volume knob to select a device to delete, then press the knob. 2 Turn the volume knob to select [YES] or [NO], then press the knob.
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press
to move the entry position.
Repeat steps 1 and 2 until you finish entering the PIN code.
3 Press the volume knob to confirm.
ON: The unit automatically reconnect when the last connected Bluetooth device is within range. ; OFF: Cancels.
ON: The unit automatically pair supported Bluetooth device (iPhone/iPod touch/Android device) when it is connected through USB input terminal. Depending on the operating system of the connected device, this function may not work. ; OFF: Cancels.
20
INITIALIZE INFORMATION
YES: Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.). ; NO: Cancels.
MY BT NAME: Displays the unit name ("KD-R9 BTS"/"KD-R8 BTS"/"KD-R7 BT"/ "KD-RD9 BTS"/"KD-RD7 BT"/"KD-R9 MBS"). ; MY ADDRESS: Shows address of this unit.
* You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit. · Make sure there is no Bluetooth device paired.
1 Press and hold
.
"BLUETOOTH" "CHECK MODE" appears. "SEARCH
NOW USING PHONE" "PIN IS 0000" scrolls on the
display.
2 Search and select "KD-R9 BTS"/"KD-R8 BTS"/
"KD-R7 BT"/"KD-RD9 BTS"/"KD-RD7 BT"/
"KD-R9 MBS" on the Bluetooth device within
3 minutes.
3 Perform (A), (B) or (C) depending on what appears
on the display.
(A) "PAIRING" "XXXXXX" (6-digit passkey): Ensure
that the same passkey appears on the unit and
Bluetooth device, then operate the Bluetooth
device to confirm the passkey.
(B) "PAIRING" "PIN IS 0000": Enter "0000" on the
Bluetooth device.
(C) "PAIRING": Operate the Bluetooth device to
confirm pairing.
BLUETOOTH®
After pairing is successful, "PAIRING OK" "[Device Name]" appears and Bluetooth
compatibility check starts. If "CONNECT NOW USING PHONE" appears, operate the Bluetooth device to allow phonebook access to continue. "TESTING" flashes on the display.
The connectivity result flashes on the display. "PAIRING OK" and/or "HANDS-FREE OK"*1 and/ or "AUD.STREAM OK"*2 and/or "PBAP OK"*3 : Compatible
*1 Compatible with Hands-Free Profile (HFP) *2 Compatible with Advanced Audio Distribution Profile (A2DP) *3 Compatible with Phonebook Access profile (PBAP)
After 30 seconds, "PAIRING DELETED" appears to indicate that pairing has been deleted, and the unit exits check mode.
· To cancel, press and hold
to turn off the
power, then turn on the power again.
BLUETOOTH -- Audio
While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.
Audio player via Bluetooth
1 Press
repeatedly to select BT AUDIO (or press SOURCE on the remote control).
· Pressing enters BT AUDIO directly.
2 Operate the Bluetooth audio player to start playback.
To
On the faceplate
On the remote control
Playback/pause
Press the volume knob.
Press .
Select group or folder
Press
.
Press .
Reverse skip/Forward skip Press
.
Press .
Reverse/Fast-forward
Press and hold
.
Press and hold .
Repeat play
Press repeatedly. TRACK REPEAT, ALL REPEAT, REPEAT OFF
( Not available )
Random play
Press repeatedly. ( Not available )
GROUP RANDOM, ALL RANDOM, RANDOM OFF
Select a file from a folder/ Refer to "Select a file from a folder/list"
list
on page 9.
Switch between connected Press 5.* Bluetooth audio devices
( Not available ) ( Not available )
* Pressing the "Play" key on the connected device itself also causes switching of sound output from the device.
Operations and display indications may differ according to their availability on the connected device.
21
BLUETOOTH®
Settings to use JVC Remote application JVC Remote application is designed to control the JVC car receiver's operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).
Preparation: Install the latest version of JVC Remote application on your device before connecting.
1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the
knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press
to exit.
To return to the previous setting item, press
.
Default: XX
REMOTE APP
SELECT Select the device (IOS or ANDROID) to use the application.
IOS
YES: Selects iPhone/iPod to use the application via Bluetooth or connected via USB input
terminal. ; NO: Cancels.
If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input
terminal) to activate the application.
· The connectivity of the application will be interrupted or disconnected if:
You change from iPod BT source to any playback source connected via the USB input terminal.
You change from iPod USB source to iPod BT source.
ANDROID YES: Selects Android smartphone to use the application via Bluetooth. ; NO: Cancels.
ANDROID LIST*
Selects the Android smartphone to use from the list.
* Displayed only when [ANDROID] of [SELECT] is set to [YES].
STATUS
Shows the status of the selected device. IOS CONNECTED: You are able to use the application using the iPhone/iPod connected via Bluetooth or USB input terminal. IOS NOT CONNECTED: No IOS device is connected to use the application. ANDROID CONNECTED: You are able to use the application using the Android smartphone connected via Bluetooth. ANDROID NOT CONNECTED: No Android device is connected to use the application.
Listen to iPhone/iPod via Bluetooth
You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.
Press
repeatedly to select iPod BT.
· You can operate the iPod/iPhone in the same way as
iPod/iPhone via USB input terminal. ( 8)
· If you plug in an iPhone/iPod to the USB input
terminal while listening to iPod BT source, the source
automatically change to iPod USB. Press
to select
iPod BT if the device is still connected via Bluetooth.
22
BLUETOOTH®
Internet radio via Bluetooth
You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the iPhone/iPod touch/Android device via Bluetooth on this unit. · Make sure the USB input terminal is not connected to any device.
Listen to Pandora (except KD-R792BT)
Preparation: Select [ON] for [PANDORA SRC] in [SOURCE SELECT]. ( 4)
1 Open the Pandora application on your device.
2 Connect your device via Bluetooth connection. ( 16)
3 Press
repeatedly to select PANDORA (for iPhone/iPod) or
PANDORA BT (for Android device).
The source switches and broadcast starts automatically.
· You can operate Pandora in the same way as Pandora via USB input terminal. ( 10)
Listen to iHeartRadio (except KD-R792BT)
Preparation: Select [ON] for [IHEART SRC] in [SOURCE SELECT]. ( 4)
1 Open the iHeartAuto application on your device.
2 Connect your device via Bluetooth connection. ( 16)
3 Press
repeatedly to select IHEARTRADIO.
The source switches and broadcast starts automatically.
· You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal. ( 11)
Listen to Spotify
Preparation: Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. ( 4)
1 Open the Spotify application on your device.
2 Connect your device via Bluetooth connection. ( 16)
3 Press
repeatedly to select SPOTIFY (for iPhone/iPod) or
SPOTIFY BT (for Android device).
The source switches and broadcast starts automatically.
· You can operate Spotify in the same way as Spotify via USB input terminal. ( 12)
23
AUX
Use a portable audio player
1 Connect a portable audio player (commercially available).
3.5 mm (1/8") stereo mini plug with "L" shaped connector (commercially available)
Portable audio player
Auxiliary input jack
2 Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. ( 4)
3 Press
repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio output.
24
AUDIO SETTINGS
1 Press and hold .
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press
to exit.
To return to the previous setting item, press
.
Default: XX
EQ SETTING
PRESET EQ
Select a preset equalizer suitable to the music genre. · Select [USER] to use the settings made in [EASY EQ] or [PRO EQ]. FLAT/DRVN 3/DRVN 2/DRVN 1/HARD ROCK/HIP HOP/JAZZ/POP/R&B/ USER/CLASSICAL Drive equalizer (DRVN 3/DRVN 2/DRVN 1) boosts specific frequencies in the audio signal to reduce the noise heard from outside the car or running noise of the tyres.
EASY EQ
Adjust your own sound settings.
· The settings are stored to [USER].
· The settings made may affect the current settings of [PRO EQ].
SUB.W SP*1*2: 00 to +06
(Default: +03
SUB.W *1*3:
50 to +10
00
BASS:
LVL09 to LVL+09
LVL 00
MID:
LVL09 to LVL+09
LVL 00
TRE:
LVL09 to LVL+09
LVL 00)
*1, *2, *3: ( 25)
AUDIO SETTINGS
PRO EQ
Adjust your own sound settings. · The settings are stored to [USER]. · The settings made may affect the current settings of [EASY EQ].
62.5HZ
LEVEL 09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)
ON: Turns on the extended bass. ; OFF: Cancels.
100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ/ 16kHZ
LEVEL 09 to LEVEL +09 (LEVEL 00): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)
Q FACTOR
1.35/1.50/2.00: Adjust the quality factor.
AUDIO CONTROL
BASS BOOST
LEVEL +01 to LEVEL +05: Selects your preferred bass boost level. ; OFF: Cancels.
LOUDNESS
LEVEL 01/LEVEL 02: Boosts low or high frequencies to produce a wellbalanced sound at low volume. ; OFF: Cancels.
SUB.W LEVEL*1 SPK-OUT*2
(Not applicable when 3-way crossover is selected.) SUB.W 00 to SUB.W +06 (SUB.W +03): Adjusts the output level of the subwoofer connected via speaker lead. ( 42)
PRE-OUT *3
SUB.W 50 to SUB.W +10 (SUB.W 00): Adjusts the output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier. ( 43)
SUBWOOFER ON: Turns on the subwoofer output. ; OFF: Cancels. SET *3
FADER
(Not applicable when 3-way crossover is selected.) POSITION R15 to POSITION F15 (POSITION 00): Adjusts the front and rear speaker output balance.
BALANCE *4
POSITION L15 to POSITION R15 (POSITION 00): Adjusts the left and right speaker output balance.
VOLUME ADJUST LEVEL 15 to LEVEL +06 (LEVEL 00): Preset the initial volume level of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust.
AMP GAIN
LOW POWER: Limits the maximum volume level to 25. (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speakers.) ; HIGH POWER: The maximum volume level is 35.
SPK/PRE OUT
(Not applicable when 3-way crossover is selected.) Depending on the speaker connection method, select the appropriate setting to get the desired output. ( 26, Speaker output settings)
SPEAKER SIZE X ' OVER
Depending on the crossover type you have selected ( [X ' OVER TYPE]), 2-way crossover or 3-way crossover setting items will be shown. ( 27, Crossover settings) By default, 2-way crossover type is selected.
DTA SETTINGS CAR SETTINGS X ' OVER TYPE
For settings, 28, Digital Time Alignment settings.
Caution: Adjust the volume before changing the [X ' OVER TYPE] to avoid the sudden increase or decrease of the output level.
2-WAY 3-WAY
(Displayed only when [3-WAY] is selected.) YES: Selects two way crossover type. ; NO: Cancels.
(Displayed only when [2-WAY] is selected.) YES: Selects three way crossover type. ; NO: Cancels.
*1 Displayed only when [SUBWOOFER SET] is set to [ON]. *2 For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].
( 26) *3 For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or
[SUB.W/SUB.W]. ( 26) *4 This adjustment will not affect the subwoofer output.
25
AUDIO SETTINGS
SOUND EFFECT SPACE ENHANCE
SND RESPONSE SOUND LIFT VOL LINK EQ K2 TECHNOLOGY
(Not applicable for TUNER source.) SMALL/MEDIUM/LARGE: Virtually enhances the sound space. ; OFF: Cancels.
LEVEL1/LEVEL2/LEVEL3: Virtually makes the sound more realistic. ; OFF: Cancels.
LOW/MIDDLE/HIGH: Virtually adjust the sound position heard from the speakers. ; OFF: Cancels.
ON: Boosts the frequency to reduce the noise heard from outside the car or running noise of the tyres. ; OFF: Cancels.
(Not applicable for TUNER source, SIRIUS XM source and AUX source.) ON: Improve the sound quality of compressed music. ; OFF: Cancels.
Speaker output settings [SPK/PRE OUT]
(Applicable only if [X ' OVER TYPE] is set to [2-WAY]) ( 25) Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method.
Connection via lineout terminals For connections through an external amplifier. ( 43) KD-R995BTS/KD-R895BTS/KD-R99MBS:
Setting on [SPK/PRE OUT]
Audio signal through lineout terminal
FRONT
REAR
SW
REAR/REAR (default) Front speakers output
Rear speakers output
Subwoofer output
REAR/SUB.W
( Not available )
( Not available )
( Not available )
SUB.W/SUB.W
Front speakers output
L (left): Subwoofer output Subwoofer output R (right): (Mute)
26
KD-R990BTS/KD-R792BTKD-RD99BTS:
Setting on [SPK/PRE OUT]
REAR/REAR REAR/SUB.W (default) SUB.W/SUB.W
Audio signal through lineout terminal
FRONT
REAR/SW
Front speakers output
Rear speakers output
Front speakers output
Subwoofer output
Front speakers output
Subwoofer output
KD-R790BT/KD-RD79BT:
Setting on [SPK/PRE OUT]
REAR/REAR REAR/SUB.W (default) SUB.W/SUB.W
Audio signal through lineout terminal REAR/SW
Rear speakers output Subwoofer output Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with this settings you can also enjoy the subwoofer output. ( 42)
Setting on [SPK/PRE OUT]
REAR/REAR REAR/SUB.W
Audio signal through rear speaker lead
L (left)
R (right)
Rear speakers output
Rear speakers output
Rear speakers output
Rear speakers output
SUB.W/SUB.W
Subwoofer output
(Mute)
If [SUB.W/SUB.W] is selected: [120HZ] is selected in [SUBWOOFER LPF] and [THROUGH] is not available. [POSITION R02] is selected in [FADER] and selectable range is [POSITION
R15] to [POSITION 00].
AUDIO SETTINGS
Crossover settings
Below are the available setting items for 2-way crossover and 3-way crossover.
Caution Select a crossover type according to how the speakers are connected. ( 42, 43) If you select a wrong type: · The speakers may damage. · The output sound level may be extremely high or low.
SPEAKER SIZE Selects according to the connected speaker size for optimum performance. · The frequency and slope settings are automatically set for the
crossover of the selected speaker. · When 2-way crossover is selected, if [NONE] is selected for [TWEETER] of
[FRONT], [REAR] and [SUBWOOFER] for [SPEAKER SIZE], the [X ` OVER] setting of the selected speaker is not available. · When 3-way crossover is selected, if [NONE] is selected for [WOOFER] of [SPEAKER SIZE], the [X ` OVER] setting of [WOOFER] is not available.
X ` OVER (crossover) · [FRQ]/[F-HPF FRQ]/[R-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]: Adjusts
the crossover frequency for the selected speakers (high pass filter or low pass filter). If [THROUGH] is selected, all signals are sent to the selected speakers. · [SLOPE]/[F-HPF SLOPE]/[R-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/ [LPF SLOPE]: Adjusts the crossover slope. Selectable only if a setting other than [THROUGH] is selected for the crossover frequency. · [SW LPF PHASE]/[PHASE]: Selects the phase of the speaker output to be in line with the other speaker output. · [GAIN LEFT]/[GAIN RIGHT]/[F-HPF GAIN]/[R-HPF GAIN]/[SW LPF GAIN]/[GAIN]: Adjusts the output volume of the selected speaker.
2-way crossover setting items
SPEAKER SIZE
FRONT
SIZE
3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/
6×9/7×10
TWEETER
SMALL/MIDDLE/LARGE/NONE (not connected)
REAR *1
3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10/ NONE (not connected)
SUBWOOFER*2*3 6.5"/8"/10"/12"/15" OVER/NONE (not connected)
X ' OVER
TWEETER
FRQ
1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/ 10KHZ/12.5KHZ
GAIN LEFT 08DB to 00DB
GAIN RIGHT 08DB to 00DB
FRONT HPF
F-HPF FRQ
30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH
F-HPF SLOPE 06DB/12DB/18DB/24DB
REAR HPF*1
F-HPF GAIN R-HPF FRQ
08DB to 00DB
30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH
R-HPF SLOPE 06DB/12DB/18DB/24DB
R-HPF GAIN 08DB to 00DB
SUBWOOFER LPF *2*3
SW LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH
SW LPF SLOPE 06DB/12DB/18DB/24DB
SW LPF PHASE REVERSE (180°)/ NORMAL (0°)
SW LPF GAIN 08DB to 00DB
*1, *2, *3: ( 28)
27
AUDIO SETTINGS
3-way crossover setting items
SPEAKER SIZE
TWEETER SMALL/MIDDLE/LARGE
MID RANGE 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9
WOOFER*3 6.5"/8"/10"/12"/15" OVER/NONE (not connected)
X ' OVER
TWEETER HPF FRQ 1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/10KHZ/12.5KHZ
SLOPE 06DB/12DB
PHASE REVERSE (180°)/NORMAL (0°)
GAIN
08DB to 00DB
MID RANGE HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/120HZ/ 150HZ/180HZ/220HZ/250HZ/THROUGH
HPF SLOPE 06DB/12DB
LPF FRQ 1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/ 10KHZ/12.5KHZ/THROUGH
LPF SLOPE 06DB/12DB
PHASE REVERSE (180°)/NORMAL (0°)
GAIN WOOFER*3 LPF FRQ
08DB to 00DB
30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/120HZ/ 150HZ/180HZ/220HZ/250HZ/THROUGH
SLOPE 06DB/12DB
PHASE REVERSE (180°)/NORMAL (0°)
GAIN
08DB to 00DB
*1 Displayed only when [SPK/PRE OUT] is set to [REAR/REAR] or [REAR/SUB.W]. ( 26) *2 Except KD-R995BTS/KD-R895BTS/KD-R99MBS: Displayed only when [SPK/PRE OUT] is set to
[REAR/SUB.W] or [SUB.W/SUB.W]. ( 26) *3 Displayed only when [SUBWOOFER SET] is set to [ON]. ( 25)
28
Digital Time Alignment settings
Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle. · For more information, 29, Determining the value for [DISTANCE]
and [GAIN] of [DTA SETTINGS].
DTA SETTINGS POSITION
DISTANCE *1 GAIN*1 DTA RESET CAR SETTINGS CAR TYPE R-SP LOCATION*2
*1, *2: ( 29)
Selects your listening position (reference point). ALL: Not compensating ; FRONT RIGHT: Front right seat ; FRONT LEFT: Front left seat ; FRONT ALL: Front seat · [FRONT ALL] is displayed only when [X ' OVER TYPE] is
set to [2-WAY]. ( 25)
0FT to 20.01FT: Fine adjust the distance to compensate.
8DB to 0DB: Fine adjust the output volume of the selected speaker.
YES: Resets the settings ([DISTANCE] and [GAIN]) of the selected [POSITION] to default. ; NO: Cancels.
Identify your car type and rear speaker location in order to make the adjustment for [DTA SETTINGS].
COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV/ MINIVAN(LONG): Selects the type of vehicle. ; OFF: Not compensating.
Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point). · DOOR/REAR DECK: Selectable only when [CAR TYPE]
is selected as [OFF], [COMPACT], [FULL SIZE CAR], [WAGON] or [SUV]. · 2ND ROW/3RD ROW: Selectable only when [CAR TYPE] is selected as [MINIVAN] or [MINIVAN(LONG)].
AUDIO SETTINGS
Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS]
If you specify the distance from the center of the currently set listening position to every speaker, the delay time will be automatically computed and set. 1 Determine the center of the currently set
listening position as the reference point. 2 Measure the distances from the reference
point to the speakers. 3 Calculate the differences between the distance
of the furthest speaker (rear speaker) and other speakers. 4 Set the [DISTANCE] calculated in step 3 for individual speakers. 5 Adjust [GAIN] for individual speakers.
Example: When [FRONT ALL] is selected as the listening position
*1 Before making an adjustment, select the speaker: When 2-way crossover is selected: FRONT LEFT/FRONT RIGHT/REAR LEFT/REAR RIGHT/SUBWOOFER: [REAR LEFT], [REAR RIGHT] and [SUBWOOFER] is selectable only if a setting other than [NONE] is selected for [REAR] and [SUBWOOFER] of [SPEAKER SIZE]. ( 27)
When 3-way crossover is selected: TWEETER LEFT/TWEETER RIGHT/MID LEFT/MID RIGHT/WOOFER: [WOOFER] is selectable only if a setting other than [NONE] is selected for [WOOFER] of
[SPEAKER SIZE]. ( 28) *2 Displayed only when [X ' OVER TYPE] is set to [2-WAY] ( 25) and if a setting other
than [NONE] is selected for [REAR] of [SPEAKER SIZE]. ( 27)
DISPLAY SETTINGS
Zone identification for brightness setting
KD-R995BTS/KD-R990BTS/KD-R895BTS/ KD-RD99BTS
KD-R792BT/KD-R790BT/KD-RD79BT/ KD-R99MBS
Zone identification for color setting
KD-R995BTS/KD-R990BTS/KD-R895BTS/ KD-RD99BTS
KD-R99MBS
1 Press and hold .
2 Turn the volume knob to select an item ( 30), then press the
knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press
to exit.
To return to the previous setting item, press
.
29
DISPLAY SETTINGS
Default: XX
DISPLAY
DIMMER
Dim the illumination. OFF: Dimmer is turned off. Brightness changes to [DAY] setting. ON: Dimmer is turned on. Brightness changes to [NIGHT] setting. ( [BRIGHTNESS]) DIMMER TIME: Set the dimmer on and off time. 1 Turn the volume knob to adjust the [ON] time, then press the knob. 2 Turn the volume knob to adjust the [OFF] time, then press the knob.
(Default: [ON]: PM6:00 ; [OFF]: AM6:00) DIMMER AUTO: Dimmer turns on and off automatically when you turn off or on the car headlights.*1
BRIGHTNESS
Set the brightness for day and night separately. 1 DAY/NIGHT: Select day or night. 2 Select a zone. ( 29) 3 LEVEL 00 to LEVEL 31: Set the brightness level.
TEXT SCROLL*2 SCROLL ONCE: Scrolls the display information once. ; SCROLL AUTO: Repeats scrolling at 5-second intervals. ; SCROLL OFF: Cancels.
COLOR (for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS)
PRESET
Select illumination colors for the buttons on different zones separately. 1 Select a zone. ( 29) 2 Select a color for the selected zone.
· COLOR 01 to COLOR 49 · USER: The color you have created for [DAY COLOR] or [NIGHT COLOR]
is shown. · COLOR FLOW01 to COLOR FLOW03: Color changes at different
speeds. · CRYSTAL/FLOWER/FOREST/GRADATION/OCEAN/SUNSET/
RELAX: The selected color pattern is shown.*3 (Selectable only when [ALL ZONE] is selected in step 1.)
DAY COLOR NIGHT COLOR
Store your own day and night illumination colors for different zones. 1 Select a zone. ( 29) 2 RED/GREEN/BLUE: Select a primary color. 3 00 to 31: Select the level. Repeat steps 2 and 3 for all the primary colors. · Your setting is stored to [USER] in [PRESET]. · [NIGHT COLOR] or [DAY COLOR] is changed by turning on or off your
car's headlight.
COLOR GUIDE ON: Changes the button illumination when settings are performed on menu and list search. ; OFF: Cancels.
COLOR (for KD-R99MBS)
PRESET
Select illumination colors for the buttons. · COLOR 01 to COLOR 49 · USER: The color you have created for [DAY COLOR] or
[NIGHT COLOR] is shown. · COLOR FLOW01 to COLOR FLOW03: Color changes at different
speeds.
DAY COLOR NIGHT COLOR
Store your own day and night illumination colors for the buttons. 1 RED/GREEN/BLUE: Select a primary color. 2 00 to 31: Select the level. Repeat steps 1 and 2 for all the primary colors. · Your setting is stored to [USER] in [PRESET]. · [NIGHT COLOR] or [DAY COLOR] is changed by turning on or off your
car's headlight.
*1, *2, *3: ( 31)
30
DISPLAY SETTINGS
MENU COLOR
ON: The color of button illumination changes to white color when in menu mode or when selecting a music file from a folder/list.; OFF: Cancels.
*1 The illumination control wire connection is required. ( 42)
*2 Some characters or symbols will not be shown correctly (or will be blanked).
*3 If one of these color pattern is selected, the [ZONE 1] and [ZONE 2] illumination colors will change to the default colors.
LEARNING STEERING REMOTE CONTROL (for KD-R792BT)
You can control the unit with the steering remote control keys on your vehicle. After connection, you can configure the control keys according to your preference. · You can only make this configuration if your vehicle is equipped with the electrical steering
remote control. · If the steering remote control in your car is not compatible, configuration may not be completed
and an error message may appear. ( 36)
Make the connection
Steering remote cable (supplied)
Gray/red
Learning steering remote input terminal
Rear panel
Bright green/red Purple/red
Connect to your vehicle's steering remote harness. Contact your JVC dealer for details.
Configure the control keys
1 Press and hold . 2 Turn the volume knob to select [SYSTEM], then press the knob. 3 Turn the volume knob to select [USER S.REMO], then press the knob. 4 Turn the volume knob to select [SET KEY], then press the knob.
A key list of 16 assignable keys appears. · K## NONE: No function has been assigned. 5 Turn the volume knob to select any key from the key list to assign the function, then press the knob. "PRESS KEY TO ASSIGN K##" appears.
31
LEARNING STEERING REMOTE CONTROL (for KD-R792BT)
6 Press and hold any control keys on your steering remote control which
you want to assign.
A list of key functions will appear on the display.
NONE (default)/MUTE/SEEK UP/SEEK DOWN/VOL UP/VOL DOWN/MODE/ON HOOK/
OFF HOOK/VOICE/ENTER
7 Turn the volume knob to select a function to assign, then press the knob.
The selected key function is assigned to the steering remote control key you
have selected in step 6.
The display returns to the key list as on step 4.
· K## (Function): When certain function has been assigned to a key.
8 Repeat steps 5, 6 and 7 to assign other control keys.
9 Press
to exit.
To reassign the control keys
1 Press and hold . 2 Turn the volume knob to select [SYSTEM], then press the knob. 3 Turn the volume knob to select [USER S.REMO], then press the knob. 4 Turn the volume knob to select [RESET KEY], then press the knob. 5 Turn the volume knob to select [YES], then press the knob.
All the control keys will be reset. Selecting [NO] will cancel the operation.
When [FACTORY RESET] is set to [YES] ( 5), it will also reset the learning remote control.
To return to the previous setting item, press
.
REFERENCES
Maintenance Cleaning the unit Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector
Detach the faceplate and clean the
connector gently with a cotton swab, being
careful not to damage the connector.
Connector (on the reverse
Handling discs:
side of the faceplate)
· Do not touch the recording surface of the disc.
· Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
· Do not use any accessories for the disc.
· Clean from the center of the disc and move outward.
· Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
· When removing discs from this unit, pull them out horizontally.
· Remove burrs from the center hole and disc edge before inserting a disc.
More information For: Latest firmware updates and latest compatible item list
JVC original application Any other latest information
General · This unit can only play the following CDs:
· DualDisc playback: The Non-DVD side of a "DualDisc" does not comply with the "Compact Disc Digital Audio" standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended.
32
REFERENCES
Playable files · Playable audio file:
For disc: MP3 (.mp3), WMA (.wma), AAC (.aac) For USB mass storage class device:
MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.flac) · Playable disc media: CD-R/CD-RW/CD-ROM · Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name. · Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device. The AAC (.m4a) file in a CD encoded by iTunes cannot be played on this unit.
Unplayable discs · Discs that are not round. · Discs with coloring on the recording surface or discs that are dirty. · Recordable/ReWritable discs that have not been finalized. · 8 cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices · You cannot connect a USB device via a USB hub. · Connecting a cable whose total length is longer than 5 m may result in abnormal playback. · This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1.5 A.
About iPod/iPhone · Via USB input terminal:
Made for iPod touch (5th and 6th generation) iPod nano (7th generation) iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus · Via Bluetooth: Made for iPod touch (5th and 6th generation) iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus · It is not possible to browse video files on the "Videos" menu in [HEAD MODE]. · The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.
· Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit.
About Android device · This unit supports Android OS 4.1 and above. · Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
(AOA) 2.0. · If the Android device supports both mass storage class device and AOA 2.0, this unit always
playback via AOA 2.0 as priority.
About Pandora · Pandora is only available in certain countries.
· Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
· Some functions of Pandora cannot be operated from this unit.
About iHeartRadio · iHeartRadio® is a third-party service, therefore the specifications are subject to change
without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable. · Some iHeartRadio® functionality cannot be operated from this unit.
About Spotify · Spotify application supports:
iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus (iOS 8 or above) iPod touch (5th and 6th generation) Android OS 4.0.3 or above · Spotify is a third party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable. · Some functions of Spotify cannot be operated from this unit.
33
REFERENCES
About Bluetooth · Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit. · This unit may not work with some Bluetooth devices. · Signal conditions vary, depending on the surroundings.
Change the display information Each time you press , the display information changes. · If the information is unavailable or not recorded, "NO TEXT", "NO NAME", or other information (eg. station name) appears or display will be blank.
Source name FM or AM
CD or USB FRONT/ USB REAR/USB
iPod FRONT/iPod REAR/ iPod USB/iPod BT or ANDROID FRONT/ ANDROID REAR/ANDROID *1, *2, : ( 35)
Display information
KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS
KD-R792BT/KD-R790BT/KD-RD79BT
Frequency (Date/Clock)*1 Frequency (Date) with music synchronisation*2 (back to the Frequency Clock Frequency with music synchronisation*2
beginning)
(back to the beginning)
(For FM Radio Broadcast Data System stations only)
(For FM Radio Broadcast Data System stations/FM Radio
Station name (PS)/Program type (PTY) (Date/Clock)*1 Radio text (Date/Clock)*1
Data signal only)
Radio text+ (Radio text+) Song title (Artist) Song title (Date/Clock)*1 Frequency Station name (PS)/Program type (PTY) Radio text
(Date/Clock)*1 Station name (PS)/Program type (PTY) (Date) with music synchronisation*2 Radio text+ Radio text+ title/Radio text+ artist Frequency
(back to the beginning)
Clock Station name (PS)/Program type (PTY) with music
synchronisation*2 (back to the beginning)
(For CD-DA)
(For CD-DA)
Track title (Artist) Track title (Disc name) Track title (Date/Clock)*1 Playing time (Date/ Disc title/Artist Track title/Artist Playing time Clock
Clock)*1 Track title (Artist) with music synchronisation*2 (back to the beginning)
Disc title/Artist with music synchronisation*2 (back to the
beginning)
(For MP3/WMA/AAC/WAV/FLAC files)
(For MP3/WMA/AAC/WAV/FLAC files)
Song title (Artist) Song title (Album name) Song title (Date/Clock)*1 File name (Folder Song title/Artist Album name/Artist Folder name
name) File name (Date/Clock)*1 Playing time (Date/Clock)*1 Song title (Artist) with File name Playing time Clock Song title/Artist with
music synchronisation*2 (back to the beginning)
music synchronisation*2 (back to the beginning)
When [HEAD MODE]/[AUTO MODE] is selected ( 9): Song title (Artist) Song title (Album name) Song title (Date/Clock)*1 Playing time (Date/Clock)*1 Song title (Artist) with music synchronisation*2 (back to the beginning)
When [HEAD MODE]/[AUTO MODE] is selected ( 9): Song title/Artist Album name/Artist Playing time Clock Song title/Artist with music synchronisation*2 (back to the beginning)
34
REFERENCES
Source name
Display information KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS
KD-R792BT/KD-R790BT/KD-RD79BT
PANDORA FRONT/
Station name (Date/Clock)*1 Shared/Radio (Date/Clock)*1 Song title (Artist) Song title Station name Shared/Radio Song title Artist name
PANDORA REAR/PANDORA/ (Album name) Song title (Date/Clock)*1 Playing time (Date/Clock)*1 Station name Album name Playing time Clock Station name with music
PANDORA BT
(Date) with music synchronisation*2 (back to the beginning)
synchronisation*2 (back to the beginning)
IHEARTRADIO-F/ IHEARTRADIO-R/ IHEARTRADIO
Station name (Date/Clock)*1 Song title (Artist) Song title (Date/Clock)*1 Station name Station name Song title/Artist Clock Station name with
(Date) with music synchronisation*2 (back to the beginning)
music synchronisation*2 (back to the beginning)
SPOTIFY FRONT/ SPOTIFY REAR/SPOTIFY/ SPOTIFY BT
Context title (Date/Clock)*1 Song title (Artist) Song title (Album name) Song title (Date/Clock)*1 Playing Time (Date/Clock)*1 Context title (Date) with music synchronisation*2 (back to the beginning)
Context title Song title Artist name Album name Playing Time Clock Context title with music
synchronisation*2 (back to the beginning)
SIRIUS XM
Channel number (Status) Channel name (Status) Artist (Status) Song title (Status)
Content information (Status) Category name (Status) Date (Status) Channel number
--
(Status) with music synchronisation*2 (back to the beginning)
BT AUDIO
Song title (Artist) Song title (Album name) Song title (Date/Clock)*1 Playing time Song title/Artist Album name/Artist Playing time Clock (Date/Clock)*1 Song title (Artist) with music synchronisation*2 (back to the beginning) Song title/Artist with music synchronisation*2 (back to the
beginning)
AUX
AUX (Date/Clock)*1 AUX (Date) with music synchronisation*2 (back to the beginning) AUX Clock AUX with music synchronisation*2 (back to
the beginning)
*1 Battery and signal strength of the Bluetooth device will be shown if [BATT/SIGNAL] is set to [AUTO]. ( 19) *2 For KD-R995BTS/KD-R990BTS/ KD-R895BTS/KD-RD99BTS/KD-R99MBS: The color of the button illumination changes and synchronises with the music.
For KD-R792BT/KD-R790BT/KD-RD79BT: The brightness of the button illumination changes and synchronises with the music.
35
TROUBLESHOOTING
Symptom
Remedy
Sound cannot be heard.
· Adjust the volume to the optimum level. · Check the cords and connections.
"MISWIRING CHECK WIRING THEN PWR ON" appears.
Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.
General
"PROTECTING SEND SERVICE" appears.
Send the unit to the nearest service center.
Source cannot be selected. Check the [SOURCE SELECT] setting. ( 4)
"ERROR"/ "FAIL" (For KD-R792BT)
Your steering remote controller is not compatible, learning may not be completed. Consult your car audio dealer for details.
Radio
· Radio reception is poor. · Static noise while
listening to the radio.
Connect the antenna firmly.
Disc cannot be ejected.
Press and hold to forcibly eject the disc. Be careful not to drop the disc when it is ejected.
"IN DISC" appears.
Make sure nothing is blocking the loading slot when you eject the disc.
"PLEASE EJECT" appears.
Press , then insert the disc correctly.
CD/USB/iPod
Playback order is not as intended.
The playback order is determined by the file name (USB) or the order in which files were recorded (disc).
Elapsed playing time is not This depends on the recording process earlier. correct.
"NOT SUPPORT" appears and track skips.
Check whether the track is a playable format. ( 32, 33)
"READING" keeps flashing. · Do not use too many hierarchical levels and folders. · Reload the disc or reattach the USB device.
Symptom
Remedy
"UNSUPPORTED DEVICE" appears.
· Check whether the connected device is compatible with this unit and ensure the file systems are in supported formats. ( 32, 33)
· Reattach the device.
"UNRESPONSIVE DEVICE" appears.
Make sure the device is not malfunction and reattach the device.
"USB HUB IS NOT SUPPORTED" appears.
This unit cannot support a USB device connected via a USB hub.
"CANNOT PLAY" appears. Connect a USB device that contains playable audio files.
CD/USB/iPod
· The source does not change to "USB" when you connect a USB device while listening to another source.
· "USB ERROR" appears
The USB port is drawing more power than the design limit. Turn the power off and unplug the USB device. Then, turn on the power and reattach the USB device. If this does not solve the problem, turn the power off and on (or reset the unit) before replacing with another USB device.
The iPod/iPhone does not · Check the connection between this unit and iPod/ turn on or does not work. iPhone.
· Disconnect and reset the iPod/iPhone using hard reset.
"LOADING" appears when
you enter search mode by
pressing
.
This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later.
Correct characters are not displayed.
· This unit can only display uppercase letters, numbers, and a limited number of symbols.
· Depending on the display language you have selected ( 5), some characters may not be displayed correctly.
36
TROUBLESHOOTING
Symptom
Remedy
· Sound cannot be heard during playback.
· Sound output only from the Android device.
· Reconnect the Android device. · If in [AUDIO MODE], launch any media player application
on the Android device and start playback. · If in [AUDIO MODE], relaunch the current media player
application or use another media player application. · Restart the Android device. · If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit. ( 33)
ANDROID
Cannot playback at [AUTO MODE].
· Make sure JVC MUSIC PLAY APP is installed on the Android device. ( 8)
· Reconnect the Android device and select the appropriate control mode. ( 9)
· If this does not solve the problem, the connected Android device does not support [AUTO MODE]. ( 33)
"NO DEVICE" or "READING" keeps flashing.
· Switch off the developer options on the Android device. · Reconnect the Android device. · If this does not solve the problem, the connected Android
device does not support [AUTO MODE]. ( 33)
Playback is intermittent Turn off the power saving mode on the Android device. or sound skips.
"CANNOT PLAY"
· Make sure Android device contains playable audio files. · Reconnect the Android device. · Restart the Android device.
"ADD ERROR"
New station creation is unsuccessful.
"CHK DEVICE"
Check the Pandora application on your device.
Pandora
"NO SKIPS"
The skip limit has been reached.
"NO STATIONS"
No stations are found.
"STATION LMT"
The number of registered stations has reached its limit. Retry after deleting unnecessary stations from your device.
Symptom
Remedy
"UPGRADE APP"
Make sure you have installed the latest version of the Pandora application on your device.
"CONNECT ERR"
Communication is unstable.
Pandora
"RATING ERR"
Registration of thumbs up/thumbs down has failed due to insufficient network connectivity.
"THUMBS N/A"
Registration of thumbs up/thumbs down is not allowed.
"LICENSE ERR"
You try to access from a country which Pandora is not deliverable.
iHeartRadio
Station cannot be selected.
If "Explicit Content" in [Account Settings] is checked in the web version of iHeartRADIO, custom stations become unavailable.
"NOT CONNCTD"
Link to the application is impossible.
"DISCONNECTED"
USB is disconnected from the head unit. Please make sure the device is connected properly through USB.
Spotify
"CONNECTING"
· Connected via USB input terminal: The device is connecting to the head unit. Please wait.
· Connected via Bluetooth: The Bluetooth is disconnected. Please check Bluetooth connection and make sure both the device and unit are paired and connected.
"CHECK APP"
The Spotify application is not connected properly or user is not login. End the Spotify application and restart. Then, log in to your Spotify account.
"CH LOCKED LOCK CODE?"
The selected channel is locked. Enter the correct pass code to unlock. ( 15)
"CHAN UNSUB"
The selected channel is unsubscribed.
SiriusXM® Radio
37
TROUBLESHOOTING
Symptom "CH UNAVAIL"
Remedy The selected channel is unavailable.
SiriusXM® Radio
"CHECK ANTENNA"
"CHECK TUNER"
"NO SIGNAL" "SUBSCRIPTION UPDATED PRESS ENTER TO CONTINUE." "CODE ERROR"
"NO CONTENT" "SCAN CANCEL" No Bluetooth device is detected. Pairing cannot be made.
Echo or noise occurs.
Phone sound quality is poor.
Check that the antenna and its connection are in good condition.
Make sure the SiriusXM Vehicle Tuner is connected to the unit.
Make sure the antenna is mounted outside the vehicle.
Your subscription is updated. Press the volume knob to continue.
Make sure you have entered the correct pass code. ( 15)
There is insufficient content to start TuneScan.
TuneScan has been aborted.
· Search from the Bluetooth device again. · Reset the unit. ( 3)
· Make sure you have entered the same PIN code to both the unit and Bluetooth device.
· Delete pairing information from both the unit and the Bluetooth device, then perform pairing again. ( 16)
· Adjust the microphone unit's position. ( 16) · Check the [ECHO CANCEL] setting. ( 18)
· Reduce the distance between the unit and the Bluetooth device.
· Move the car to a place where you can get a better signal reception.
Bluetooth®
Symptom
Remedy
Sound is being interrupted · Reduce the distance between the unit and the Bluetooth
or skipped during playback audio player.
of a Bluetooth audio
· Turn off, then turn on the unit and try to connect again.
player.
· Other Bluetooth devices might be trying to connect to
the unit.
The connected Bluetooth audio player cannot be controlled.
· Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)
· Disconnect and connect the Bluetooth player again.
Bluetooth®
"PLEASE WAIT"
The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again.
"NOT SUPPORT"
The connected phone does not support Voice Recognition feature.
"ERROR"
Try the operation again. If "ERROR" appears again, check if the device supports the function you have tried.
"H/W ERROR"
Reset the unit and try the operation again. If "H/W ERROR" appears again, consult your nearest service center.
"SWITCHING NG"
The connected phones might not support phone switching feature.
38
SPECIFICATIONS
Tuner
FM Frequency Range
Usable Sensitivity (S/N = 26 dB) Quieting Sensitivity (DIN S/N = 46 dB) Frequency Response (±3 dB) Signal-to-Noise Ratio (MONO) Stereo Separation (1 kHz) AM Frequency Range
Usable Sensitivity (S/N = 20 dB)
87.9 MHz -- 107.9 MHz (200 kHz step) 87.5 MHz -- 108.0 MHz (50 kHz step) 8.2 dBf (0.71 V/75 ) 17.2 dBf (2.0 V/75 ) 30 Hz -- 15 kHz 64 dB 40 dB 530 kHz -- 1 700 kHz (10 kHz step) 531 kHz -- 1 611 kHz (9 kHz step) 29 dB (28.2 V)
Laser Diode Digital Filter (D/A) Spindle Speed Wow & Flutter Frequency Response (±1 dB) Total Harmonic Distortion (1 kHz) Signal-to-Noise Ratio (1 kHz) Dynamic Range Channel Separation MP3 Decode WMA Decode AAC Decode
GaAIAs 8 times over sampling 500 rpm -- 200 rpm (CLV) Below measurable limit 20 Hz -- 20 kHz 0.01 % 105 dB 90 dB 85 dB Compliant with MPEG-1/2 Audio Layer-3 Compliant with Windows Media Audio AAC-LC ".aac" files
CD player
Bluetooth
Auxiliary
USB
USB Standard Compatible Devices File System Maximum Supply Current Digital Filter (D/A) Converter Frequency Response (±1 dB) Signal-to-Noise Ratio (1 kHz) Dynamic Range Channel Separation MP3 Decode WMA Decode AAC Decode WAV Decode FLAC Decode
Frequency Response (±3 dB) Input Maximum Voltage Input Impedance
Version Frequency Range Output Power Maximum Communication Range Pairing Profile
USB 1.1, USB 2.0 (Full speed) Mass storage class FAT12/16/32 DC 5 V 1.5 A 24 Bit 20 Hz -- 20 kHz 105 dB 90 dB 85 dB Compliant with MPEG-1/2 Audio Layer-3 Compliant with Windows Media Audio AAC-LC ".aac", ".m4a" files Linear-PCM FLAC file, up to 24 bit/96 kHz
20 Hz -- 20 kHz 1 000 mV 30 k
Bluetooth 3.0 2.402 GHz -- 2.480 GHz +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Line of sight approx. 10 m (32.8 ft) SSP (Secure Simple Pairing) HFP1.6 (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP1.5 (Audio/Video Remote Control Profile) PBAP (Phonebook Access Profile) SPP (Serial Port Profile)
39
SPECIFICATIONS
Audio
Maximum Output Power Full Bandwidth Power (at less than 1 % THD) Speaker Impedance Preout Level/Load
Preout Impedance
50 W × 4 or 50 W × 2 + 50 W × 1 (Subwoofer = 4 ) 22 W × 4
4 -- 8 KD-R995BTS: CD/USB: 5 000 mV/10 k load KD-R895BTS/KD-R99MBS: 4 000 mV/10 k load KD-R990BTS/KD-R792BT/KD-R790BT/ KD-RD99BTS/KD-RD79BT: CD/USB: 2 500 mV/10 k load 600
General
Operating Voltage (10.5 V -- 16 V allowable) Maximum Current Consumption Operating Temperature Range Installation Size (W × H × D)
Net Weight (includes Trimplate, Mounting Sleeve)
14.4 V
10 A 10°C -- +60°C 182 mm × 53 mm × 158 mm (7-3/16" × 2-1/8" × 6-1/4") 1.2 kg (2.7 lbs)
Subject to change without notice.
INSTALLATION/CONNECTION
Warning · The unit can only be used with a 12 V DC power supply, negative ground. · Disconnect the battery's negative terminal before wiring and mounting. · Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit. · To prevent short circuit:
Insulate unconnected wires with vinyl tape. Be sure to ground this unit to the car's chassis again after installation. Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into
contact with metal parts to protect the wires.
Caution · For safety's sake, leave wiring and mounting to professionals. Consult the car audio dealer. · Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot. · Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel. · Connect speakers with a maximum power of more than 50 W. If the maximum power of
the speakers is lower than 50 W, change the [AMP GAIN] setting to avoid damaging the speakers. ( 25) · Mount the unit at an angle of less than 30º. · If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle's fuse box which provides 12 V DC power supply and is turned on and off by the ignition key. · Keep all cables away from heat dissipate metal parts. · After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. · If the fuse blows, first make sure the wires are not touching car's chassis, then replace the old fuse with one that has the same rating.
40
INSTALLATION/CONNECTION
Part list for installation
(A) Faceplate
(B) Trim plate
Installing the unit (in-dash mounting)
Do the required wiring. ( 42)
(C) Mounting sleeve
(D) Wiring harness
(E) Extraction key
Basic procedure
1 Remove the key from the ignition switch, then disconnect
the terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 42)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Press
to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds.
( 3)
Hook on the top side
Orientate the trim plate as illustrated before fitting.
Dashboard of your car
Bend the appropriate tabs to hold the sleeve firmly in place.
When installing without the mounting sleeve 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the
vehicle mounting bracket and secure the unit with screws (commercially available).
How to remove the unit
Use only the specified screws. Using wrong screws might damage the unit.
41
INSTALLATION/CONNECTION
Wiring connection
IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer.
Vehicle dashboard
Factory wiring harness (vehicle)
Antenna terminal
Fuse (10 A)
To the steering wheel remote control adapter
Light blue/yellow
Custom wiring harness (separately purchased)
Blue: To power antenna
Blue/white: To amplifier
Join the same color wires together. Blue/white: Remote (12 V 350 mA)
Orange/white: Illumination Yellow: Battery 12 V
Red: Ignition 12 V
Brown (not used) Recommended connection
Black: Ground
Gray: Front speaker/3-way crossover: Mid range speaker (right) Gray/black White: Front speaker/3-way crossover: Mid range speaker (left)
White/black Purple: Rear speaker/3-way crossover: Tweeter (right) Purple/black Green: Rear speaker*1/3-way crossover: Tweeter (left) Green/black *1
42
Separate red wire
Ignition switch Car fuse block
Make this connection if your vehicle factory wiring harness does not have "12 V ignition switch" wire.
*1 You can also connect a subwoofer speaker directly using this lead without an external subwoofer amplifier. For setting, 26.
INSTALLATION/CONNECTION
Connecting external components
KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS: MIC (Microphone input terminal) ( 16)
KD-R995BTS: USB cable (DC 5 V 1.5 A) (approx. 1.2 m/4 feet)
Connecting external amplifiers
KD-R995BTS/ KD-R895BTS/ KD-R99MBS
KD-R990BTS/ KD-R792BT/ KD-R790BT/ KD-RD99BTS KD-RD79BT
Output terminals
Output terminals
REAR
:
FRONT
:
SW
:
2-way crossover setting
Rear output Front output Subwoofer output
FRONT REAR/SW
: Front output : Rear/subwoofer output
REAR/SW
: Rear/subwoofer output
KD-R792BT: Learning steering remote ( 31)
KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS: Expansion port (12 V 500 mA) To the optional SiriusXM Vehicle Tuner (commercially available) ( 13)
KD-R792BT/KD-R790BT/KD-RD79BT: Microphone input jack ( 16)
Signal cord (not supplied)
3-way crossover setting Tweeter output Mid Range output Woofer output Mid Range output Woofer output Woofer output
JVC Amplifier*2
Remote wire (not supplied)
To remote lead (blue/white) of the wiring harness. ( 42)
*2 Firmly connect the ground wire of the amplifier to the car's chassis to avoid damaging the unit.
Learn more about car stereos on our website. 43
