Triple Monitor Counterbalance Desk Mount
Instruction Manual
Key Specifications
- VESA Compatibility: 75x75, 100x100
- Max Screen Size: 27"
- Weight Capacity: (2-9kg) x 3 monitors / (4.4-19.8lbs) x 3 monitors
If you have any questions, please feel free to contact our customer service via Amazon.
Model: AHP-63-US1.0
WARNING!
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
All are included in B
- A (x1) Arm
- A1 (x2) Harness Cover
- B (x1) Clamp
- B1 Bracket
- B2 Clip Plate
- B3 Bolt Y
- B4 Bolts (x2)
- C (x1) Decorative Cover
- D (x3) VESA Plate
- E (x1) Middle Head
- E1 (x2) Plastic Spacer
- F (x1) Base
- F1 (x3) Pad
- G (x1) Wire Clip
- H (x3) Bolt
- I (x1) 5mm Allen Key
- J (x1) 6mm Allen Key
- M-A (x12) M4x12mm Screws
- M-B (x12) M4x30mm Screws
- M-C (x12) D5 Washer
- M-D (x24) Spacer H5mm
DO NOT EXCEED WEIGHT CAPACITY. (4.4~19.8lbs)x3 / (2~9kg)x3
NOTE: Not all hardware included will be used.
ASSEMBLY STEPS
STEP 1: Apply Pads To The Base Bottom
Paste the Pad (F1) onto the Base (F).
STEP 2: Clamp Installation Or Grommet Base Installation
OPTION A: Clamp Installation
Loosen Bolts (B4) using 5mm Allen Key (I). Align the screw hole on the Base (F), and lock the Screw (B4) with a 5mm Allen Key (I).
Fix the Decorative Cover (C) to the Base (F) and fix the bracket on the table by tightening the Clamp (B).
Desk thickness requirement: [10mm-50mm]
Caution: [Do not overtighten]
OPTION B: Grommet Base Installation
Detach Clip Plate (B2) and Bolt Y (B3) from Clamp (B).
Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (F) and the table board together.
Desk thickness requirement: [10mm-50mm]
STEP 3: Arm Installation
Install the Middle Head (E), Wire Clip (G), swivel Arm (A) on the base in sequence as shown. Fasten the bolt with supplied 6mm Allen Key (J).
STEP 4: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to the back of the monitor and secure with Screws (M-A) with Washers (M-C) using 5mm Allen Key (I). Avoid excessive tightening to prevent monitor damage.
OPTION B: Curved Back Monitor
Attach the VESA Plate (D) to the back of the monitor and secure with Screws (M-B) with Washers (M-C) and Spacer (M-D) using 5mm Allen Key (I). Avoid excessive tightening to prevent monitor damage.
NOTE: Hand tighten screws to avoid over tightening.
STEP 5: Hang Monitor
Slide the monitor onto the head of the swivel arm. Install the Security Bolt (H). Ensure the security bolt is tightened before rotating the monitor.
Important Notice: Once the monitor is hanged on, hold it with both hands and DO NOT let go suddenly. Leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Adjust Tilting Angle
Problem: If monitor face down
Solution: 1. Loosen the tilting bolt. 2. Hold the bottom of the monitor with one hand and adjust to determine your desired tilt angle. 3. Retighten the tilting bolt to fix the intended angle.
STEP 6: Adjust Tension
For intended functioning, adjust the tension of Arm (A) according to your monitor weight using the 6mm Allen Key (J).
Note 1: Be sure to keep the arm in a horizontal position during adjustment, otherwise it may be difficult to adjust or damage the mount.
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution: Turn the inside screw counterclockwise ("+" direction) to increase gas spring tension until the arm stays as intended.
Situation 2: Arm rises up
Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise ("-" direction) to decrease gas spring tension until the arm stays as intended.
Note 2: Adjustment Guide
| Monitor Weight | 2kg | 3kg | 4kg | 5kg | 6kg | 7kg | 8kg | 9kg |
|---|---|---|---|---|---|---|---|---|
| Circles(AT LEAST) | min | 2 | 4 | 6 | 8 | 10 | 12 | 15 |
STEP 7: Cable Management
Remove bottom plastic covers from the gas spring Arm (A). Run cables from the monitor through the bottom of the gas spring Arm (A). Then attach the Wire Cap (A1) onto the upper arm of the Arm (A). Reattach plastic covers as shown in the diagram.
[Push and Slide] [Remove the harness cap]
[Insert and Push]
Adjust as Desired
Note: The total length of 3 monitors after arrayed cannot be longer than 183cm.
Adjust monitor position and rotation.
- Tilt
- Swivel
- Rotation
Tilt: ±90°
Swivel: ±180°, ±135°, ±90°
Rotation: ±180°
Note: To ensure stability, the tightness of the rotating axis has been preset, making it difficult to rotate the VESA plate.
Suggestion: Attach the monitor first, then hold the two sides of it with both hands and rotate vigorously. If that doesn't work, please ask for help.
Safety warning: Please do not move stand outside desk for safety!
Product Dimensions
VESA hole patterns: 75x75mm, 100x100mm (2.95", 3.94", 4.5")
Clamp thickness: [10mm-50mm]
Arm reach: min1256mm~max1376mm
Vertical adjustment range: min215~max275mm
Max monitor height: max290mm
Other dimensions: 47mm, 35mm, 183mm, 407mm, 25mm, 60mm.
Tilt: +90°/-90°
Swivel: ±180°, ±135°
CAUTION AND MAINTENANCE:
- Never allow children to climb, stand, hang, or play on any part of the monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
