TP-Link Deco BE3600

About This Guide

This guide provides a brief introduction to the BE3600 Whole Home Mesh Wi-Fi 7 System and regulatory information. Features available in Deco may vary by model and software version. Deco availability may also vary by region or ISP. All images, steps, and descriptions in this guide are only examples and may not reflect your actual Deco experience.

Conventions

In this guide, the following conventions are used:

More Info

• Specific product information can be found on the product page at https://www.tp-link.com.
• A Technical Community is provided for you to discuss our products at https://community.tp-link.com.
• Our Technical Support contact information can be found at the Help center of the Deco app and the Contact Technical Support page at https://www.tp-link.com/support.

Disclaimers

Speed/Coverage/Device Quantity Disclaimer: Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11 specifications. Actual wireless data throughput and wireless coverage, and quantity of connected devices are not guaranteed and will vary as a result of network conditions, client limitations, and environmental factors, including building materials, obstacles, volume and density of traffic, and client location.

MU-MIMO Disclaimer: Use of MU-MIMO requires clients to also support MU-MIMO.

IoT Compatibility Disclaimer: IoT compatibility refers only to smart devices that can be controlled via the Deco app. Other wireless devices can still connect to Deco for normal Wi-Fi use.

Seamless Roaming Disclaimer: Clients need to support 802.11k/v/r and may require additional set up. Performance may vary depending on the client device.

Appearance

Each Deco has an LED that changes color according to its status, a WPS button, two Gigabit WAN/LAN ports, a power slot, and a Reset button. See the explanation below:

Tip: The product label can be found at the bottom of the product.

• Pulse Yellow: Deco is resetting.
• Solid Yellow: Deco is starting up.
• Pulse Blue: Deco is ready for setup.
• Solid Blue: Deco is setting up.
• Pulse Green: Deco is upgrading firmware.
• Solid Green: Deco is all set up and connected.
• Pulse Red: The satellite Deco is disconnected from the main Deco.
• Solid Red: Deco has an issue.

Diagram Description: A white, circular Deco unit is shown from the front and rear. The rear view highlights the ports and buttons.

• WPS Button: Press this WPS button, and immediately press the WPS button on your client device to start the WPS process.
• Reset Button: Press for 1 second and release to reset Deco to factory default settings. The light changing from pulsing yellow to solid yellow indicated a successful reset.
• 2x Gigabit WAN/LAN Ports: For connecting Deco to your modem, the Ethernet outlet, or for other internet services.
• Power Slot: For connecting Deco to the power socket via the provided power adapter.

Set Up Your Deco

First, let's start by setting up the Deco network. Get the TP-Link Deco app for iOS or Android, then follow the app to walk through the setup.

1. Get the Deco app

Scan the QR code below or go to Google Play or the App Store to download the Deco app. Install the app on your Android or iOS smartphone or tablet.

[QR code for app download]

[Google Play badge]

[App Store badge]

2. Log in or sign up with TP-Link ID

Open the app and log in with your TP-Link ID. If you don't have a TP-Link ID, create one first.

Note: If you forgot your login password, tap Forgot Password?. The app will help you reset your password.

App Screen Description: A login screen titled "Welcome to Deco" with fields for "TP-Link ID (Email)" and "Password", and buttons for "Log In", "Forgot Password?", and "Don't have an account?".

3. Create a Network

In the Deco app, tap the + button on the top right corner of the homepage, then select Create a Network.

App Screen Description: The Deco app's homepage shows a "Change Network" option and an "Add Device" section. Below "Add Device", there are options like "Add a Deco Unit", "Replace Main Deco", "Add EasyMesh Nodes". At the bottom, there is a "Create a Network" button with the text "Set up a new network with this Deco.". A '+' icon is visible in the top right corner.

4. Plug in your Deco

Plug in your Deco and wait until your Deco's LED pulses blue, then your phone/tablet will connect to the Deco automatically.

Note: You can turn on Bluetooth on your phone/tablet in advance for a quicker setup.

App Screen Description 1: A screen showing a Deco unit plugged in, with text "Plug in your Deco and wait until the LED pulses blue." A link "Why is my LED not pulsing blue?" is present.

App Screen Description 2: A screen titled "Turn on Bluetooth to find your Deco". It instructs the user to turn on Bluetooth in Control Center to continue setup, stating Bluetooth is only used to transfer data. A graphic shows a phone with Bluetooth enabled connecting to a Deco unit.

App Screen Description 3: A prompt "'Deco' Wants to Join Wi-Fi Network 'Deco_XXXX' ?" with "Cancel" and "Join" buttons.

App Screen Description 4: A screen titled "Looking for Deco...". It explains that the Deco app will ask to join the "Deco_XXXX" network, and the user should tap "Join".

App Screen Description 5: A screen titled "Deco BE22 is found". It shows a diagram of a Deco unit and states "Tip: The LED of this Deco is solid blue." A "Set Up the Deco" button is present.

5. Connect your Deco

Power off your modem. Connect your Deco to the modem and power it on. If you don't have a modem, connect your Deco directly to the Ethernet outlet.

App Screen Description 1: "Connect Deco to your modem via an Ethernet cable". A button "I don't have a modem" is shown.

App Screen Description 2: "Restart your modem". Instructions to ensure proper setup by turning the modem off and on again. A "Modem Restarted" button is present.

App Screen Description 3: "Connect Deco to a LAN port". Instructions to connect Deco to a network-providing device's LAN port, such as a router, switch, or internet outlet.

6. Specify your Deco's location

Select or custom a location for your Deco. The location will be used as the name of your Deco.

App Screen Description: A list of locations is shown: "Living Room", "Bedroom", "Main Bedroom", "Office", "Kitchen", "Hallway", "Study Room", "Basement", "Garage", "Family Room", and "Custom".

7. Connect your Deco to the internet

Select the internet connection type and enter the information. If you are not sure, contact your internet service provider.

App Screen Description: A screen titled "Connect your Deco to the internet". It prompts to "Enter the information provided by your ISP (internet service provider). If you are unsure, contact your ISP." Options for "Internet Connection Type" (e.g., Dynamic IP) and "Advanced Settings" are shown, with a "Next" button.

8. Create your Wi-Fi network

Set a network name and a password. These will be the name and password you use to connect your devices to Wi-Fi.

App Screen Description: A screen titled "Create your Wi-Fi Network". It states "This will be the name and password you'll use to access your network. Your password must be at least 8 characters." A "Poor" strength indicator is shown for the password. It recommends using a combination of letters, numbers, and symbols. A "Next" button is present.

9. Keep your Deco up-to-date

Set auto update time. This allows your Deco to automatically update to the latest firmware which provides better network experience.

App Screen Description: A screen titled "Keep your Deco up-to-date." It explains that auto update allows the Deco to automatically update to the latest firmware for better performance. An "Update Schedule" is shown with time slots (e.g., 03:00 - 05:00). A "Skip" button and a "Next" arrow button are present. A note explains that updates are rescheduled if the Deco detects internet usage.

10. Setup complete

Your Deco network is now up. You can connect your devices to the Deco network for better connections.

App Screen Description: A "Your Deco network is now up" screen with celebratory graphics. It states "This Deco is ready to use. Please connect all devices to the Deco network for better connections." Buttons for "Add Another Deco" and "Done" are present.

11. Plug in other Decos (if any)

Place the other included Decos in a suitable position and plug them on, and they will join the network automatically.

App Screen Description 1: "Place the other Deco units". It advises placing other Deco units in other rooms, with a distance not exceeding two rooms or walls. A "See Placement Guide" button is present, followed by a "Next" button.

App Screen Description 2: "Plug in all Deco units". It instructs to plug in all Deco units, and they will automatically join the network. The message "Then you're all set. Enjoy!" is displayed. A "Done" button is present.

Troubleshooting

Solutions to common problems during setup or use are provided here for reference. Follow the steps and the provided link below to diagnose and solve problems you might experience with your Deco. If problems still exist, contact us: https://www.tp-link.com/support

Q1. What should I do if I fail to configure the main Deco and get stuck on "We couldn't find Deco"?

Refer to the guide https://www.tp-link.com/support/faq/2239/ or follow the video https://youtu.be/2HYuEYS9XJM

Q2. What should I do if I fail to configure the satellite Deco and get stuck on "We couldn't find another Deco"?

Refer to the guide https://www.tp-link.com/support/faq/1447/ or follow the video https://youtu.be/iVgDzoo16T4

Q3. What should I do if I fail to configure the main Deco and get stuck on "Testing Internet Connection"?

Refer to the guide https://www.tp-link.com/support/faq/2239/

Refer to the video https://youtu.be/OSUrGdWH-i0

Q4. What should I do if my wireless devices cannot connect to Deco?

Refer to the guide https://www.tp-link.com/support/faq/2718/

Q5. What should I do if Deco suddenly lost internet access?

Refer to the guide https://www.tp-link.com/support/faq/2428/

Q6. How can I find a suitable spot for my Deco?

Refer to the guide https://www.tp-link.com//support/faq/1446/

Q7. What can I do if the Deco app isn't working properly?

Refer to the guide https://www.tp-link.com/support/faq/1456/

Authentication and Compliance Information

FCC Compliance Information Statement

[FCC logo]

Product Name: BE3600 Whole Home Mesh Wi-Fi 7 System

Model Number: Deco BE22

Responsible party:

TP-Link Systems Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

TP-Link Systems Inc. has determined that the equipment shown has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2025-02-18

FCC Compliance Information Statement (I.T.E Power Supply)

[FCC logo]

Product Name: I.T.E POWER SUPPLY

Model Number: T120150-2B4

Responsible party: TP-Link Systems Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

TP-Link Systems Inc. has determined that the equipment shown has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2025-02-18

CE Mark Warning

[CE mark]

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

• 2400MHz–2483.5MHz (20dBm)
• 5150MHz–5250MHz (23dBm)
• 5250MHz–5350MHz (23dBm)
• 5470MHz–5725MHz (30dBm)

Frequency band 5150 - 5250 MHz:

Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.

Frequency band: 5250 - 5350 MHz:

Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.

Frequency band: 5470 - 5725 MHz:

Installations and use in road vehicles, trains and aircraft and use for unmanned aircrafts systems (UAS) are not permitted. Outdoor use, including in road vehicles, is not permitted.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body.

National restrictions (EU)

Attention: This device may only be used indoors in all EU member states and EFTA countries, and Northern Ireland.

AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU IE IS IT LI LT LU LV MT NL NO PL PT RO SE SI SK UK(NI)

UKCA Mark

[UKCA mark]

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/

National restrictions (UK)

Attention: This device may only be used indoors in Great Britain.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Caution:

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; DFS (Dynamic Frequency Selection) products that operate in the bands 5250-5350 MHz, 5470-5600MHz, and 5650-5725MHz.

Avertissement:

Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; Les produits utilisant la technique d'atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250-5350 MHz, 5470-5600MHz et 5650-5725MHz.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement:

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice:

注意!

取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。

前述合法通信,指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

應避免影響附近雷達系統之操作。

安全諮詢及注意事項

• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
• 清潔本產品之前請先切斷電源。請勿使用液體、噴霧清潔劑或濕布進行清潔。
• 注意防潮,請勿將水或其他液體潑灑到本產品上。
• 插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。
• 請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。
• 不要私自拆開機殼或自行維修,如產品有故障請與原廠或代理商聯繫。

限用物質含有情況標示聲明書

設備名稱 (Equipment name): BE3600 Whole Home Mesh Wi-Fi 7 System

型號(型式) (Type designation (Type)): Deco BE22

Note 1: "Exceeding 0.1 wt %" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.

Note 2: "○" indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3: The "—" indicates that the restricted substance corresponds to the exemption.

Safety Information

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

[EAC logo]

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact TP-Link.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.
• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact TP-Link.
• Operating Temperature: 0°C–40°C (32°F–104°F)
• 運作溫度: 0℃–40°C (32°F–104°F)
• This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.

Please read and follow the above safety information when operating the device. TP-Link cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Symbols may vary from products.

產品標籤上符號的解釋 (Explanation of symbols on the product label)

符號可能因產品而異

注意:產品標籤可以在產品底部和其I.T.E.電源供應器上找到。