DUNE HD(HK) LIMITED 4KSOLO DUNE HD Pro Vision 4K Solo 2AJH3-4KSOLO 2AJH34KSOLO 4ksolo
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO Maximum Permissible Exposure Report 1. Product Information FCC ID: Product name Additional Model No. Model Declaration Test Model Power supply Operation frequency Antenna Type Antenna Gain Hardware version Software version Channel Number Channel Spacing Exposure category EUT Type Device Type 2AJH3-4KSOLO DUNE HD Pro Vision 4K Solo Max Vision 4K, Ultra Vision 4K, Real Vision 4K, Real Vision 4K Duo SmartBox 4K Plus PCB board, structure and internal of these model(s) are the same, So no additional models were tested Pro Vision 4K Solo For AC Adapter: Input: 100-240V~, 50/60Hz, 1.2A MAX Output: 12V 3000mA 2402MHz ~ 2480MHz 2412MHz ~ 2462 MHz 5180MHz-5240MHz 5745-5825MHz Eeternal Antenna BT: 2.0dBi(Max), WIFI: 5.0dBi(Max.) DUNE_V4 210214_0331_r17 79 channels for Bluetooth V5.0 (BDR/EDR) 40 channels for Bluetooth V5.0 (BT LE) 11 Channels for 20MHz bandwidth (2412~2462MHz) 7 Channels for 40MHz bandwidth (2422~2452MHz) 4 channels for 20MHz bandwidth (5180-5240MHz) 2 channels for 40MHz bandwidth (5190~5230MHz) 5 channels for 20MHz bandwidth(5745-5825MHz) 2 channels for 40MHz bandwidth(5755~5795MHz) 5MHz General population/uncontrolled environment Production Unit Mobile Devices 2. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission's guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO 3. Limit 3. 1 Refer Evaluation Method ANSI C95.11999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: Mobile Devices 3. 2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range(MHz) Strength(V/m) Strength(A/m) (mW/cm²) (minute) Limits for Occupational/Controlled Exposure 0.3 3.0 614 1.63 (100) * 6 3.0 30 1842/f 4.89/f (900/f2)* 6 30 300 61.4 0.163 1.0 6 300 1500 / / f/300 6 1500 100,000 / / 5 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range(MHz) Strength(V/m) Strength(A/m) (mW/cm²) (minute) Limits for Occupational/Controlled Exposure 0.3 3.0 614 1.63 (100) * 30 3.0 30 824/f 2.19/f (180/f2)* 30 30 300 27.5 0.073 0.2 30 300 1500 / / f/1500 30 1500 100,000 / / 1.0 30 F=frequency in MHz *=Plane-wave equivalent power density 4. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4R² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. Antenna Information DUNE HD Pro Vision 4K Solo can only use antennas certificated as follows provided by manufacturer; Antenna type and antenna number Eeternal Antenna Operate frequency band Maximum antenna gain 2402MHz-2480MHz 2.0dBi Notes BT Antenna Eeternal Antenna 2412MHz-2462MHz 5180MHz-5240MHz 5745MHz-5825MHz 5.0dBi 2.4WiFi&5GWIFI Antenna This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. 6. Conducted Power Mode GFSK /4DQPSK 8DPSK [BT Max Conducted Power] Channel Frequency (MHz) 0 2402 39 2441 78 2480 0 2402 39 2441 78 2480 0 2402 19 2440 39 2480 FCC ID: 2AJH3-4KSOLO Peak Conducted Output Power (dBm) 1.855 2.310 2.064 2.499 2.936 2.647 2.475 2.927 2.629 Mode BT LE [BLE Max Conducted Power] Channel Frequency (MHz) 0 2402 19 2440 39 2480 Peak Conducted Output Power (dBm) 1.546 2.031 1.786 Mode 11B 11G 11N20SISO 11N40SISO [2.4GWIFI Max Conducted Power Ant0] Channel Frequency (MHz) Max Conducted Power(dBm) 1 2412 16.28 6 2437 16.96 11 2462 16.5 1 2412 16.84 6 2437 17.77 11 2462 16.05 1 2412 16.62 6 2437 17.4 11 2462 16.74 3 2422 16.79 6 2437 17.23 9 2452 16.78 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO Mode 11B 11G 11N20SISO 11N40SISO [2.4GWIFI Max Conducted Power Ant1] Channel Frequency (MHz) Max Conducted Power(dBm) 1 2412 16.75 6 2437 17.41 11 2462 17.41 1 2412 16.84 6 2437 17.62 11 2462 16.76 1 2412 16.14 6 2437 17.65 11 2462 16.07 3 2422 16.14 6 2437 16.63 9 2452 17.46 Mode [5.2GWIFI Max Conducted Power Ant0] Channel Frequency (MHz) Max Conducted Power(dBm) 36 5180 15.56 11A 40 5200 15.21 48 5240 14.9 36 5180 15.63 11N20 SISO 40 5200 15.84 48 5240 15.75 38 11N40 SISO 46 5190 5230 15.72 15.43 36 5180 16.24 11AC20 SISO 40 5200 16.11 48 5240 15.77 38 11AC40 SISO 46 5190 5230 15.81 15.53 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO Mode [5.2GWIFI Max Conducted Power Ant1] Channel Frequency (MHz) Max Conducted Power(dBm) 36 5180 15.00 11A 40 5200 14.65 48 5240 14.25 36 5180 15.06 11N20 SISO 40 5200 14.78 48 5240 14.32 38 11N40 SISO 46 5190 5230 14.58 14.23 36 5180 14.99 11AC20 SISO 40 5200 14.71 48 5240 14.32 38 11AC40 SISO 46 5190 5230 15.3 14.97 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO Mode 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO [5.8WIFI Max Conducted Power Ant0] Channel Frequency (MHz) Max Conducted Power(dBm) 149 5745 13.6 157 5785 14.04 165 5825 14.59 149 5745 13.75 157 5785 14.33 165 5825 14.87 151 5755 13.56 159 5795 14.29 149 5745 14.99 157 5785 14.71 165 5825 14.32 151 5755 15.3 159 5795 14.97 Mode 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO [5.8WIFI Max Conducted Power Ant1] Channel Frequency (MHz) Max Conducted Power(dBm) 149 5745 14.38 157 5785 15.18 165 5825 15.83 149 5745 16.3 157 5785 16.52 165 5825 16.88 151 5755 16.24 159 5795 16.79 149 5745 16.24 157 5785 16.11 165 5825 15.77 151 5755 15.81 159 5795 15.53 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 6 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. 7. Measurement Results Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) BT GFSK (Peak) Channel 0 Channel 39 1.0 2.0 1.0 1.0 /4DQPSK (Peak) Channel 0 Channel 39 2.0 2.0 1.0 1.0 8DPSK (Peak) Channel 0 Channel 19 2.0 2.0 1.0 1.0 Channel Target (dBm) Tolerance ±(dB) BLE BT LE (Peak) Channel 0 Channel 19 1.0 2.0 1.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 2.4GWIFI_Ant 0 11B (Peak) Channel 1 Channel 6 16.0 16.0 1.0 1.0 11G (Peak) Channel 1 Channel 6 16.0 17.0 1.0 1.0 11N20SISO (Peak) Channel 1 Channel 6 16.0 17.0 1.0 1.0 11N40SISO (Peak) Channel 3 Channel 6 16.0 17.0 1.0 1.0 FCC ID: 2AJH3-4KSOLO Channel 78 2.0 1.0 Channel 78 2.0 1.0 Channel 39 2.0 1.0 Channel 39 1.0 1.0 Channel 11 16.0 1.0 Channel 11 16.0 1.0 Channel 11 16.0 1.0 Channel 9 16.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 7 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 2.4GWIFI_Ant1 11B (Peak) Channel 1 Channel 6 16.0 17.0 1.0 1.0 11G (Peak) Channel 1 Channel 6 16.0 17.0 1.0 1.0 11N20SISO (Peak) Channel 1 Channel 6 16.0 17.0 1.0 1.0 11N40SISO (Peak) Channel 3 Channel 6 16.0 16.0 1.0 1.0 FCC ID: 2AJH3-4KSOLO Channel 11 17.0 1.0 Channel 11 16.0 1.0 Channel 11 16.0 1.0 Channel 9 17.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 2.4GWIFI_MIMO 11N20MIMO (Peak) Channel 1 Channel 6 19.0 20.0 1.0 1.0 11N40MIMO (Peak) Channel 3 Channel 6 19.0 19.0 1.0 1.0 Channel 11 19.0 1.0 Channel 9 20.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) 5.2GWIFI_Ant0 11A (Peak) Channel 36 Channel 40 15.0 15.0 1.0 1.0 11N20 SISO (Peak) Channel 36 Channel 40 15.0 15.0 1.0 1.0 11N40 SISO (Peak) Channel 38 15.0 1.0 11AC20 SISO (Peak) Channel 36 Channel 40 16.0 16.0 Channel 48 14.0 1.0 Channel 48 15.0 1.0 Channel 46 15.0 1.0 Channel 48 15.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 8 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 1.0 1.0 11AC40 SISO (Peak) Channe38 15.0 1.0 FCC ID: 2AJH3-4KSOLO 1.0 Channel 46 15.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 5.2GWIFI_Ant1 11A (Peak) Channel 36 Channel 40 15.0 14.0 1.0 1.0 11N20 SISO (Peak) Channel 36 Channel 40 15.0 14.0 1.0 1.0 11N40 SISO (Peak) Channel 38 14.0 1.0 11AC20 SISO (Peak) Channel 36 Channel 40 14.0 14.0 1.0 1.0 11AC40 SISO (Peak) Channe38 15.0 1.0 Channel 48 14.0 1.0 Channel 48 14.0 1.0 Channel 46 14.0 1.0 Channel 48 14.0 1.0 Channel 46 14.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 9 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. 5.2GWIFI_MIMO Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 11N20 MIMO (Peak) Channel 36 Channel 40 18.0 18.0 1.0 1.0 11N40 MIMO (Peak) Channel 38 18.0 1.0 11AC20 MIMO (Peak) Channel 36 Channel 40 18.0 18.0 1.0 1.0 11AC40 MIMO (Peak) Channe38 18.0 1.0 FCC ID: 2AJH3-4KSOLO Channel 48 18.0 1.0 Channel 46 17.0 1.0 Channel 48 18.0 1.0 Channel 46 18.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 5.8GWIFI_Ant0 11A (Peak) Channel 149 Channel 157 13.0 14.0 1.0 1.0 11N20 SISO (Peak) Channel 149 Channel 157 13.0 14.0 1.0 1.0 11N40 SISO (Peak) Channel 151 13.0 1.0 11AC20 SISO (Peak) Channel 149 Channel 157 14.0 14.0 1.0 1.0 11AC40 SISO (Peak) Channe151 15.0 1.0 Channel 165 14.0 1.0 Channel 165 14.0 1.0 Channel 159 14.0 1.0 Channel 165 14.0 1.0 Channel 159 14.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 10 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 5.8GWIFI_Ant1 11A (Peak) Channel 149 Channel 157 14.0 15.0 1.0 1.0 11N20 SISO (Peak) Channel 149 Channel 157 16.0 16.0 1.0 1.0 11N40 SISO (Peak) Channel 151 16.0 1.0 11AC20 SISO (Peak) Channel 149 Channel 157 16.0 16.0 1.0 1.0 11AC40 SISO (Peak) Channe151 15.0 1.0 FCC ID: 2AJH3-4KSOLO Channel 165 15.0 1.0 Channel 165 16.0 1.0 Channel 159 16.0 1.0 Channel 165 15.0 1.0 Channel 159 15.0 1.0 Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) Channel Target (dBm) Tolerance ±(dB) 5.8GWIFI_MIMO 11N20 MIMO (Peak) Channel 149 Channel 157 18.0 18.0 1.0 1.0 11N40 MIMO (Peak) Channel 151 18.0 1.0 11AC20 MIMO (Peak) Channel 149 Channel 157 18.0 18.0 1.0 1.0 11AC40 MIMO (Peak) Channe151 18.0 1.0 Channel 165 19.0 1.0 Channel 159 18.0 1.0 Channel 165 18.0 1.0 Channel 159 18.0 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 11 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO 8. Evaluation Results 8.1 Standalone MPE Evaluation As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna refer to antenna information, the RF power density can be obtained. BT Band/Mode GFSK /4DQPSK 8DPSK f (GHz) 2.441 2.441 2.441 RF output power dBm mW 3.0 1.9953 3.0 1.9953 3.0 1.9953 Antenna Gain (dBi) 2.0 2.0 2.0 Antenna Gain (linear) 1.5849 1.5849 1.5849 MPE (mW/cm2) 0.0006 0.0006 0.0006 MPE Limits (mW/cm2) 1.0000 1.0000 1.0000 BLE Band/Mode BT LE f (GHz) 2.440 RF output power dBm 3.0 mW 1.9953 Antenna Gain (dBi) 2.0 Antenna Gain (linear) 1.5849 MPE (mW/cm2) 0.0006 MPE Limits (mW/cm2) 1.0000 2.4GWIFI_Ant 0 Band/Mode f (GHz) IEEE 802.11b IEEE 802.11g IEEE 802.11n HT20 IEEE 802.11n HT40 2.437 2.437 2.437 2.452 2.4GWIFI_Ant 1 Band/Mode f (GHz) IEEE 802.11b IEEE 802.11g IEEE 802.11n HT20 IEEE 802.11n HT40 2.437 2.437 2.437 2.452 RF output power dBm mW 17.0 50.1187 18.0 63.0957 18.0 63.0957 18.0 63.0957 RF output power dBm mW 18.0 63.0957 18.0 63.0957 18.0 63.0957 18.0 63.0957 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0315 0.0397 MPE Limits (mW/cm2) 1.0000 1.0000 5.0 3.1623 0.0397 1.0000 5.0 3.1623 0.0397 1.0000 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0397 0.0397 MPE Limits (mW/cm2) 1.0000 1.0000 5.0 3.1623 0.0397 1.0000 5.0 3.1623 0.0397 1.0000 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 12 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO 2.4G WIFI_MIMO Band/Mode f (GHz) IEEE 802.11nmimo HT20 IEEE 802.11nmimo HT40 2.437 2.452 RF output power dBm mW 21.0 125.8925 21.0 125.8925 Antenna Gain (dBi) Antenna Gain (linear) 8.01 6.3241 MPE (mW/cm2) 0.1584 MPE Limits (mW/cm2) 1.0000 8.01 6.3241 0.1584 1.0000 5.2GWIFI_Ant 0 Band/Mode f (GHz) 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.180 5.200 5.190 5.180 5.190 RF output power dBm 16.0 mW 39.8107 16.0 39.8107 16.0 39.8107 17.0 50.1187 16.0 39.8107 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 5.0 3.1623 5.0 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0250 0.0250 0.0250 0.0315 0.0250 MPE Limits (mW/cm2) 1.0000 1.0000 1.0000 1.0000 1.0000 5.2GWIFI_Ant 1 Band/Mode f (GHz) 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.180 5.200 5.190 5.180 5.190 RF output power dBm 16.0 mW 39.8107 16.0 39.8107 15.0 31.6228 15.0 31.6228 16.0 39.8107 5.2GWIFI_MIMO Band/Mode f (GHz) 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.200 5.190 5.180 5.190 RF output power dBm mW 19.0 79.4328 19.0 79.4328 19.0 79.4328 19.0 79.4328 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 5.0 3.1623 5.0 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0250 0.0250 0.0199 0.0199 0.0250 MPE Limits (mW/cm2) 1.0000 1.0000 1.0000 1.0000 1.0000 Antenna Gain (dBi) Antenna Gain (linear) 5.0 6.3241 5.0 6.3241 5.0 6.3241 5.0 6.3241 MPE (mW/cm2) 0.0999 0.0999 0.0999 0.0999 MPE Limits (mW/cm2) 1.0000 1.0000 1.0000 1.0000 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 13 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AJH3-4KSOLO 5.8GWIFI_Ant0 Band/Mode f (GHz) 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.825 5.825 5.795 5.745 5.795 5.8GWIFI_Ant1 Band/Mode f (GHz) 11A 11N20 SISO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.825 5.825 5.795 5.745 5.795 RF output power dBm 15.0 mW 31.6228 15.0 31.6228 15.0 31.6228 15.0 31.6228 16.0 39.8107 RF output power dBm 16.0 mW 39.8107 17.0 50.1187 17.0 50.1187 17.0 50.1187 16.0 39.8107 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0199 0.0199 MPE Limits (mW/cm2) 1.0000 1.0000 5.0 3.1623 0.0199 1.0000 5.0 3.1623 0.0199 1.0000 5.0 3.1623 0.0250 1.0000 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 3.1623 5.0 3.1623 MPE (mW/cm2) 0.0250 0.0315 MPE Limits (mW/cm2) 1.0000 1.0000 5.0 3.1623 0.0315 1.0000 5.0 3.1623 0.0315 1.0000 5.0 3.1623 0.0250 1.0000 5.8GWIFI_MIMO Band/Mode f (GHz) 11N20 MIMO 11N40 SISO 11AC20 SISO 11AC40 SISO 5.825 5.795 5.745 5.795 RF output power dBm mW 20.0 100.0000 19.0 79.4328 19.0 79.4328 19.0 79.4328 Antenna Gain (dBi) 5.0 Antenna Gain (linear) 6.3241 MPE (mW/cm2) 0.1258 MPE Limits (mW/cm2) 1.0000 5.0 6.3241 0.0999 1.0000 5.0 6.3241 0.0999 1.0000 5.0 6.3241 0.0999 1.0000 Remark: 1. Output power including turn-up tolerance; 2. Output power is burst average power; 3. MPE evaluate distance is 20cm from user manual provide by manufacturer; 4. MPE values = PG/4R² 8.2 Simultaneous Transmission MPE The sample support two 2.4G&5GWIFI Antenna and another one BT transmit antenna, so need consider simultaneous transmission; Simultaneous transmission MPE According to KDB447498 for Transmitters used in mobile exposure conditions for simultaneous transmission operations; of MPE ratios 1.0 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 14 of 15 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. Mode BT+2.4GWIFI_MIMO BT+5GWIFI_MIMO MPE max ratios 0.1590 0.1264 Limit 1.0 1.0 FCC ID: 2AJH3-4KSOLO Results Pass Pass 9. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. ----------------THE END OF REPORT--------------- This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 15 of 15