Midea Oil Filled Heater Owner's Manual

Safety Instructions

• ⚠️ Warning: In order to avoid overheating, do not cover the heater.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• The heater must not be located immediately below a socket-outlet.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• This heater is filled with a precise quantity of special oil. Repairs requiring opening of oil-container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leak. When scrapping the heater, follow the regulations concerning the disposal of oil.
• ♻️ Correct Disposal of this product: This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
• This heater cannot achieve accurate temperature control of the environment, and thus cannot be used as insulation device for storage environment, items, animals and plants.

Part Figure

The oil-filled radiator has the following parts:

• Fin
• Power Switch Knob
• Thermostat Knob
• Cord wrap
• Caster assembly

Use of oil filled radiator

Follow these steps to assemble and use the caster assembly:

1. Turn the heater upside down.
2. As shown in Figure 1, align the mounting hole of one caster assembly with the screw on the caster pad plate at the end of the radiator fin. Align the other caster assembly with the screws mounted at the bottom of the control box.
3. As shown in Figure 2, tighten the two sets of caster components with four butterfly nuts. Ensure they are installed firmly, then place the heater in its desired location on the ground.

Figure 1 depicts the alignment of the caster assembly. Figure 2 illustrates tightening the caster components with butterfly nuts to the control box.

Operating Instructions

Inspection before start

1. The power cord shall not be damaged or fractured.
2. Please verify the rated current of the power socket is in line with the requirements and is equipped with a safety grounding device before use; otherwise, replace the socket.

Start and power selection

1. Start: Plug in the power. Clockwise turn the thermostat knob to the "+" mark position, then turn on the power switch. The heater will start to work.
2. Power selection: Under normal circumstances, please use the maximum power "III" gear for rapid heating. If the room temperature reaches a suitable temperature, please choose a lower power "II" or "I" gear to reduce energy consumption and prevent the room becoming overheated.

Note: To use the machine for the first time or to re-insert the socket, please pay attention to check whether the plug and the socket are fitted well.

Inspection method: Insert the power plug into the socket and start for use. After about half an hour, turn off and pull out the plug. Check whether the plug pins are hot (more than about 50 °C). Replace the socket if so, to avoid burning the plug or causing a fire due to overheating of the socket because of poor contact.

Temperature adjustment

During use, if you feel it is necessary to lower the room temperature since it is too high, you can use the following adjustment modes:

1. Turn the power switch to gear "II" or "I".
2. Counterclockwise turn the thermostat knob back by a certain angle. A position closer to the "-" mark indicates a lower set temperature.

Stop

Turn the power switch to indication point "0", and then pull out the power plug.

Movement of the heater

To move the heater, turn it off first and pull out the power plug. Then push the body to make the four casters below the body roll.

Cleaning and Maintenance Instructions

1. The electric heater should be cleaned regularly to wipe out the dust on the surface of flanges, as this may influence the radiating efficiency.
2. Disconnect electricity supply and allow the radiator to cool. Wipe out dust with a soft damp cloth. Do not use detergent or abrasives.
3. Do not scrape the surfaces of flanges with sharp hard tools, to avoid surfaces getting rusty due to damage of the paint coat.