AXXESS AXTC-FD1 0086429375752 Black
solder, and heat shrink • Tape • Wire cutter. • Zip ties ... Ford SWC (Steering Wheel Control) ... Auto detects vehicle type, radio.
englishopens a new window
APPLICATIONS See inside front cover AxxessInterfaces.com AXTC-FD1 INSTALLATION INSTRUCTIONS Ford SWC (Steering Wheel Control) and Data Interface 2007-up INTERFACE FEATURES · Provides accessory power (10-amp) · Ability to dual assign steering · Provides wires for multimedia wheel control buttons radios (park brake, reverse, · Retains memory settings even speed sense) after battery disconnection or · Retains audio controls on the interface removal (non volatile steering wheel memory) · Designed to be compatible with · Provides illumination output all major radio brands · Micro-B USB updatable · Auto detects vehicle type, radio · Includes 5v factory amplifier connection, and preset controls step-down TABLE OF CONTENTS Applications............................................................2 Connections. ........................................................... 3 Programming.........................................................4 Troubleshooting.....................................................5 INTERFACE COMPONENTS · AXTC-FD1 interface · AXTC-FD1 harness · 3.5mm adapter · LD-AFDI-5V amplifier step-down TOOLS & PARTS REQUIRED · Crimping tool and connectors, or solder gun, solder, and heat shrink · Tape · Wire cutter · Zip ties Product Info © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 7/11/19 INSTAXTC-FD1 APPLICATIONS Ford SWC* Edge 2007-2010 (auto) Escape 2008-2012 (auto) Expedition 2007-2014 (auto) Exporer (1) 2009-2010 (auto) F-150 (2) 2013-2014 (tap) F-150 (3) 2011-2012 (tap) F-150 (3) 2009-2010 (auto) F-250/350/450/550 XL/XLT (2) 2013-2016 (tap) F-250/350/450/550 XL/XLT (3) 2011-2012 (tap) Focus 2008-2011 (auto) Fusion 2010-2012 (auto) Mustang 2009-2014 (auto) Mustang (4) 2008.5 (auto) Taurus 2010-2012 (auto) Lincoln MKX MKZ Navigator Mazda Tribute Mercury Mariner Milan SWC* 2007-2010 (auto) 2007-2009 (auto) 2007 (auto) SWC* 2008-2011 (auto) SWC* 2008-2011 (auto) 2010-2012 (auto) (1) With NAV (2) Without 8.4" color screen. XL models must have a CD player (3) XL models must have a CD player (4) Late 2008 build date *SWC Programming Sequence (auto) Do nothing, the interface will auto program (tap) Tap the Volume Up button to program the interface 2 CONNECTIONS Reset Button LED Light Front Rear 3.5mm Adapter (for radios with a wire for SWC) Sub Boss (with SWC wire): Key 1 (Gray) - Brown Kenwood / JVC (with SWC wire): Blue/Yellow - Brown XITE: SWC-2 - Brown Universal Radio*: Key-A or SWC-1 - Brown Key-B or SWC-2 - Brown/White * After programming, assign SWC buttons within radio menu Aftermarket Radio (radio's features may vary) AUX-IN Rear View SWC LD-AFDI-5V Vehicle Connectors Radio Connections Black - Ground Yellow - Battery power Red - Accessory power Orange - Illumination Blue - Power Antenna Blue/White - See below Blue/White - See below Blue/Pink - VSS/Speed-Sense Green/Purple - Reverse signal Light Green - Parking brake Gray - Front right speaker + Gray/Black - Front right speaker White - Front left speaker + White/Black - Front left speaker Green - Rear left speaker + Green/Black - Rear left speaker Purple - Rear right speaker + Purple/Black - Rear right speaker Black - Ground Blue/White - Amp turn-on from radio Blue/Red - AXTC-FD1 Blue/White wires (2) REV. 7/11/2019 INSTAXTC-FD1 3 PROGRAMMING 1. Open the driver's door, and keep open during the programming process. 2. ACC ON Cycle the ignition on. START OF F 3. Connect the AXTC-FD1 harness to the AXTC-FD1 interface, and then to the wiring harness in the vehicle. 4. Do Not Touch For (auto*) vehicles: Do not touch the steering wheel controls, the VOL interface will auto program. + Tap Volume Up VOL + For (tap*) vehicles: Locate the Volume Up button on the steering wheel. Program the interface by tapping the Volume Up button at a heartbeat pace until the LED light stops flashing. *Refer to the application list on page 2 5. The LED light will flash Green & Red while the interface programs the radio to the steering wheel controls. Once programmed, the LED light Green & Red LED will go out, then produce a pattern which will identify the radio type installed. Green or Red LED 6. The LED light will go out, then once again quickly flash Green & Red while the interface programs itself to the vehicle. Once programmed, Green & Red LED the LED light will go out again, then turn solid Green. Green LED 7. ACC ON START OF F Cycle the ignition off, then back on. ACC ON START OF F 8. Test all functions of the installation for proper operation. 4 TROUBLESHOOTING 1. If the interface fails to function, press and release the reset button, then repeat the programming process from step 4 to try again. LED Reset Light Button 2. Final LED Feedback At the end of programming the LED light will turn Solid Green which indicates programming was successful. If the LED light didn't turn Solid Green, reference the list below to understand which programming section the problem may stem from. LED Light Solid Green Slow Red Flash Slow Green Flash Solid Red Radio Programming Section Pass Fail Pass Fail Vehicle Programming Section Pass Pass Fail Fail Note: If the LED light shows Solid Green for Pass (indicating everything programmed correctly), yet the steering wheel controls don't work, check to ensure that the 3.5mm jack is plugged in, and also plugged into the correct jack on the radio. Once corrected, press the reset button, then program again. QR Code Scan Here Further troubleshooting steps and information can be located at: axxessinterfaces.com/product/AXTC-1-FD1 REV. 7/11/2019 INSTAXTC-FD1 5 6 REV. 7/11/2019 INSTAXTC-FD1 7 AxxessInterfaces.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION AXTC-FD1 INSTALLATION INSTRUCTIONS Having difficulties? We're here to help. Contact our Tech Support line at: 1-800-253-TECH Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians REV. 7/11/19 INSTAXTC-FD1Adobe InDesign 14.0 (Macintosh) Adobe PDF Library 15.0