DENON Wireless Subwoofer Owner's Manual

Owner's Manual for DENON models including: Wireless Subwoofer, DSW-1H

Owner’s

Google Play and the Google Play logo are trademarks of Google LLC. Amazon, Kindle, Echo, Alexa, Dash, Fire and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

Owner’s Manual

Owner’s Manual. Contents Setup Use Troubleshooting Status LED Appendix 1. Introduction 4 Before your begin 5 System requirements 5 Network requirements 5 Hardware Requirements 6 Controller requirements 7 Getting to know your DSW-1H 8 Front panel 9 Controls 10 Back panel 11 Placing your DSW-1H 12

File Info : application/pdf, 48 Pages, 1.08MB

n 20201202115337 DSW-1H Owners Manual

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

.
DSW-1H
WIRELESS SUBWOOFER
Owner's Manual

.
1

Contents

Setup

Introduction Before your begin
System requirements Network requirements Hardware Requirements Controller requirements
Getting to know your DSW-1H Front panel Controls Back panel
Placing your DSW-1H Powering your DSW-1H Getting the HEOS app
Setting up your first DSW-1H Adding more HEOS devices
Adding wired HEOS devices Adding wireless HEOS devices Connecting devices Pairing a DSW-1H to a HEOS device
Pairing DSW-1H to DHT-S716H Pairing DSW-1H to other HEOS device Unpairing the DSW-1H

Use

Troubleshooting

Status LED

4 Making adjustments

Adjusting the Level

Adjusting the Low Pass Filter

Adjusting the Phase

Adjusting the status light brightness

Appendix
20 20 20 21 21

Contents

Setup

Use

Updating your system Advanced features
Wireless performance Power management
Power modes Quick Start Mode Deep Standby Off
Basic troubleshooting My HEOS device won't connect to my network using the audio cable My HEOS device turns off and the status LED flashes in red Connecting to a WPS network Resetting your HEOS device
Status LED table Supported file types and codecs

Troubleshooting

Status LED

Appendix

22 Specifications

23 Information

Trademarks

License

License information for the software used in the unit

25 25 26 26 27 33

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Thank you for purchasing this Denon product. To ensure proper operation, please read this owner's manual carefully before using the product.

NOTE 0 THIS DOCUMENT CONTAINS INFORMATION THAT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Introduction
The DSW-1H is part of the HEOS wireless multi-room sound system that enables you to enjoy your favorite music anywhere and everywhere around your home. By utilizing your existing home network and the HEOS app on your iOS or AndroidTM device, you can explore, browse, and play music from your own music library or from many online streaming music services. 0 True multi-room audio - play different songs in different rooms or the same song in every room 0 Utilizes your existing home wireless network for quick and easy setup 0 Industry leading microsecond audio synchronization between HEOS device 0 Legendary Denon audio quality 0 If you are in a hurry, you can be enjoying great sounding music in no time by following the steps outlined in the Quick Start Guide (supplied).

DSW-1H
Wireless Subwoofer
Quick Start Guide

.
Please continue reading this Owner's Manual for more detailed information about the features and benefits of your DSW-1H.
4

Contents

Setup

Before your begin

Use

Troubleshooting

Status LED

Appendix

NOTE 0 If you have already installed at least one HEOS device, please skip to the section "Adding more HEOS devices" (v p. 16).
System requirements
Before you begin installing your first HEOS device, please make sure you understand and meet a few basic requirements.
o Network requirements
Wireless Router - In order to use your HEOS music system, you must have a working wireless (Wi-Fi) or ethernet network in your home. Even when connected to an Ethernet network, a Wi-Fi connection to the router is required to control the system using the HEOS Control app. If you do not have a wireless network, please contact your local Denon dealer or electronics retailer to assist you with purchasing and installing a wireless network in your home. High Speed Internet Connection - HEOS accesses the Internet to stream music to your home from many popular online music services. HEOS is also designed to provide you with software updates, which are delivered via your home Internet connection. DSL, Cable, and Fiber services will provide the best experience and reliability. You may experience performance issues with slower Internet connections like satellite based services.

Contents

Setup

Use

o Hardware Requirements
Use the DSW-1H together with existing HEOS devices. [Example]

Troubleshooting

Status LED

Appendix

.
NOTE 0 DSW-1H can not be used by itself.

DHT-S716H

HEOS Amp

HEOS speaker

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

o Controller requirements
You can control your HEOS wireless multi-room sound system using the free HEOS app on any iOS or Android mobile device that meets these minimum requirements:

.
iOS Minimum Requirements 0 iOS version 8.0 or later 0 iPhone® 4S or newer 0 iPad® 2 or newer 0 iPod touch® (5th generation) or newer

.
Android Minimum Requirements 0 Android OS version 4.0 or later 0 All resolutions

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Getting to know your DSW-1H

Unpack your DSW-1H from the box and verify that the following items are included:

DSW-1H

Quick Start Guide

Warranty (North America model only)

Safety instructions

Power cord

1/8 inch (3.5 mm) setup cable

Ethernet cable

Feet

.
NOTE 0 Please use the power cord included in the box for your device.
8

Contents
o Front panel

Setup

Use

Troubleshooting

Status LED

Appendix

q
.
A Status LED Please refer to the "Status LED table" for LED color and state meaning. (v p. 27)
9

Contents
o Controls

Setup

Use

Troubleshooting

Status LED

Appendix

qw
.
A Volume up/down buttons (+, ) Adjusts the HEOS device's volume level up or down.
B Mute button (:) Mutes or unmutes the HEOS device's volume.

Contents
o Back panel

Setup

Use

Troubleshooting

Status LED

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

Appendix

rty u
.

A AUX jack (AUX IN) Used to add the HEOS device to your wireless network. (v p. 15)
B USB port Used to connect USB storage devices.
C NETWORK connector Used to connect this unit to a wired Ethernet network. (v p. 15)

E AC inlet (AC IN) Used to connect the power cord. (v p. 13)
F CONNECT button Used for Wi-Fi setup.
G Connect in status LED Indicates the status of this unit. (v p. 27)

D RESET button

Various settings are reset to the factory default values. (v p. 26)

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Placing your DSW-1H
The DSW-1H is designed to add HEOS multi-room audio functionality to an external device which offers audio amplification. You should place your DSW-1H in a convenient location near the speakers you are connecting it to. 0 The DSW-1H must be within range of your wireless network.

0 Attach the included feet to the four corners of the DSW-1H's side if you are placing it on horizontally.

Contents

Setup

Use

Troubleshooting

Powering your DSW-1H
Connect the power cord included in the box to the back of the DSW-1H and the plug to a wall outlet.

Status LED

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

Appendix

for North America (AC 120 V, 60 Hz)
for Europe (AC 220 - 240 V, 50/60 Hz)
.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Getting the HEOS app
The HEOS app is the heart of the HEOS experience. Using your mobile device and the HEOS app, you can setup, browse, explore, and control your HEOS system right in the palm of your hand, from anywhere in your home. Download the HEOS app for iOS or Android by searching App Store®, Google PlayTM store or Amazon for "HEOS".

.
For the purpose of improvement, the specifications and design are subject to change without notice.
NOTE 0 The HEOS app and brand is not affiliated with any manufacturer of any mobile device. Availability of music services may vary by region. Not all services may be available at
time of purchase. Some services may be added or discontinued from time to time based on decisions of the music service providers or others.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Setting up your first DSW-1H
Once you have placed your DSW-1H in your listening room and have downloaded the HEOS app, you are ready to configure your DSW-1H for music playback. This involves following a few simple steps to get the DSW-1H connected to your existing home network:
Caution 0 DO NOT connect the Ethernet cable if you are connecting your DSW-1H to a wireless network. If you are connecting the DSW-1H to a wired network,
use an Ethernet cable to connect the DSW-1H to your network or router.

1 Make sure your mobile device is connected to your wireless network (the same network you want your DSW-1H connected to). You can check this in the Settings - Wi-Fi menu of your iOS or Android device.
NOTE 0 If your wireless network is secure, make sure you know the password to join
your network.
2 Make sure you have the included 1/8 inch (3.5 mm) setup cable handy.
3 Launch the HEOS app on your mobile device.

4 Tap the "Setup Now" button at the top of the screen. 5 Follow the instructions to add the DSW-1H to your
wireless network. The Wi-Fi settings from your mobile device will be copied to the DSW-1H via the audio cable.
NOTE 0 If you have any problems connecting your HEOS device, jump to the
Troubleshooting section. (v p. 25)

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Adding more HEOS devices
The HEOS wireless multi-room sound system is a true multiroom audio system that automatically synchronizes audio playback between multiple HEOS devices so that the audio coming from different rooms is perfectly in sync and always sounds amazing! You can easily add up to 32 devices to your HEOS system.

Adding wired HEOS devices
Just connect the HEOS devices to your home network using an Ethernet cable and the HEOS devices will appear on your HEOS app as a new room in the "Rooms" screen. At your convenience, you can assign a name to the HEOS devices to indicate which room you have it placed in.

0 Use only a shielded STP or ScTP LAN cable which is easily available at electronics stores (CAT-5 or greater recommended). 0 Do not connect a Network Connector directly to the LAN port/Ethernet connector on your computer.

Adding wireless HEOS devices
You can add additional wireless HEOS devices to your HEOS system by selecting "Add Device" from the HEOS app's settings menu and follow the instructions:

Music

Settings

Add Device

.
16

Contents

Setup

Use

Connecting devices

Pairing a DSW-1H to a HEOS device
The DSW-1H needs to be paired with another HEOS device.
o Pairing DSW-1H to DHT-S716H
1 Select the Settings a icon located in the upper left corner of the main "Music" menu to display the Settings menu.
2 Select the DHT-S716H from "My Devices". 3 Select Setup Assistant and add the DSW-1H.
Follow the instructions in the menu to complete the setup.

NOTE
0 A DSW-1H can not playback any audio unless it is paired with some other HEOS device.
0 A DSW-1H needs to connect your wireless network before pairing.

Troubleshooting

Status LED

Appendix

My Devices
Speakers HEOS 3 Left HEOS 3 Right Links HEOS Link Soundbars Denon DHT-S716H Subwoofers Denon DSW-1H
.

Denon DHT-S716H

Name

Denon DHT-S716H

Network

xxxxxxxx

Quality

Normal

Status Light

Setup Assistant

Placement

On Table

TV Input

Contents

Setup

Use

o Pairing DSW-1H to other HEOS device
1 Select the currently unpaired DSW-1H. 2 Select the HEOS device to be paired.
The DSW-1H will be grouped together with it and will play the deep bass of the added HEOS device.

The following HEOS devices can be connected like this 0 HEOS Amp 0 HEOS Link 0 HEOS speaker
NOTE 0 A DSW-1H can not playback any audio unless it is paired with some other HEOS
device. 0 A DSW-1H needs to connect your wireless network before pairing.

Troubleshooting

Status LED

Appendix

Rooms
Drag one room into another to group them HEOS 1 + HEOS 1 Song Name 1
HEOS Amp Song Name 2
Denon DSW-1H not paired-tap to conigure

Denon DSW-1H
Pair Subwoofer Select a HEOS device to pair your Denon DSW-1H with:
HEOS 1 + HEOS 1 HEOS Amp

Rooms
.

Music

Now Playing

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Unpairing the DSW-1H
1 Tap the pencil e icon in the upper right corner of the "Rooms" menu.
2 Tap the HEOS device from which to unpair the DSW-1H. 3 Select "Disconnect Wireless Subwoofers"

Rooms
Drag one room into another to group them HEOS 3 Left
HEOS Link
Denon DHT-S716H
HEOS 3 Right

Name

Edit Group
Denon DHT-S716H

Disconnect Wireless Surrounds Disconnect Wireless Subwoofers

Denon DHT-S716H
.

Music

HDMI In

Contents

Setup

Use

Making adjustments
You can adjust specific settings for each of your HEOS device in your system:
1 Select the Settings a icon located in the upper left corner of the main "Music" menu to display the Settings menu.
2 Select "My Devices" to display a list of your HEOS devices.
3 Select the HEOS device you want to adjust.

Troubleshooting

Status LED

Appendix

Adjusting the Level
1 Select "Level". 2 Adjust the level up or down to compensate for the
subwoofer output level.

0 You can also configure settings by tapping S in the Now Playing screen.
Adjusting the Low Pass Filter

1 Select "Low Pass Filter".

2 Set the frequency cutoff point.

Optimized (recommended)

Select when using with HEOS speakers. Optimized values are set to each of the speakers.

40Hz - 250Hz (for experts)

When using with other speakers, configure settings that match the characteristics of the combined speakers.

Contents

Setup

Use

Troubleshooting

Adjusting the Phase
1 Select "Phase". 2 Select Normal (default) or 180°.

0 For normal configuration, use "Normal". 0 The bass volume may increase when switched to "180°" due to the installation
location of the Subwoofer.
Adjusting the status light brightness
1 Select "Status Light". 2 Adjust the brightness up or down or set the slider to
the OFF position to completely disable the status light.

Status LED

Appendix

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Updating your system

HEOS has the ability to add enhancements and updated functionality via your high speed Internet connection. Follow the instructions on the screen to update the HEOS device and/or your controller App.

1 Select the Settings a icon located in the upper left corner of the main "Music" menu to display the Settings menu.

2 Select "Software Update".
n Check for Update
Follow the instructions on screen to install any available updates to your HEOS system.

n Auto-Update
ON (Default):
OFF:

Valid updates are performed automatically.
You will be notified of valid updates on the HEOS app.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Advanced features

There are a few advanced features of the HEOS system that you may want to explore once you become familiar with the basic operations. You can access the advanced features of the HEOS system by following these steps:

1 Select the Settings a icon located in the upper left corner of the main "Music" menu to display the Settings menu.
2 Select "Advanced Settings" to display a list the available settings.

Wireless performance
You can check the wireless connection status of your HEOS device.
n Quality
Excellent / Good / Poor

NOTE 0 If the quality level of your HEOS device is "Poor", make sure your HEOS devices
are not located near other electronic devices that could interfere with it's wireless connectivity (like microwave ovens, cordless phones, TVs, etc...)
n Signal
Excellent / Good / Poor

NOTE
0 If the signal level of your HEOS device is "Poor", make sure your HEOS devices are within range of your wireless network.

Contents

Setup

Power management

Use

Troubleshooting

Status LED

Appendix

Power modes
o Quick Start Mode
To save power, the device will automatically enter "Quick Start Mode" whenever there is no network access or playback for 20 minutes and will automatically resume to full power whenever the device is selected and playing music. The status LED dims when the mode is switched to Quick Start Mode.

o Deep Standby
The device also has the ability to automatically enter "Deep Standby" whenever the wired and wireless network connections are removed for more than 60 minutes in Quick Start Mode. Status LED will turn off during Deep Standby. To "wake" a HEOS device from Deep Standby, you must press the volume or mute buttons which will immediately turn on the front panel LED.
NOTE 0 Please note that the HEOS cannot be operated as intended when in Deep
Standby as there is no network connection.
o Off
To completely turn off the power to the device you must remove the mains plug from the power outlet.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Basic troubleshooting
My HEOS device won't connect to my network using the audio cable
Solution 0 Make sure your mobile device is connected to your wireless network before setting up your device. 0 Alternatively, you can connect your device to your network router using the included Ethernet cable. Once connected via
Ethernet, the HEOS App should recognize the device and you can manually move it to your wireless network using Settings/My Devices/Device_Name/Advanced/Network Settings.

Refer to Page 15 16

My HEOS device turns off and the status LED flashes in red
Solution 0 The protection circuit has been activated due to a rise in temperature within your HEOS device. Turn the power off, wait about
an hour until this device cools down sufficiently, and then turn the power on again.

Refer to Page

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Connecting to a WPS network
Solution
0 If your wireless router support WPS (Wi-Fi Protected SetupTM) your HEOS wireless device can optionally connect to your network using the "Push Button" method by following these steps:
Wi-Fi Protected SetupTM is trademarks of Wi-Fi Alliance.
1. Press the WPS button on your router. 2. Within 2 minutes, press and hold the Connect button on the rear panel of the HEOS device for 3 seconds. 3. The LED on the front of the device will flash green for several seconds as it connects to your WPS router. 4. When the connection is complete, the LED on the front of the device will turn solid blue.

Refer to Page 5

Resetting your HEOS device
Solution
0 Resetting your HEOS device will clear out the wireless network info, EQ, and name but retain it's current software. You will have to use Settings - Add Device to reconnect the HEOS device to your home network before it can be used. To reset your HEOS device, press and hold the RESET buttons located on the back of the HEOS device for 5 seconds until the front LED begins to flash amber.

Refer to Page

Contents

Setup

Status LED table

Device Operation

Use Description

Off

No AC power or Deep Standby

Troubleshooting

Status LED

Front LED Action
.
(off)

Plug in

Booting

.
(blink)

Ready-Configured and connected to your network

.
(solid)

Not Connected to your network

.
(solid)

Change Network

Connecting to your network

.
(blink)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

Contents Device Operation

Setup

Not connected

Use Description

Setup

Connect button was pressed Cable connection is OK

Connecting to your network

Troubleshooting

Status LED

Front LED Action

.
(solid)
.
(blink)

.
(solid)

.
(blink)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(blink)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

Contents Device Operation

Setup

Use Description

Troubleshooting

Status LED

Front LED Action

Setup

Configured and connected to your network Error

.
(solid)
.
(solid)

Updating

.
(blink)

Update

Rebooting

.
(blink)

Ready-Configured and connected to your network

.
(solid)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(blink)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

Contents Device Operation

Setup

Use Description

Soft reset - Clear user settings

Reset

Hard reset - Factory restore Rebooting

Ready-Not Configured

Troubleshooting

Status LED

Front LED Action

.
(fast blink)

.
(blink)

.
(solid)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

Contents Device Operation

Setup

Firmware Error

Errors

Hardware Error

Network Error

Use Description

Troubleshooting

Status LED

Front LED Action

.
(slow blink (NOT fade))

.
(fast blink)

.
(solid)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

Contents Device Operation

Setup

Use Description

a WPS session is active

WPS

WPS connected

WPS time-out

Quick Start Mode Power Management
Deep Standby

Troubleshooting

Status LED

Front LED Action

.
(fast blink)

.
(for 3 sec. solid)

.
(dimmed solid)
.
(off)

Appendix

Rear LED Action

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(fast blink)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(solid)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

AUX IN

USB 5V/1A---

NETWORK

RESET

AC IN

CONNECT

.
(off)

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

Supported file types and codecs

Frequency
32/44.1/48 88.2/96/176.4 192 kHz
32 kHz 44.1 kHz 48 kHz
32 kHz 44.1 kHz 48 kHz
32 kHz 44.1 kHz 48 kHz
44.1/48 88.2/96/176.4 192 kHz
44.1/48 88.2/96/176.4 192 kHz
2.8/5.6 MHz

Sample Rate 16/24 bit

File Extension

wav

PCM

Codec

16 bit 16 bit 16 bit

mp3
m4a aac
wma

MPEG-1 Audio Layer 3 CBR/VBR
AAC-LC
wma9 CBR

16/24 bit

flac

16/24 bit

m4a

1 bit

dff dsf

ALAC
DSDIFF DSF

Bit Rates ---
32 - 320 kbps 48 - 320 kbps CBR:48 - 192 kbps
-------

NOTE 0 Files protected by DRM such as Apple's Fairplay DRM, are not supported. 0 The ALAC decoder is distributed under the Apache License, Version 2.0 (http://www.apache.org/licenses/LICENSE-2.0)

Contents

Setup

Use

Troubleshooting

Specifications

o Wireless LAN section
Network type: Used frequency range:
o General
Operating temperature: Power supply: Power consumption: Power consumption in Quick Start Mode: Power consumption in Deep Standby Mode:

Conforming to IEEE 802.11a/b/g/n/ac 2.4 GHz, 5 GHz
41 °F - 95 °F (5 °C - 35 °C) AC 100 - 240 V, 50/60 Hz 70 W 4.5 W 0.3 W

Status LED

Appendix

Contents

Setup

o Dimensions (Unit : in. (mm))

Use

Troubleshooting

Status LED

Appendix

6 7/8 (172)

17 3/8 (439)

15 7/8 (403) 16 (404)

.
o Weight : 22 lbs 4 oz (10.1 kg)
For the purpose of improvement, the specifications and design are subject to change without notice.
35

Contents
Information
Trademarks

Setup

Use

Troubleshooting

Status LED

Appendix

.
Google Play and the Google Play logo are trademarks of Google LLC.

.
Amazon, Kindle, Echo, Alexa, Dash, Fire and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

.
Apple, the Apple logo, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

License

o License information for the software used in the unit
About GPL (GNU-General Public License), LGPL (GNU Lesser General Public License) License
This product uses GPL/LGPL software and software made by other companies.
After you purchase this product, you may procure, modify or distribute the source code of the GPL/LGPL software that is used in the product.
Denon provides the source code based on the GPL and LPGL licenses at the actual cost upon your request to our customer service center. However, note that we make no guarantees concerning the source code. Please also understand that we do not offer support for the contents of the source code.
This section describes software license used for this unit. To maintain the correct content, the original (English) is used.

n GPL

Open Source Used bridge-utils busybox ebtables Linux kernel mtd-utils ntfs-3g_ntfsprogs ntpclient u-boot wireless-tools

2.8 1.21.1 2.0.10-4 3.10.74 1.4.3 2011.4.12 2007 2015.01 version 29

Version

n LGPL

Open Source Used ffmpeg glibc libmms

0.8.3 2.9 0.6.2

Version

n curl-7.24.0
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2014, Daniel Stenberg, <daniel@haxx.se>
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n e2fsprogs-libs-1.40.8/lib/uuid
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, and the entire permission notice in its entirety, including the disclaimer of warranties.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH ARE HEREBY DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

n expat-2.0.1
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n getopt
http://cvsweb.netbsd.org/bsdweb.cgi/src/lib/libc/stdlib/
Copyright (c) 1987, 1993, 1994 The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

n jQuery
Copyright 2014 jQuery Foundation and other contributors
http://jquery.com/
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n libpcap-1.4.0
License: BSD
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The names of the authors may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

n libtar-1.2.11
Copyright (c) 1998-2003 University of Illinois Board of Trustees
Copyright (c) 1998-2003 Mark D. Roth
All rights reserved.
Developed by: Campus Information Technologies and Educational Services, University of Illinois at Urbana-Champaign
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal with the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
z Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers.
z Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution.
z Neither the names of Campus Information Technologies and Educational Services, University of Illinois at Urbana-Champaign, nor the names of its contributors may be used to endorse or promote products derived from this Software without specific prior written permission.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE CONTRIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS WITH THE SOFTWARE.

Contents

Setup

Use

n mDNS 320.10.80
The majority of the source code in the mDNSResponder project is licensed under the terms of the Apache License, Version 2.0, available from:
<http://www.apache.org/licenses/LICENSE-2.0>
To accommodate license compatibility with the widest possible range of client code licenses, the shared library code, which is linked at runtime into the same address space as the client using it, is licensed under the terms of the "Three-Clause BSD License".
The Linux Name Service Switch code, contributed by National ICT Australia Ltd (NICTA) is licensed under the terms of the NICTA Public Software Licence (which is substantially similar to the "Three-Clause BSD License", with some additional language pertaining to Australian law).

Troubleshooting

Status LED

Appendix

n mongoose
https://github.com/cesanta/mongoose/
Copyright (c) 2004-2013 Sergey Lyubka
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n openssl-1.0.0d
Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.
5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n portmap-6.0
Copyright (c) 1990 The Regents of the University of California.
z All rights reserved.
z Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. A ll advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
z THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

n pstdint.h-0.1.12
z BSD License:
z Copyright (c) 2005-2011 Paul Hsieh
z All rights reserved.
z Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
z THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
z IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n rl78flash 2000.3.1
License
=======
The MIT License (MIT)
Copyright (c) 2012 Maxim Salov
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

n sqlite 2003.5.7
SQLite Copyright
SQLite is in the
Public Domain
All of the code and documentation in SQLite has been dedicated to the public domain by the authors. All code authors, and representatives of the companies they work for, have signed affidavits dedicating their contributions to the public domain and originals of those signed affidavits are stored in a firesafe at the main offices of Hwaci. Anyone is free to copy, modify, publish, use, compile, sell, or distribute the original SQLite code, either in source code form or as a compiled binary, for any purpose, commercial or non-commercial, and by any means.
The previous paragraph applies to the deliverable code and documentation in SQLite - those parts of the SQLite library that you actually bundle and ship with a larger application. Some scripts used as part of the build process (for example the "configure" scripts generated by autoconf) might fall under other open-source licenses. Nothing from these build scripts ever reaches the final deliverable SQLite library, however, and so the licenses associated with those scripts should not be a factor in assessing your rights to copy and use the SQLite library.
All of the deliverable code in SQLite has been written from scratch. No code has been taken from other projects or from the open internet. Every line of code can be traced back to its original author, and all of those authors have public domain dedications on file. So the SQLite code base is clean and is uncontaminated with licensed code from other projects.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n strlcpy.c , v1.11
z Copyright (c) 1998 Todd C. Miller <Todd.Miller@courtesan.com>
z Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.
z THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
n taglib-1.5
copyright : (C) 2002 - 2008 by Scott Wheeler email : wheeler@kde.org
"The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/ Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License for the specific language governing rights and limitations under the License.

n tinyxml 2002.4.3
www.sourceforge.net/projects/tinyxml Original file by Yves Berquin.
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.

Contents

Setup

Use

Troubleshooting

Status LED

Appendix

n Tremor
http://wiki.xiph.org/index.php/Tremor
Copyright (c) 2002, Xiph.org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

n zlib
http://www.zlib.net/ zlib.h -- interface of the 'zlib' general purpose compression library version 1.2.3, July 18th, 2005 Copyright (C) 1995-2004 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly jloup@gzip.org, Mark Adler madler@alumni.caltech.edu

Contents

Setup

Use

n The Spotify software is subject to third party licenses found here:
www.spotify.com/connect/third-party-licenses

Troubleshooting

Status LED

Appendix

.
www.denon.com
48