User Guide for TZS models including: TP-BF02, TPBF02, 2AKI8-TP-BF02, 2AKI8TPBF02, Bluetooth Headset, TP-BF02 Bluetooth Headset

19BF18 说明书 测试

User Manual

TOPWAY EM ENTERPRISE LTD. TP-BF02 Bluetooth Headset 2AKI8-TP-BF02 2AKI8TPBF02 tp bf02

Not Your Device? Search For Manuals / Datasheets:

File Info : application/pdf, 17 Pages, 1.86MB

PDF GetApplicationAttachment.html?id=6067970


In the Box


Boom Mic 3.5mm Audio Cable

Type-C Charging Cable User Guide



Answer/End call/ Mute/Unmute
Rotate boom mic
Boom mic mute switch

On/Off/Pairing Bluetooth LED Audio Input
Internal mic Boom microphone

Previous track
Play/Pause Next track Rotate to adjust volume Type C charging port 03

How to Wear
1. Insert the detachable Boom Microphone into the 2.5mm receptacle located on the headset.
Mic receptacle Note: Please fully insert the boom microphone before use.

2. The boom microphone can move to accommodate a user's preference for right side or left side wear.
3. Position the microphone to your preference.

Operation Power On

Slide the switch to the CENTER position

Power Off

Slide the switch to the position


Connecting How to connect with the Bluetooth device.


Devices TZS TP-BF02

ON Paired

Now discoverable

Slide the power switch to the " " position and hold until `pairing' heard or the pairing LED ashes.

Activate "Bluetooth" in your device`s settings and select "TZS TP-BF02".

indicate the headphone is connected, and `connected' is heard.

Calls with a Smartphone Calls with a Smartphone

Press 1 × Press 1 × Press 2 ×

Answer End Call Decline


Press 2 × 08

Charging the Headset
During charging the red LED will light. When fully charged, the LED will turn
Plug the USB-C charging cable into a computer's USB port.
Plug the USB-C charging cable into a USB wall charger.

Other Operations
Muting the Boom Mic: Depress and hold the button for 2 seconds.
Muting the internal Mic: (When boom mic is not in use) Depress and hold the call key 2 seconds.

Battery Status: After the headset is powered on, press the call button briefly to hear the current battery status 100% -75%-50%-25%.
Clearing the pairing: While the headset is powered on, press and hold the previous and next track buttons simultaneously for 10 seconds. A pink LED will light for 2 seconds and the headset will then enter pairing mode.

Product Specifications
Bluetooth version: Bluetooth V5.0 Bluetooth Profile: A2DPv1.3.1; AVRCPv1.6;HFPv1.7; HSPv1.2; SPP v1.2; DID v1.3; HID v1.1; PXP v1.0.1; FMP v1.0; BAS v1.0 Working Frequency: 2.402GHz-2.480GHz Frequency Response: 99±3dB Receiving sensitivity: >-89dBm Battery type: Lithium polymer Mic type and sensitivity: Virtual Microphone -42±3dB Headphone Driver Size: 30mm Battery capacity: 410mAh DC Input: 5V_500MA FCC ID: 2AKI8-TP-BF02 Charging voltage: 5V/2A Bluetooth working range: Up to 10m Talk time: Up to 26 hours Charging time: Approximately 2 hours Standby time: Approximately 205 hours Compatibility: Windows 10, mac OS 10.14 or later,iOS and Android

Headsets can deliver sounds at loud volumes and high-pitched tones. Avoid prolonged use of the headset at excessive sound pressure levels. Please read the safety guidelines below prior to using this headset.
Safety information Use of a headset will impair your ability to hear other sounds. Use caution while using your headset when you are engaging in any activity that requires your full attention. This package contains small parts that may be hazardous to children and should be kept out of reach from children.Do not attempt: To dismantle or service the product as this may cause a short circuits or other malfunction which could result in a fire or electric shock.Avoid exposing your product to rain, moisture or other liquids to avoid damage to the product or injury to you. Keep all products, cords, and cables away from operating machinery. Avoid use while operating a motor vehicle. Built-in battery care: Please observe the following if the product contains a battery. Your product is powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times but will eventually wear out.

Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A product with a hot or cold battery may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures well below freezing. Battery warning! CAUTION ­ The battery used in this product may present a risk of fire or chemical burn if mistreated. Do not attempt to open the product or replace the battery. This will void the warranty.

Troubleshooting & Support
Headphones will not power on: · Be sure the headphones are fully charged.
· Remove "TZS TP-BF02" from your phone's Bluetooth device list and try again.
· If the model still does not appear, restart the headset and phone, then try again.
After successfully pairing, the headphones disconnect · Be sure the battery has adequate power and recharge. · Headphones must be within 10m of most mobile devices. · Connections may be affected by obstructions such as walls or
other electronic devices. Try moving closer to the device you are connected to. When answering a call, I cannot hear anything · Ensure the mobile device is connected to the TZS TP-BF02 headphones and not on phone's speaker or other audio option. · Increase the volume on your mobile device.

There is no sound when listening to music · Increase the volume on your headphones or the mobile device. · Reestablish the Bluetooth wireless connection between the
headphones and your mobile device. · Check if the audio app has paused or stopped playback. Headphones will not charge · Confirm that the charging cable is operational or undamaged. · Ensure that the USB charging cable is fully seated in the
headphones and wall charger ports. · Confirm that the USB port is outputting power. Some USB ports
shut off when the PC is off.

FCC Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help



Adobe PDF library 15.00 Adobe Illustrator CC 23.0 (Windows)