Introduction
VEVOR is committed to providing tools at competitive prices. The term "Save Half", "Half Price" or any other similar expressions used by VEVOR only represents an estimate of savings you might benefit from buying certain tools with VEVOR compared to the major top brands and does not necessarily mean to cover all categories of tools offered by VEVOR. You are kindly reminded to verify carefully when you are placing an order with VEVOR if you are actually saving half in comparison with the top major brands.
This is the original instruction manual. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
Product Specifications
Fuel Tank Capacity: 2.75 Liters (as indicated by "Diameter 2.75L" on page 2)
Assembly Instructions
The following describes the assembly process based on the provided diagrams and parts list. Refer to the part numbers for specific components.
General Assembly Steps:
- Attach the Support Legs (4) to the main frame using Bolts (3) and Flat Pads (6, 7, 8).
- Mount the Engine (9) onto the frame using Motor Shock Pads (5) and Bolts (10, 13).
- Connect the Engine to the Motor Connecting Plate (1) using a Flat Key (2).
- Assemble the Blade Plate Welding Assembly (20) with Blades (Type J Blade - 21, Triangle Blade - 22) and Blade Washers (23), Blade Liners (24), and Blade Loose Lock Sheet (25). Secure with Bolts (26).
- Attach the assembled Blade Plate to the engine shaft.
- Install the Blade Cover Components (37) and Blade Cover (41) using Bolts (42, 38).
- Assemble the Hopper Assembly (33) with Hopper Handlebar (34) and secure it to the main frame using Bolts (38) and Flange Locknuts (35). Attach the Hopper Bucket Seal Pad (36).
- Install the Bough Branch Inlet Assembly (14) and Bold Branch Protective Curtain (12) to the hopper.
- Assemble the Wheel Shaft Components (43) and attach the Wheel Assemblies (52) with Flat Pads (53) and Bolts (54). Install Wheel Lock Sheets (46, 51) and Brake Correlators (47, 50) if applicable.
- Install the Protective Curtain Press Board (31) and Rubber Protection Curtain (32) to the discharge chute area.
- Attach the Out Cap (39) and Screw (40).
- Install the Collect Bag (58) to the discharge chute.
- Ensure all bolts and nuts are tightened securely, using the specified washers and lock nuts.
Note: Specific diagrams show detailed placement of parts like the Runcork pin (44) to fix components.
Parts List
| No. | Description | Qty |
|---|---|---|
| 1 | Motor Connecting Plate | 1 |
| 2 | Flat Key 6.3x6.3x52 | 1 |
| 3 | Bolt M8× 65 | 4 |
| 4 | Support Leg | 1 |
| 5 | Motor Shock Pad | 4 |
| 6 | Flat Pad 8.5x32x3 | 8 |
| 7 | Flat Pad 8 | 8 |
| 8 | Big Flat Pad 8 | 3 |
| 9 | Engine | 1 |
| 10 | Bolt M6× 16 | 12 |
| 11 | Bold Dendric Flange | 1 |
| 12 | Bold Branch Protective Curtain | 1 |
| 13 | Type 1 Non metal Insert Hexagon Locking Nut M6 | 12 |
| 14 | Bough Branch Inlet Assembly | 1 |
| 15 | Flange Locknut M8 | 25 |
| 16 | Blades Bottom Panel Components | 1 |
| 17 | Spring Washer 8 | 7 |
| 18 | Gasoline Machine Shaft Head Gasket | 1 |
| 19 | Bolt M8× 35 | 4 |
| 20 | Blade Plate Welding Assembly | 1 |
| 21 | Type J Blade | 2 |
| 22 | Triangle Blade | 2 |
| 23 | Blade Washer | 4 |
| 24 | Blade Liner | 4 |
| 25 | Blade Loose Lock Sheet | 1 |
| 26 | Bolt M10× 50 | 4 |
| 27 | Blade Plate Cover Assembly | 1 |
| 28 | Flange Bolt M8 x 20 | 14 |
| 29 | Flange With Toothed Nuts M8 | 1 |
| 30 | Flat Pad 6 | 6 |
| 31 | Protective Curtain Press Board | 1 |
| 32 | Rubber Protection Curtain | 1 |
| 33 | Hopper Assembly | 1 |
| 34 | Hopper Handlebar | 1 |
| 35 | Flange Locknut M6 | 12 |
| 36 | Hopper Bucket Seal Pad | 1 |
| 37 | Blade Cover Components | 1 |
| 38 | Bolt M6 × 20 | 12 |
| 39 | Out Cap | 1 |
| 40 | Screw M8 x 100 | 1 |
| 41 | Blade Cover | 1 |
| 42 | Bolt M8 × 16 | 3 |
| 43 | Wheel Shaft Components | 1 |
| 44 | Runcork Pin 2.5 × 35 | 2 |
| 45 | Bolt M6× 25 | 2 |
| 46 | Wheel Lock Sheet (Left) | 1 |
| 47 | Left Brake Correlator | 1 |
| 48 | Flange Bolt M8 x 16 | 3 |
| 49 | Down to earth Round Steel | 1 |
| 50 | Right Brake Correlator | 1 |
| 51 | Wheel Lock Sheet (right) | 1 |
| 52 | Wheel Assembly 4.10/3.50-6 | 2 |
| 53 | Flat Pad 16 | 2 |
| 54 | British hexagonal bolt 3/8 24UNF×2 | 1 |
| 55 | Bolt M8 × 14 | 4 |
| 56 | Blade Loose Lock Sheet | 2 |
| 57 | Cutting Blade | 2 |
| 58 | Collect Bag | 1 |
| 59 | Brake Skin | 2 |
| 60 | Flat Pad 4 | 4 |
| 61 | Rivet ×4 x 16 | 4 |
Operation Instructions
Refer to the diagrams showing the "CHOKE" lever for starting procedures.
Starting the Engine:
- Ensure the engine is properly assembled and fueled.
- Set the CHOKE lever to the "START" position.
- Pull the starter cord to crank the engine.
- Once the engine starts, gradually move the CHOKE lever to the "RUN" position as it warms up.
Operation:
Feed branches and organic material into the hopper. The chipper shredder will process them. Ensure safety precautions are followed during operation.
Stopping the Engine:
Refer to the engine's specific stop procedure (typically involves a throttle or kill switch).
FCC Information
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This product may cause harmful interference. 2) This product must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the product.
Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the product and receiver.
- Connect the product to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
Correct Disposal
This product is subject to the provision of European Directive 2012/19/EU. The symbol showing a wheelie bin crossed through [symbol of a wheelie bin crossed through] indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.
Support
For technical support and e-warranty information, please visit: www.vevor.com/support
