iDatalink Maestro TO2 Installation Harness. INSTALL GUIDE ... Wire Color on Alpine cable ... WIRING DIAGRAM without an Amplifier.
OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or "quick printing" this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE Toyota 4 Runner With JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota 4 Runner With JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota 4 Runner With JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 1 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota 4 Runner With JBL 2014-2018 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota 4 Runner With JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota 4 Runner Without JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota 4 Runner Without JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota 4 Runner Without JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 2 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota 4 Runner Without JBL 2014-2018 STEP 5 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota 4 Runner Without JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Avalon With JBL 2015-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Avalon With JBL 2015-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" 3 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS Toyota Avalon With JBL 2015-2018 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Avalon With JBL 2015-2018 STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Avalon With JBL 2015-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Avalon Without JBL 2015-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Avalon Without JBL 2015-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Avalon Without JBL 2015-2018 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Avalon Without JBL 2015-2018 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Avalon Without JBL 2015-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Camry With Factory 6.1" Screen 2012-2014 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Camry With Factory 6.1" Screen 2012-2014 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Camry With Factory 6.1" Screen 2012-2014 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 5 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 CUT REVERSE CAMERA CONNECTOR FROM TO2 T-HARNESS AND CONNECT WIRES AS SHOWN. YELLOW BLACK BLUE/YELLOW BLACK BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED 87654321 16 15 14 13 12 11 10 9 WHITE RED BLACK STEP 3 FACTORY RADIO HARNESS Toyota Camry With Factory 6.1" Screen 2012-2014 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED STEP 5 A F G H MAESTRO RR MODULE H G A F 5 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Camry With Factory 6.1" Screen 2012-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 6 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO STEP 2 CUT REVERSE CAMERA CONNECTOR FROM TO2 T-HARNESS AND CONNECT WIRES AS SHOWN. YELLOW BLACK BLUE/YELLOW BLACK STEP 3 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED 87654321 16 15 14 13 12 11 10 9 WHITE RED BLACK FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED STEP 5 A F G H MAESTRO RR MODULE H G A F 6 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Camry With Factory Screen and HDD and JBL 2012-2014 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WELCOME DURING INSTALLATION Congratulations on the purchase Installation Instructions 3 of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram 4 now a few simple steps away from enjoying your new car radio with enhanced features. Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Camry With Factory Screen and HDD and JBL 2012-2014 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 6 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO STEP 2 CUT REVERSE CAMERA CONNECTOR FROM TO2 T-HARNESS AND CONNECT WIRES AS SHOWN. YELLOW BLACK BLUE/YELLOW BLACK STEP 3 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED 87654321 16 15 14 13 12 11 10 9 WHITE RED BLACK FACTORY RADIO HARNESS WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED STEP 5 A F G H MAESTRO RR MODULE H G A F 6 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Camry With Factory Screen and HDD and JBL 2012-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Camry With JBL 2015-2017 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Camry With JBL 2015-2017 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" 3 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS Toyota Camry With JBL 2015-2017 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Camry With JBL 2015-2017 STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Camry With JBL 2015-2017 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Camry Without JBL 2015-2017 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Camry Without JBL 2015-2017 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Camry Without JBL 2015-2017 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Camry Without JBL 2015-2017 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Camry Without JBL 2015-2017 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Corolla With Factory 6.1" Screen 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Corolla With Factory 6.1" Screen 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Corolla With Factory 6.1" Screen 2014-2018 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Corolla With Factory 6.1" Screen 2014-2018 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Corolla With Factory 6.1" Screen 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Highlander With JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Highlander With JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" 3 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS Toyota Highlander With JBL 2014-2018 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Highlander With JBL 2014-2018 STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Highlander With JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Highlander Without JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Highlander Without JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Highlander Without JBL 2014-2018 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Highlander Without JBL 2014-2018 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Highlander Without JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Rav 4 With Factory 6.1" Screen 2013-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Rav 4 With Factory 6.1" Screen 2013-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Rav 4 With Factory 6.1" Screen 2013-2018 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Rav 4 With Factory 6.1" Screen 2013-2018 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Rav 4 With Factory 6.1" Screen 2013-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" 3 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Sequoia With JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Sequoia With JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Sequoia With JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 1 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Sequoia With JBL 2014-2018 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Sequoia With JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Sequoia Without JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Sequoia Without JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Sequoia Without JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 2 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Sequoia Without JBL 2014-2018 STEP 5 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Sequoia Without JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Sienna With JBL 2015-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Sienna With JBL 2015-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. Note: The reverse camera cannot be retained in this vehicle. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Sienna With JBL 2015-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 7 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN BACKUP CAM STEP 2 CONNECTION NOT REQUIRED REVERSE CAMERA CANNOT BE RETAINED REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Sienna With JBL 2015-2018 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 7 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Sienna With JBL 2015-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Sienna Without JBL 2015-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Sienna Without JBL 2015-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Sienna Without JBL 2015-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 2 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Sienna Without JBL 2015-2018 STEP 5 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Sienna Without JBL 2015-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Tacoma With JBL 2016-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Tacoma With JBL 2016-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" 3 Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS Toyota Tacoma With JBL 2016-2018 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED STEP 3 FACTORY RADIO HARNESS Toyota Tacoma With JBL 2016-2018 STEP 4 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Tacoma With JBL 2016-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Tacoma Without JBL 2016-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Tacoma Without JBL 2016-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 5 · Connect all the harnesses to the Maestro RR module then test your installation. TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 4 ADS-RR(SR)-TOY02-DS Toyota Tacoma Without JBL 2016-2018 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Tacoma Without JBL 2016-2018 STEP 4 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE NOT CONNECTED TO2 T-HARNESS CONNECTION NOT REQUIRED Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS STEP 5 A F G H MAESTRO RR MODULE H G A F 4 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Tacoma Without JBL 2016-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Tundra With JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Tundra With JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Tundra With JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 1 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Tundra With JBL 2014-2018 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Tundra With JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Tundra Without JBL 2014-2018 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Tundra Without JBL 2014-2018 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut and remove the front speaker wire junction connectors. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Tundra Without JBL 2014-2018 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 2 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE YELLOW/GREEN (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Tundra Without JBL 2014-2018 STEP 5 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Tundra Without JBL 2014-2018 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Venza With JBL 2015-2016 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Venza With JBL 2015-2016 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Venza With JBL 2015-2016 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 8 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/GREEN - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE PURPLE/WHITE (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Venza With JBL 2015-2016 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 9 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Venza With JBL 2015-2016 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Venza With JBL and Nav 2013-2014 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Venza With JBL and Nav 2013-2014 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Venza With JBL and Nav 2013-2014 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 8 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM with an Amplifier STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/GREEN - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE PURPLE/WHITE (NOT CONNECTED) LF RCA INPUT RF RCA INPUT CONNECTIONS NOT REQUIRED WITH AMP SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS STEP 2 CUT REVERSE CAMERA CONNECTOR FROM TO2 T-HARNESS AND CONNECT WIRES AS SHOWN. YELLOW BLACK BLUE/YELLOW BLACK STEP 3 AUX IN BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED 87654321 16 15 14 13 12 11 10 9 RED WHITE BLACK FACTORY RADIO HARNESS Toyota Venza With JBL and Nav 2013-2014 STEP 5 RCA CABLES MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO WIRES FROM VEHICLE DATA CABLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 8 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Venza With JBL and Nav 2013-2014 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.com INSTALL GUIDE Toyota Venza Without JBL 2015-2016 Retains factory amplifier, steering wheel controls, and more! PRODUCTS REQUIRED iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro TO2 Installation Harness OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware and that you carefully review the Installation Diagram and Vehicle Wire Reference Chart. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. DURING INSTALLATION Installation Instructions Wiring Diagram Radio Wire Reference Chart Toyota Venza Without JBL 2015-2016 3 4 5 NEED hELP? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. · Remove the factory radio. STEP 2 · If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used). STEP 3 · Connect the factory harness to the TO2 T-harness. STEP 4 · Plug the male WHITE 2 pin connector of your TO2 T-harness into the OBDII harness. · Plug the OBDII connector into the OBDII of the vehicle. STEP 5 · Plug the aftermarket radio harnesses into the aftermarket radio. · Connect the backup camera RCA cable into the aftermarket radio (if equipped). · Connect the auxiliary RCA cables into the aftermarket radio (if equipped). · Plug the Data cable to the data port of the aftermarket radio. STEP 6 · Connect all the harnesses to the Maestro RR module then test your installation. Toyota Venza Without JBL 2015-2016 TROUBLESHOOTING TIPS: · To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds. · For technical assistance call 1-866-427-2999 or e-mail "support@idatalink.com". Visit us at "maestro.idatalink. com/support" and "www.12voltdata.com/forum/" Automotive Data Solutions Inc. © 2018 8 ADS-RR(SR)-TOY02-DS 3 maestro.idatalink.com WIRING DIAGRAM without an Amplifier STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) YELLOW/GREEN - REVERSE LIGHT (+) LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED YELLOW/BLACK - FOOT BRAKE PURPLE/WHITE (NOT CONNECTED) SEE AFTERMARKET RADIO GUIDE FOR RADIO WIRE COLORS AUX IN STEP 2 BACKUP CAM REVERSE CAMERA HARNESS CONNECT IF EQUIPPED Toyota Venza Without JBL 2015-2016 STEP 5 MAIN HARNESS CONNECT TO AFTERMARKET RADIO RCA CABLES CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITH AUXILIARY VIDEO DATA CABLE STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE STEP 4 TO2 T-HARNESS Automotive Data Solutions Inc. © 2018 OBDII CONNECTOR ADS-RR(SR)-TOY02-DS STEP 6 A F G H MAESTRO RR MODULE H G A F 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART Toyota Venza Without JBL 2015-2016 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination Reverse Light E-Brake (+) Orange (+) Purple/White or Yellow/Green (see Wiring diagram) (-) Lt Green Foot Brake (+) Yellow/Black VSS (vehicle speed sensor) (DATA) Pink N/A Orange/White Yellow/Blue Yellow/Black Green/White Orange/White Purple/White Lt Green N/A N/A Orange/White Purple/White Lt Green N/A Pink Automotive Data Solutions Inc. © 2018 ADS-RR(SR)-TOY02-DS 5 maestro.idatalink.comAdobe InDesign CC 2015 (Macintosh) Adobe PDF Library 15.0