Bauer Keyless Compartment Door Latches

Product Overview

The Bauer Keyless Compartment Door Latches offer four styles for direct replacement of current Slam Latches. Each latch is a self-contained, smart latch that communicates with a smartphone or through the Bauer Gateway. Latches are powered by a 9V battery, with standard alkaline batteries lasting approximately 3 months and lithium batteries lasting 6 months. Battery life can be extended by turning off the 9V Battery Holder when in storage.

Latches can be locked/unlocked manually with a key or via the Bauer Connect App, available on Google Play Store or Apple Store. Multiple latches, including Bauer's NE or EM Keyless Entrance Door Latches, can be grouped for one-touch locking/unlocking via the Bauer Connect App. Bauer Products Locking and security products utilize Bluetooth Low Energy (BLE) for communication. A limit exists on the total number of BLE devices that can connect to a phone simultaneously, including other devices like earbuds and vehicles. Factors influencing connections and performance include the BLE specification limit (typically 7) and the phone's manufacturer and model. Bauer recommends a maximum of 4-6 connections for Android phones with an S22 or A35 processor, and 6-8 for iOS phones. For more connections, Bauer BLE Gateway or Bauer Cellular/Wi-Fi Gateway is recommended.

Installation Considerations

• Bauer Keyless Compartment Door Latches function best on storage compartments. Doors with access panels or obstructions like refrigerators may diminish Bluetooth signal strength.
• Door manufacturers have slightly different cut-outs. Ensure the latch fits properly and engages the door. The paddle should be tight with the housing when the door is closed, and in the normally closed position when the door is open, indicating the spring-loaded plunger is fully engaged.

Installation Instructions

BP-20E and BP-22E Keyless Compartment Door Latch Installation

Most compartment doors are hinged on top, rotating upwards, which can make self-installation challenging. Assistance is recommended.

1. Remove the old lock.
2. Clean the cut-out, removing any dirt or loose material.
3. Install the Outside Assembly of the lock on the exterior of the compartment door, guiding the wire through the cut-out.
4. Plug the Battery Wire from the Inside Plate Assembly into the Receptacle on the wire.
5. Carefully align the lugs and mounting holes on the Inside Assembly and install screws. Tighten in a cross pattern, avoiding crushing or cutting wires.

Note for BP-22E: Align the Plunger Cam with the Paddle Cam to ensure the paddle retracts the plunger when opened.

BP-24E and BP-25E Keyless Compartment Door Latch Installation

Similar to the BP-20E/BP-22E, installation may be challenging due to door orientation, and assistance is recommended.

1. Remove the old lock.
2. Clean the cut-out.
3. Install the Outside Assembly of the lock on the exterior of the compartment door.
4. Align the Inside Assembly with the Outside Assembly. Ensure the Square Shaft Paddle Clutch (Outside Assembly) aligns with the Lock Cylinder Cam (Inside Assembly), and the Paddle Cam (Outside Assembly) aligns with the Plunger Cam (Inside Assembly).
5. Install screws, tightening in a cross pattern.

Changing Batteries

BP-20E and BP-22E

1. Remove the Wire Cover Screws to access the 9V Battery Holder.
2. Remove the Wire Cover. The 9V Battery Holder is attached by Velcro.
3. Carefully pull the 9V Battery Holder off the Inside Plate without pulling the wire or dropping it.
4. Slide the back cover off, remove the old battery, and install a new one (Energizer brand recommended).
5. Replace the back cover, place it on the Inside Plate, and reinstall the Wire Cover with the attaching screws.

BP-24E and BP-25E

1. Remove the two (2) Wire Cover Screws for access to the 9V Battery Holder. Do not remove the Mechanism Cover with three (3) screws.
2. Remove the Wire Cover, being careful to prevent the 9V Battery Holder from falling out.
3. Carefully pull the 9V Battery Holder off the Inside Plate.
4. Slide the back cover off the 9V Battery Holder, remove the old battery, and install a new one (Energizer brand recommended).
5. Replace the back cover on the 9V Battery Holder, place it on the Inside Plate, and reinstall the Wire Cover with the two (2) attaching screws.

Keyless Compartment Door Latch Pairing with Smart Phone

1. Download the Bauer Connect App from the Google Play or Apple Store.
2. Turn ON the 9V Battery Pack.
3. Stay near the Keyless Latch you wish to pair.
4. Open the Bauer Connect App and touch the Pair or "+" buttons.
5. Select "Compartment Door Latch" from the list of devices to pair.
6. The App will recognize the type of Keyless Lock. Touch the screen of the lock you wish to pair. Select the lock with the strongest signal (RSSI). Note: RSSI of -30 is stronger than RSSI of -60.
7. Use the key to cycle the lock cylinder to pair. Ensure your key is nearby and remain within a few feet of your latch. Manually unlock your device with the key to complete the process.
8. When prompted to Pair, touch "Pair".
9. Once successfully paired, the lock status will appear on the display.

Troubleshooting and FAQ

• App doesn't discover any locks:
  • Check that the 9V Battery Holder is turned ON.
  • Ensure you are close to the keyless latch.
  • Close and re-open the app.
  • Verify your phone meets the minimum requirements (e.g., S22 or newer for Android, iPhone 7 or newer for Apple).
• App Display states “CHECK LOCK”: Take the key and cycle the lock until the display indicates Locked or Unlocked.
• BP-22E, BP-24E, and BP-25E Paddle opens but Plunger does not move: Remove the Inside Plate Assembly and re-align the Paddle Cam and Plunger Cam to ensure they are correctly engaged.
• Weak signal from Lock: Verify that the door does not have an obstruction such as a panel or refrigerator that could interfere with the signal.