User Manual for DAYTON AUDIO models including: LBB-5Sv2, Lithium Battery Charger Board or Module, LBB-5Sv2 Lithium Battery Charger Board or Module, Lithium Battery Charger Board, Lithium Battery Charger Module, Lithium Battery Charger, Battery Charger
It is necessary to start with all new batteries with the same mAh capacity ... Use the following guidelines to determine which LBB-5Sv2 output ports will ...
prieš 2 dienas — It is necessary to start with all new batteries with the same mAh capacity. • Remove the batteries before storing LBB-5Sv2 ... Quick-Start Wiring Diagram.
Dayton Audio LBB-5Sv2 Lithium Battery Charger Dayton Audio LBB-5Sv2 · Batteries sold separately: 18650 x5 1. Use only flat top 18650 batteries, and not 18650 batteries with a button top on the positive side · Package includes 1. LBB-5Sv2 x1 2. 20in stranded power cable x1 3. 8.5in stranded 4-pin plug Power Supply · Between 5 VDC and 24 VDC, center positive · Minimum 2A capable recommended · 2.1 x 5.5mm center positive coax plug Installing Batteries · Plug in all wiring harnesses necessary for project before installing batteries · Match the + side of the battery with the + marker on the LBB-5Sv2 o If a battery's polarity is not marked, check for vent holes or a dimple around the rim of the positive side · You must plug in the power supply to activate the battery board · If a battery goes bad, the board will cease all output Charging Tips · The LBB-5Sv2 uses a BMS (Battery Management System) to monitor the voltage of each cell individually in order to charge them to the same capacity · If one battery is significantly lower in charge than the others, it may take days for all batteries to reach full capacity o Higher level batteries will be slowly drained before all cells are charged together · It is necessary to start with all new batteries with the same mAh capacity · Remove the batteries before storing LBB-5Sv2 for a prolonged amount of time · The DIP switches on S2 control the charge rate by restricting current. If you notice your power supply beginning to get hot, it could be shortening the life of your batteries. Check the setting of your dip switches. The DIP switches must be set to one of the following settings: Switch positions OFF-OFF-OFF-OFF ON-OFF-OFF-OFF ON-ON-OFF-OFF ON-ON-ON-OFF ON-ON-ON-ON Charge current 0.50A 0.60A 0.70A 0.80A 0.90A 2 Dayton Audio LBB-5Sv2 J2 Pin 1 2 Value VIN GND J3 Pin 1 2 3 4 5 6 Value VIN VIN GND GND BATT BATT J5 Pin 1 2 Value VIN GND J7 Pin 1 2 Value LED+ LED- J6 Pin 1 2 Value LED+ LED- J16 Pin 1 2 3 4 5 6 Value POWER SWITCH LED4 LED3 LED2 LED1 (J21) (J27) Pin 1 2 3 4 Value BATT BATT GND GND (J19) Pin 1 2 3 4 5 6 Value BATT BATT BATT GND GND GND J22 Pin 1 2 Value BATT GND Output Current Capabilities How much current your project draws will be the limiting factor when using any battery pack. Do not connect project directly to batteries, use only the voltage output ports of the LBB-5Sv2; otherwise over-current protection will not function. Use the following guidelines to determine which LBB-5Sv2 output ports will work best for your project: · Higher Current Applications Use J19 or J22 when a high amount of current is needed for extended periods of time o Examples of high current uses: larger amplifier boards, LED arrays, large DC motors · Lower Current Applications Use J21 or J27 when less current is needed o Examples of lower current uses: small/medium amplifier boards, smartphone battery bank, PC fans · Maximum Current The LBB-5Sv2 is capable of supplying 5A total from all combined outputs at 21VDC, for a combined output of 105W 3 Dayton Audio LBB-5Sv2 Quick-Start Wiring Diagram 1. (J1) 5 24 VDC power input 2. (J2) 5 24 VDC power input for bare wire 3. (J3) Multifunction expansion port, see page 5 4. (J5) 15 24V Solar panel power input 5. (J19) 24 VDC output port 6. (J22) 21 VDC output port 7. (J21) 21 VDC output port 8. (J27) 21 VDC output port 9. LED charging indicator a. ON = Charging b. OFF = Fully charged 10. (J7) External charge indicator LED, see page 5 11. (J6) External LED indicator for power status, see page 5 12. Power indicator status LED a. ON = Power b. OFF = No power 13. (J16) Multiple external LED Indicator port, see page 5 14. Battery level LED indicators 15. Short press S1 to display battery level readout on LEDs 16. 4-Position DIP switch to control charging current, see table under Charging Tips on page 2 4 Dayton Audio LBB-5Sv2 J3 Feature extension port The feature extension port is a part of what makes the Dayton Audio line of battery modules so versatile. Being mindful of the pinout on page 3, accessories can be plugged into J3 to expand the options the battery board provides. The Dayton Audio LBB-5EB Expansion Board is an easy and effective way to add a 5VDC output to your project. This will allow you to charge smartphones and power other 5VDC devices. There is also a DC input jack to charge the LBB5Sv2 directly through the LBB-5EB. The LED on the LBB-5EB remains on, so if the LED draining the batteries is of concern, it can be removed. J3 power specification: 5VDC, 2A maximum output J6 External power port indicator LED J6 can be used as an external indicator to display the ON/OFF status off the battery board. Following the pinout on page 3, an LED can be connected such that an ON status indicates the board is active and an OFF status indicates the board is inactive. This external LED will serve the same purpose as D10 on the board just below J6. J7 External charge indicator LED J7 is used as an external indicator to display the charging status of the battery board. ON indicates the board is charging, OFF indicates the board is not charging, or has completed charging if the board is plugged in. This serves the same function as D13 on the board just above J7. J16 External battery status indicator LEDs J16 can be used as an external indicator to display the battery level status of the board, serving the same purpose as D16, D17, D18, D19, just below J16. Following the pinout on page 3, 4 LEDs and a momentary switch/button can be connected such that the battery level is displayed by the 4 LEDs. Pressing the momentary switch/button will illuminate the number of LEDs corresponding the status of the battery. 1 LED = 25% 2 LEDs = 50% 3 LEDs = 75% 4 LEDs = 100% Troubleshooting Battery board not supplying power Remove then replace one battery (new battery not necessary) and momentarily plug in your power supply. This will restart the charging circuit and will reactivate the battery supply LBB-5EB expansion not working ensure the LBB-5EB is plugged into the expansion socket (J3) and not the external battery charge status socket. 5 Dayton Audio LBB-5Sv2 Note: The Dayton Audio LBB-5Sv2 is an independent battery holder board and its design does not work with Dayton Audio KAB board's built-in charge circuit. Plug the LBB-5Sv2 into the two wire DC input on the KAB boards or use Dayton Audio battery board KAB-BE with Dayton Audio KAB Bluetooth amp boards. Specifications Output Voltage: 21 VDC @ 5A Max (combined outputs) Supply: 5 to 24 VDC, at least 1.5A recommended DC coax jack size: 2.1 x 5.5mm center positive Dimensions: 4.8" W x 3.6" D x 1.38" H 6Microsoft Word 2016