Xblitz UNI PRO 3 Wireless Earphones

Safety Instructions

To use the earphones correctly and safely, read the instructions below. When using the set, follow the following rules:

• 1. Adjust the volume appropriately when using the earphone set.
• 2. In a situation of emergency, stop using the set to ensure your safety.
• 3. Do not use the earphones to listen to music, make or receive calls while driving a car.
• 4. Place the product and accessories out of reach of children to avoid the danger caused by improper use.
• 5. Prevent water from entering the earphones during cleaning, as this can cause sound distortion and even lead to damaging the set.
• 6. Avoid setting the volume too high, i.e. to levels where you cannot hear anything around you. If you hear a buzzing noise in your ears or feel that the volume is too high, you should immediately reduce the volume.
• 7. Stop using the earphones if you experience pronounced discomfort, irritation or other undesirable reactions.
• 8. In case of excessive overheating, stop using headphones immediately and contact an Authorized Service Center.

Main Features

• 1. Wireless music playback from your phone.
• 2. Wireless phone calls using the headset.
• 3. Practical charging case for the earphones.
• 4. Voice messages in English informing about battery status, incoming calls, disconnection of the device, etc.

Earphone Set Components

• 1. Earphones
• 2. Charging case for earphones
• 3. USB cable (for charging)
• 4. User manual
• 5. Ear tips x2

Getting Started

Pairing the Device

1. Remove the insulating tape from the earphones and place them in the charging case to charge both earphones.

   WARNING: If the set does not charge when placed in the case, please connect the USB power cord to the power port of the case.

2. After removing the earphones from the case (the markings for the left and right ear are on the earphones and inside the case. L - for the left ear, R - for the right ear), a blue LED should light up on each of them, indicating that the device has been turned on.
3. If the LED on the left earphone flashes blue and red alternately, the device is ready for pairing. Turn on BT on your phone and select Xblitz UNI PRO 3 from the list of available devices to connect to your phone. When the earphones are paired with the phone, the LEDs on them will stop blinking and the corresponding information (e.g. "The device is connected, 100% battery left") will be displayed on your phone's BT connection menu.
4. The earphones will automatically turn off when placed in the case. The device will automatically turn off after 300 seconds of inactivity.
5. When you take the earphones out of the case again, they will automatically turn on and pair with your phone.

NOTE: If pairing fails, restore the device to factory settings. To do this, turn off the earphones and then hold the function buttons on both of them for 8 seconds. Then turn on the device, the set should pair up automatically.

Button Functions

• 1. Power On/Off - holding the button on either of the earphones for 3-4 seconds will turn that earphone on or off. The blue LED indicates the device is on, and the red LED indicates it is off.
• 2. Play/Stop - a short press of the button on either earphone will turn music playback on or off.
• 3. Answer/End Phone Call - pressing the button on either earphone will answer or end a phone call.
• 4. Reject Call - holding the button for 2 seconds will reject an incoming call.
• 5. Redial Number - double-pressing the button on the left earphone will activate a connection to the last dialed number.
• 6. Change Track - double-pressing the button on the right earphone will play the next track.

Using a Single Earphone

You can connect to the phone using only one earphone, leaving the additional earphone in the charging case. The earphone will automatically connect to the phone with which the set is paired. If you want to switch from using one earphone to using both earphones – remove the other earphone from the case. The set should automatically connect both earphones to the paired phone.

Charging

To charge the earphones, place them in the case. Magnets in the case will hold the earphones in place. If charging starts successfully, the LEDs on the earphones will light up red, and the LED on the case will light up blue. When the LEDs turn off, charging is complete. To charge the battery of the case, connect it to power using a standard 5V charger with a micro USB cable. When the case is charging, its blue LED will blink.

Specifications

Warranty Card/ Complaints

The product is covered by a 24-month warranty. The terms of the guarantee can be found at: https://xblitz.pl/warranty/

Complaints should be reported using the complaint form located at: http://reklamacje.kgktrade.pl/

Details, contact and website address can be found at: www.xblitz.pl

Specifications and contents of the kit are subject to change without notice. We apologise for any inconvenience.

KGK Trade declares that this device XBLITZ UNI PRO 3 is compliant with significant requirements of directive 2014/53/EU. The text of this declaration may be found on the website: http://xblitz.pl/download/DOC/deklaracja-CE-Xblitz-uni-pro3.pdf

Manufacturer: KGK Trade sp. z o.o. sp. k. Os. Urocze 12 31-953 Cracow Poland

Made in P.R.C.

Environmental Disposal Information

The crossed-out bin symbol ? indicates that waste electrical or electronic equipment, its accessories (e.g. power supplies, cables) or components (e.g. batteries) must not be disposed of with household waste. To dispose of the equipment or its components (e.g. batteries), take the equipment to the collection point where it will be accepted free of charge. Disposal is subject to the recast WEEE Directive (2012/19 / EU) and the Batteries and Accumulators Directive (2006/66 / EC). Proper disposal of the equipment prevents environmental damage. Information on collection points for facilities is provided by the relevant local authorities. Improper waste disposal is subject to penalties applicable in the respective area.