This document is a reference for configuring “Vibe Communications” SIP trunks with Panasonic. KX-NS1000 systems and includes the settings required for ...
Setup Reference guide for KX-NS1000 Version 4.2 Firmware "Vibe Communications" SIP Trunk service (with Built-in Router) Version 1.0(PSCEU) 28.April, 2015 SUMMARY This document is a reference for configuring "Vibe Communications" SIP trunks with Panasonic KX-NS1000 systems and includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation. SIP trunk details such as account ID, authentication ID, password and DDI number will be provided by Vibe Communications. Attention: This document was created based on the results of test environment accounts. Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of completing this Inter-Operability Test Panasonic will provide technical support for any issues experienced an assist as far as possible in providing a resolution. Please obtain relevant information from Service provider before configuration of SIP trunks. Panasonic will not be held liable for any information provided in this guidance document. Information used in this document is for interoperability testing. Information and Specifications in this document are subject to change without notice. Note [SIP Registration] As per Vibe Communications procedures, the example configurations use a Global IP Address for authentication. [Transfer Function] Vibe Communications does not support REFER transfer method use CO to CO Transfer. [FAX] Both codec are supported; a G.711 Inband codec and a T.38 codec. Table of Contents (1) SIP Trunk and Extension Port number configuration: (2) Provisioning a SIP trunk: (3) Incoming Call Routing: (4) Outgoing Call CLI: (5) CLIR Outgoing Call (Withholding number): (6) Built-in Router and WAN settings: (7) Packet Filtering Settings : Page 3 Page 6 Page 8 Page 9 Page 10 Page 11 Page 13 2 (1) SIP Trunk and Extension Port Number Configuration Note: SIP Trunk Port number in this document is described it as port 5060(Trunk) and 15060(Extn). Click [1. Slot] Move mouse over [Site Property] and click [Main]. Click [Port Number] tab and change [UDP Port No. for SIP Extension Server] (Default:5060) to other number. (i.e.15060). and click [OK]. 3 Go to [1.Configuration 1.Slot] Click [Virtual] and move mouse over [V-SIPGW16], and click [Ous]. Click [OK] pop-up window. Move mouse over [V-SIPGW16] again, and click [Shelf Property]. Select [Main] tab and change the two items. [SIP Client Port Number] (Default:35060) to 5060 [NAT Traversal] Off (Not used when enable the WAN/Built-in Router) [NAT Fixed Global IP] 0.0.0.0 (Same as above) and click [OK]. Move mouse over [V-SIPGW16] again, and click [Ins]. *Note: Need to Save the System data and Restart the PBX after making these port changes. *Note: Save the System data and Restart the PBX after making these port changes. 4 IMPORTANT! To secure the PBX from illegal attacks, please restrict the above port forwarding ports to only be accessible from the Vibe Communications source IP addresses. Gamma Assured Service When Assured Services are provided, the Vibe Communications provided router will be responsible for all NAT functions. Consequently, NAT Traversal can be disabled in the SIP GW Shelf Property above (set to Off) 5 (2) Provisioning the SIP Trunk SIP Trunk Port Property Move mouse over [V-SIPGW16] and click [Ous] and Select [Port Property] SIP Trunk Port Property continued [Main] Tab 1. Channel Attribute: Basic Channel 2. Provider Name: Enter a name reference only 3. SIP Server Location Name: Not required 4. SIP Server Location IP Address: 85.133.58.137 (Vibe Communications provided) 5. SIP Server port Number: Leave at 5060 6. SIP Service Domain: Not required 7. Subscriber Number: Not required 6 SIP Trunk Port Property continued [Account] Tab 1. User name: Enter the SIP Account (User name) as supplied by Vibe Communications. (Note this is user name without @85.133.58.137) For example: SIP Account (User name) = 02012345678 Enter: 02012345678 2. Authentication ID: Enter the Authentication ID as supplied by Vibe Communications. (Note this is authentication ID without @85.133.58.137) For example: Authentication ID = 02012345678 Enter: 02012345678 3. Authentication Password: Not required. SIP Trunk Port Property continued [Register] Tab 1. Register Ability: 2. Register Interval: 3. Un-Register Ability: 4. Registrar Server Name: 5. Registrar Server IP Address: 6. Registrar Server port number: Disable Leave at 3600 Leave enabled Not required Not required Leave at 5060 7 (3) Incoming Call Routing Go to [CO & Incoming call] and select [3.DDI /DID Table] 1. DDI/DID Number: 2. DDI/DID Name: 3. DDI/DID Destination: Enter the DDI number in the appropriate format (see below) Example: 020-1234-5678 Enter: 02012345678 Determined by the installer (optional setting) Determined by the installer (extension number, group etc) 8 (4) Outgoing Call CLI Note: There is no information for Call CLI during testing. It is described as generally settings. Move mouse over [V-SIPGW16] click [Ous] Select [Port Property] and [Calling Party] Tab From Header User Part: PBX-CLIP Click [OK]. Go to [4.Extension, 1.Wired Extension, 1.Extension Settings] & select [CLIP] [CLIP] tab Enter a valid CLI number for each required extension in the CLIP ID field Click [OK]. 9 (5) CLIR Outgoing Call (Withholding Number) Go to [4.Extension, 1.Wired Extension, 1.Extension Settings] & select [CLIP] [CLIP] tab 1. CLIR: Enable Go to [Port Property] and select [Calling Party] Tab [Calling Party] Tab 2. Header Type: P-Preferred-Identity Header 10 (6) Built-in Router and WAN Settings NS1000 has a Built-in Router and filtering functions (Ver3.2 or later) so advanced routing configuration can be managed by the NS1000 and the internet router/modem simply providing internet access. Go to [Router Configuration]->[1.Setup]->[2.WAN]->[1.Connection Settings] Select the appropriate the Connection Type. In this example, we use the Static IP address option. WAN IP Address: Subnet Mask: Gateway: Preferred DNS IP Address: Alternative DNS IP Address: Enter your actual IP address. Enter the appropriate subnet mask. Enter the actual Gateway IP address. Enter the actual DNS IP address. Enter the actual Alternative DNS IP address. Click [Apply]. 11 LAN Setting. Go to [Network Service]->[1.IP Address/Ports] Default Gateway: Blank * Delete the "LAN Default Gateway IP address" if it's entered IP address. Note: NS1000 will work as the router, Not need the LAN Gateway. DNS IP Address: Blank * Delete the "Preferred DNS" and "Alternative DNS" if it's entered IP address. To use DNS address entered [Router Configuration], this field must be blank. . Click [Apply] Perform System Reset for changes to take effect. 12 (7) Packet Filtering Settings Go to [Router Configuration] --> [2.Firewall] --> [2.Packet Filtering] Click [Advanced Setting] LAN->WAN Basic Policy: WAN -> LAN Basic Policy: Entry No.: Filter: [Accept] [Discard] Select [1] Select [Enable] 13 Configure Filter 1, this is the setting pass through packet from Vibe server, port 5060. Protocol Number: [Protocol Name] and choose [UDP] TCP/UDP Source Port: /Port Number [Port Number] / [5060] -[ 5060] TCP/UDP Destination Port /Number: [Port Number] / [5060] -[ 5060] Source: [Address] IP Address: [85.133.58.137] Enter your assigned Server IP Direction: [WAN->LAN] Click [Apply] 14 Set Filter 2, this is the setting block packet from except Vibe server port 5060. Click [Advanced Setting] LAN->WAN Basic Policy: WAN -> LAN Basic Policy: Entry No.: Filter: [Accept] [Discard] Select [2] Select [Enable] 15 Protocol Number: TCP/UDP Source Port: TCP/UDP Destination Port /Number: Source: Direction : Policy : [Protocol Name] and choose [UDP] [Any] [Port Number] / [5060] -[ 5060] [Any] [WAN->LAN] [Discard] Click [OK] Go to following page. 16 Confirm the Packet Filtering Settings 17Microsoft Word 2016 Microsoft Word 2016