ABSOLUTE Digimatic Indicator ID-C

Features

• The new Peak Hold-Type Digimatic Indicator features both a Key-Lock and Parameter-Lock to prevent accidental changing of settings during operation.
• Parameter setting software makes it even easy to set all available parameters.
• An analog bar provides easy-to-read values when scanning for Max, Min and TIR Values.
• The maximum, minimum or runout value can be displayed during measurement.
• Go/no-go judgment is performed by setting the upper and lower tolerances for max., min. and runout values.
• High speed sampling ratio of 50 times/s.
• Employing the ABSOLUTE linear encoder, the Signal ID-C always displays the spindle Absolute Position from the origin when turned on.

Technical Data

Accuracy:

Refer to the list of specifications

Resolution:

0.001-0.01mm or .00005-.0005"/0.001-0.01mm

Display:

LCD

Length standard:

ABSOLUTE electrostatic capacitance-type linear encoder

Max. response speed:

Unlimited

Measuring force:

1.5N or less

Battery:

CR2032 (1 pc.), 05SAA217

Battery life:

Approx. 12 months under normal use

IP Rating:

Equivalent to IP-42*¹

*¹ A protection class indication (IP=International Protection) is based on the IEC 60529/DIN40050 part 1/JIS D0207, C0920. The level indicated is valid only if the output connector cap is installed.

Function

Key Lock, Parameter Lock, PC-USB Input, Analog Bar, Fast measurement frequency, Preset (up to 3 values), Tolerance Judgment, Peak Detection, Calculation (Ax), inch/mm conversion (on inch/metric models only) Counting direction switching, Data Output

Alarm: Low voltage, Counting value composition error, Overflow error, Tolerance limit setting error

Specifications

The product is available in ISO/JIS type and ANSI/AGD type configurations.

Inch/Metric (Stem dia. 3/8" #4-48 UNF Thread)

Inch/Metric (Stem Ø 8mm, M2.5 x 0.45 Thread)

Metric (Stem Ø 8mm, M2.5 x 0.45 Thread)

Dimensions

Detailed description of the indicator's physical dimensions and features, including front and side views. The unit is in millimeters (mm), with ANSI/AGD type dimensions in parentheses. The display can rotate 330°.

Side View: Overall height approximately 85.4 mm. The main body width is 28.6 mm. The stem diameter at the bottom is M2.5 x 0.45 (#4-48 UNF), with a length of 7.6 mm.

Front View: The top stem diameter is Ø10.9 mm. The overall height from the top of the stem to the bottom of the contact point is approximately 82.2 mm (calculated as 10.9mm + 50.1mm + 21.2mm). The main body height is 50.1 mm. The distance from the top of the body to the center of the spindle is 46.5 mm (44.2 mm for ANSI/AGD). The contact point has a diameter of Ø8 mm with a tolerance of 0 to -0.009 mm (3/8" for ANSI/AGD). The contact point length is 7.3 mm (6.35 mm for ANSI/AGD). The display is centrally located on the circular face.

Optional Accessories

• 905338: Connecting Cable (1m)
• 905409: Connecting Cable (2m)
• 21EZA313: Parameter Setting USB Cable
• 21EZA198: Spindle lifting lever (12.7mm ISO/JIS type)
• 21EZA199: Spindle lifting lever (12.7mm ASME/AGD type)
• 21EZA105: Lifting Knob (12.7mm/.5" ISO/JIS models)
• 21EZA150: Lifting Knob (12.7mm/.5" ASME/AGD models)
• 21EZA197: Lifting Knob (for 25.4/1″mm models)
• 21EZA200: Lifting Knob (for 50.8/2"mm models)
• 540774: Spindle lifting cable
• Backs (Refer to page F-33.)
• Contact points (Refer to page F-34.)