Aegislink Smart Lock Q106

Safety

Please read this section carefully to ensure your safety and to prevent potential damage.

• Do not install or repair this lock without proper authorization. Improper installation may incur additional costs. Professional installation is highly recommended.
• Do not use water, alcohol, or any other corrosive materials to clean this lock. Clean it with a dry, soft cloth.
• Do not operate this lock if your hands are wet, and keep liquids away from this lock to avoid malfunctioning or damage.
• Make sure that no unauthorized person has access to your passwords or mechanical keys. For your home security, it is recommended to change the password periodically.
• Make sure that the door is completely closed when going outside.
• Remember to set a new administrator password and fingerprint after resetting the lock. Otherwise, any fingerprint will be able to unlock the door.
• Keep mechanical keys in a safe, secure location. They function as a backup and prevent you from getting locked out of your house if your passwords, fingerprints, and app are all inoperative.
• Check the Reset button regularly to ensure it has not been tampered with.
• Replace batteries immediately when you receive a low battery warning. The lock will notify you via a voice message. If the battery power runs out, charge the lock with a power bank through the emergency power port on the bottom of the lock.
• Restrict access to your phone and passwords to prevent your home from being broken into.
• Do not use excessive force or sharp objects to push the lock buttons as this can damage the lock.
• Be sure to match the poles (+/-) when installing the batteries. Improper installation of the batteries can cause them to burst or corrode.

Packaging

The package includes the following items:

• 1 x Front panel
• 1 x Back panel
• 1 x Iron plate
• 1 x Deadbolt
• 1 x Buckle plate
• 4 x Tapping screws (M4 × 0.8 in)
• 2 x Back panel screws (M4 x 0.4 in)
• 1 x Back panel screw (M4 x 1 in)
• 1 x Connection column & screw (M4 x 1.5 in)
• 4 x Front panel screws (M5 x 1.8 in/2.2 in)
• 1 x Buckle box
• 3 x Mechanical keys

Diagram Description: The packaging contents are illustrated with labeled components corresponding to the list above.

Product Overview

The Aegislink Smart Lock Q106 comprises several components:

• 1: Front panel
• 2: Connection column (standby)
• 3: Front panel block
• 4: Deadbolt
• 5: Pick jack
• 6: Wire
• 7: Iron plate
• 8: Standby connection column screw (M4 × 1.5 in)
• 9: Back panel
• 10: Back panel screws (M4 x 0.4 in)
• 11: Battery cover
• 12: Reset button
• 13: Back cover
• 14: Back panel screw (M4 x 1 in)
• 15: Knob
• 16: Switch button
• 17: Front panel screws (M5 x 1.8 in/2.2 in)
• 18: Tapping screws (M4 x 0.8 in)
• 19: Pick
• 20: Emergency power port
• 21: Key cover

Diagram Description: An exploded view shows the assembly of the smart lock, with each part numbered and identifiable. The front panel features a touchscreen keypad and a rotary knob. The back panel houses the battery compartment and internal mechanisms.

Installation

Finding a Suitable Location for Lock Installation

1. Ensure you have a Phillips screwdriver and 4 AA batteries before installation.
2. Ensure the door path is clear and install the lock on the correct side of the door.
3. Measure the size of the door and drill the required holes accordingly. The distance between the door edge and center of the hole should be 2.4 in-2.8 in. The diameter of the hole you drill should be either 1.5 in or 2.1 in. If it is 1.5 in, remove the front panel block for a proper fit.

Note: If you are inexperienced in lock installation, professional installation is highly recommended.

Installing the Deadbolt

1. Place the deadbolt in the "UP" direction, indicated by the arrow, in the door.
2. Install the deadbolt with the tapping screws (M4 x 0.8 in).

Note: The length of the deadbolt can be adjusted from 2.4 in to 2.8 in to fit your door.

Installing the Front Panel and Iron Plate

1. Pass the wire through the hole under the deadbolt, matching the pick with the pick jack. Avoid passing the wire through the hole over the deadbolt to prevent interference with the deadbolt and lock performance.
2. Pass the wire through the iron plate and align the iron plate with the front panel. Ensure holes in both plates are aligned.
3. Secure both plates with the front panel screws (M5 x 1.8 in/2.2 in).

Note: Use M5 x 1.8 in screws for doors 1.4 in-1.8 in thick, and M5 x 2.2 in screws for doors 1.8 in-2.2 in thick. If the lock is loose, drill a 0.8-in diameter hole 3 inches above the door hole and reinforce with the standby connection column screw (M4 x 1.5 in), removing the front panel and iron plate first.

Diagram Description: Illustrates the correct wire routing below the deadbolt and the alignment of the front panel and iron plate, secured by screws. Shows the "UP" arrow for deadbolt installation.

Installing the Back Panel

1. Remove the battery cover and back cover. Pass the wire through the back panel.
2. Align the back panel with the iron plate and secure using M4 x 0.4 in screws in the battery box.
3. Twist the knob vertically to align the pick with the back panel. A click indicates proper alignment.
4. Insert the wire into the port inside the back cover and close the back cover.
5. Reinforce the back panel with the back panel screw (M4 × 1 in).

Diagram Description: Shows the back panel being attached, with the wire connected to the internal port and secured with screws.

Installing the Batteries and Back Cover

1. Install the batteries and battery cover. An audio alert confirms proper installation.
2. Install the buckle plate and box.

Diagram Description: Shows the battery compartment and the back cover being installed.

Lock Calibration

1. To reset the lock, open the battery cover and press the Reset button for 3 seconds.
2. When the button is bright, twist the knob from the vertical position to the horizontal position.
3. Press the 7 button for 3 seconds to automatically correct the door position when closed. The door will automatically lock when closed after calibration.

Diagram Description: Illustrates the knob rotation from vertical to horizontal position for calibration.

Basic Functions

Adding an Administrator

1. Press any button on the lock to wake up the screen.
2. Press the 3 button for 3 seconds or the Reset button.
3. To add the first administrator, enter your desired password twice and then enroll the fingerprint.
   • Password: A valid password is 6 to 8 digits. Enter your password once and confirm with the 3 button; enter it a second time and confirm again.
   • Fingerprint: Set up a fingerprint by pressing a finger to the scanner 6 times. Confirm the scan using the 3 button.
4. To add a second administrator, enter the password or enroll the fingerprint. You can choose password, fingerprint, or both. The lock allows up to 2 administrators.

Notes:

• The lock provides voice instructions for each step.
• The default password is 1234567890. Reset the lock and add new administrator passwords and fingerprints.
• Simple passwords like 123456 are not accepted.

Adding a User

1. Press any button on the lock to wake up the screen.
2. Press the 3 button for 3 seconds or the Reset button, and verify administrator access via an administrator password or fingerprint.
3. To add a user, enter a user password or set up a fingerprint.
   • Password: Each time a user enters a password, confirm it by pressing the 3 button. Passwords can be 6 to 8 digits.
   • Fingerprint: Each time a user sets up a fingerprint, confirm it by pressing the 3 button. The user will need to press their finger to the screen 6 times to set up a fingerprint.

Notes:

• The lock provides voice instructions for each step.
• Up to 50 passwords and 50 fingerprints can be added.

Deleting a User

1. Press any button on the lock to wake up the screen.
2. Press the 3 button for 3 seconds or the Reset button, and verify administrator access via an administrator password or fingerprint.
3. Press the 3 button for 3 seconds again.
4. Press the 1 button to delete all user fingerprints, the 2 button to delete all user passwords, and the 3 button to delete all user information.

Note: Administrators cannot be deleted this way. To delete administrators, reset the lock using the Reset button for 3 seconds. Resetting the lock allows anyone to open it with fingerprints until new ones are enrolled.

Diagram Description: Shows fingerprint icons and confirmation button.

Changing the User Password

1. Press any button on the lock to wake up the screen.
2. Press the 5 button for 3 seconds on the lock screen; you will hear a voice prompt.
3. Enter the old password.
4. Enter a new password twice. Confirm each entry by pressing the 3 button.

Note: The old password becomes invalid after changing. Administrator passwords cannot be changed this way; reset the lock instead.

Resetting the Lock

1. Press the Reset button for 3 seconds; the button will flash blue.
2. To reset, verify administrator access by pressing the 3 button and entering the correct password or fingerprint.
3. After resetting, all information is removed. Add a new administrator as described in the "Adding an Administrator" section.

Note: Calibrate the lock before adding a new administrator. Otherwise, you may not be able to wake up the lock screen.

Adding the Lock to the App

Signing Up in the App

If you have a TuyaSmart account, skip to the next step.

1. Download the TuyaSmart app from the Apple App Store or Google Play Store, or scan the QR code.
2. Sign up in the TuyaSmart app using a valid phone number or email address. Enter the verification code and set a password to complete sign-up.

Diagram Description: Shows app store icons for iPhone and Android, and QR code placeholder.

Connecting the Lock to the App

1. Turn on Bluetooth on your phone.
2. Press the 3 button for 3 seconds, and verify administrator access.
3. Tap the + button on the app page. Add the lock via "Add Manually" or "Auto Scan". "Auto Scan" is recommended for convenience.
4. Auto Scan: The app will automatically find "Bluetooth smart lock". Tap it to start network configuration. A voice message confirms successful addition.

Diagram Description: Shows app screens for connecting via Bluetooth, showing connection progress (e.g., 4%), and device added confirmation.

Add Manually

Follow these instructions: Navigate to Security & Video Surveillance --> Smart Lock.

Note: Ensure your router's Wi-Fi signal is set to 2.4 GHz, as TuyaSmart cannot discover devices on other bands.

Diagram Description: Illustrates the app's device category selection, showing options like "Welcome Home", "Electrical", "Security & Video Surveillance", and "Smart Lock".

Using the App to Control the Door

Operating the Lock via the App

• Tap and Hold to Unlock: Tap and hold to unlock. Pressing the 5 and 8 buttons together puts the lock in regularly open mode.
• Fingerprint & Password Management: Manage fingerprints or passwords within the TuyaSmart app.

Diagram Description: Shows app screens for unlocking, displaying battery level, member management, unlocking records, and settings. Also shows screens for fingerprint and password management.

Member Management

Invite family members to the system and manage the lock via the TuyaSmart app. Administrators can set passwords or fingerprints for themselves and users. Family members can set their own permissions. Only administrators can invite family members to jointly manage the door.

Diagram Description: Illustrates the member management interface, showing options to add family members or other members and their respective permissions.

Low Power Alarm

When the battery is low, a voice message will play upon opening the door. This message will play approximately 50 times. If the battery dies, charge the lock using a power bank via the emergency power port. App functions will not work if the battery is dead.

Volume Adjustment

Press the 3 button three times and the 3 button again to adjust the volume (Mute/Low/High). Each press cycles through Mute, Low, High, or back to Mute.

Regularly Open Mode

Keep the door unlocked. Verify administrator access via password or fingerprint and confirm with the 3 button. Press the 5 and 8 buttons simultaneously to enter regularly open mode. Users or administrators can activate this mode using their credentials.

Note: Ensure your phone is close to the door (within 50 ft) when operating via the app. App interfaces may differ slightly from the manual due to software updates.

Additional Functions

Automatic Locking After Incorrect Passwords or Invalid Fingerprints

The door will lock for 180 seconds if five incorrect passwords or invalid fingerprints are entered consecutively.

Anti-Theft Password

A default password is 6-8 digits. You can enter a 9-16 digit password that includes your real password to prevent theft. Change your password periodically to minimize risk.

Frequent Asked Questions

Q: Is this smart lock compatible with Android and iOS?

A: Yes, this Aegislink smart lock is compatible with both Android and iOS.

Q: Does this smart lock work if my mobile phone is turned off?

A: Yes. You can still lock/unlock the door via password, fingerprint, or key.

Q: What if the door fails to lock automatically when I close the door?

A: Ensure the Auto-Lock function is set. If not, press 7 for 3 seconds and enter the administrator password. The door will automatically lock when closed. If Auto-Lock is confirmed and the door still does not lock, verify installation and battery power. Auto-Lock will not function if the lock is installed improperly or the battery is dead.

Q: Why does the door beep every time I lock or unlock it?

A: Beeping or voice messages may indicate low battery power. Replace the batteries for continuous power supply.

Q: Why can't I open my door via the app when I'm far away?

A: App unlocking can be affected by obstacles. It is recommended to keep your phone as close to the door as possible, or at least within 50 ft.

Specifications

Warranty

Aegislink provides customers with a 60-day refund policy, a 12-month warranty, and lifetime technical support. For after-sales questions, contact service@aegislink.co.uk.

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with Local Authorities or retailers for recycling advice.

Symbol Description: A symbol indicating that the product should not be disposed of with household waste and should be recycled.